Page Index - Phil1988/FreeDi GitHub Wiki
148 page(s) in this GitHub Wiki:
- Home
- Welcome to the FreeDi Wiki - a firmware to support Qidi X3 series printers and more
- Overview
- Key Highlights
- Getting Started
- Support and Contributions
- Additional Video Guide for the X‐Smart 3
- Please reload this page
- Advanced Configuration Section
- Please reload this page
- Bed Leveling Guide
- Please reload this page
- Bed PID Tuning
- Please reload this page
- Bugs!
- Please reload this page
- Calibrate Z‐Offset
- Please reload this page
- Cartographer
- Please reload this page
- Changing the system time
- Please reload this page
- Common issues
- Please reload this page
- Community
- Please reload this page
- Configuration Basics for Beginners
- Please reload this page
- Configuration Files
- Please reload this page
- Correct tilted print bed
- Please reload this page
- Creating a backup
- Please reload this page
- Creating backups
- Please reload this page
- Enabling time lapse
- Please reload this page
- Expanding the filesystem (for larger storage devices)
- Please reload this page
- FAQ
- Please reload this page
- Features
- Please reload this page
- Fine‐Tuning Z‐Offset with Test Prints
- Please reload this page
- Flashing EMMC via USB Stick (No EMMC Reader Needed)
- Please reload this page
- Flashing the display
- Please reload this page
- Flashing the screen firmware via microSD card
- Please reload this page
- Flashing the toolhead ‐ Plus4
- Please reload this page
- Flashing the toolhead ‐ Q1 Pro
- Please reload this page
- Flashing the toolhead ‐ X3 series
- Please reload this page
- Future features
- Please reload this page
- How to report bugs
- Please reload this page
- Important note about backups
- Please reload this page
- Initial Setup & Calibration
- Please reload this page
- Input Shaping Calibration
- Please reload this page
- Installation guide
- Please reload this page
- Installation guide for existing systems
- Please reload this page
- Installation guide for existing systems (for firmwares up to v1.03)
- Please reload this page
- Installation guide for fresh systems
- Please reload this page
- Installation guide for fresh systems (for firmwares up to v1.03)
- Please reload this page
- Installing a camera
- Please reload this page
- Interaction between software and the display
- Please reload this page
- Introduction
- Please reload this page
- landing_page_old
- Please reload this page
- Lookup commands for my alpha squad
- Please reload this page
- lp kurz
- Please reload this page
- lp1
- Please reload this page
- Menu guide
- Please reload this page
- Nozzle PID Tuning
- Please reload this page
- OrcaSlicer Setup
- Please reload this page
- Plus4 mainboard MCU
- Please reload this page
- Post install and config section
- Please reload this page
- Preserving printing history
- Please reload this page
- QIDI Slicer Setup
- Please reload this page
- Requirements
- Please reload this page
- Restoring the stock firmware [Plus4]
- Please reload this page
- Slicer Setup
- Please reload this page
- Step #2: Flashing the toolhead (Plus4)
- Please reload this page
- Step #2: Flashing the toolhead (Q1 Pro)
- Please reload this page
- Step #3: Installation completed
- Please reload this page
- Tour #1: Installing FreeDi
- Please reload this page
- Tour #1: Requirements
- Please reload this page
- Tour #2: Adjusting the printer config
- Please reload this page
- Tour #2: Installing FreeDi
- Please reload this page
- Tour #2: Requirements
- Please reload this page
- Updating FreeDi
- Please reload this page
- Video guide
- Please reload this page
- Which screen firmware should I use?
- Please reload this page
- Why
- Please reload this page
- Why creating a backup is important
- Please reload this page
- Wifi activation
- Please reload this page
- Wizard info page: Plus4
- Please reload this page
- Wizard info page: Q1 Pro
- Please reload this page
- Wizard info page: X3 series
- Please reload this page
- Z‐Offset Calibration (Coarse)
- Please reload this page