CX Cards
Conexant CX2388x-xx is an 2002 era PCI-based chip, today found with a PCIe bridge chip (Asmedia or ITE) in the 1x PCIe desktop card form factor.
With CXADC it becomes an powerful 28-40msps 8-bit Analogue to Digital Converter!
CX White (CX23883-39) S-Video/RCA input.
This page has overview information, for more in-depth information on the driver and cards click the links below.
Recommended card type: White CX25800
AliExpress is currently the best supplier of the CX White Card at 16~30 USD.
Why PCIe 1x Cards and not any old PCI card?
Hardware standardization makes it easier to support the software/hardware interoperability for RF Capture. A standardized PCB layout, with predictable and dependably similar performance, allows for easy modification, standardized guides, and sample comparison.
For Video8/Hi8/LaserDisc FM RF capture you will only need one card for Video/HiFi RF, but will benefit from a crystal mod.
For SMPTE-C/SMPTE-B you will only need one card for Video RF but will require a synchronised solution for Audio/Timecode.
Buy 2 or more if you wish to do
- VHS/SVHS/Betamax/SuperBeta Video + HiFi (now with synchronised timing!)
- Betacam/Betacam SP/MI/MII/W-VHS dual video channel capture.
- Have a flexible setup or do multiple decks at the same time.
Owning an RTLSDR is ideal for calibrating HiFi while servicing or adjusting an VCR, or If you already have a DomesDay Duplicator it's a defacto addition for HiFi FM capture.
The CXADC driver now supports upto 256 cards so setups can be scaled as much as you need, and external timing sources allow it to do clock locked sampling of different signals in the same deck, so zero hardware audio/video drift issues.
On the white card without physical modification, it's recommended to use the S-Video port (Luma or Y signal pin and ground) for FM RF signal capture if you wish to not solder your own cables or modify the card in any way.
The CX chips have an internal digital gain amplifier, which if used, can generate unwanted self noise. To mitigate this, you may use an external amplifier to increase the amplitude before it gets to the card, this can also compensate for longer cabling if unavoidable.
An external RMS amplifier is an affordable way to negate the issue and is a soft mod to the capture chain in most setups for tape formats, and can even be powered by a VCRs internal 5V or 12V connections.
| AD8367 AGC Amp | Fixed Amp |
Caution
The AD8367 boards are 3-5v range only if voltage is 6-12v+ a buck boost converter or regulator to lower the voltage will be required.
Jumper configuration in automatic gain mode "AGC".
The off shelf go-to today is the Analog Devices AD8367 based boards / Pot-less AliExpress Link / With Pot AliExpress Link / 4.5v AA Battery Holder / Wiki Setup Link
There is also other amplifiers available that are more fine tuned for FM capture with the CX Cards.
ADA4857 based board by Rene Wolf
Adding a 40x40mm heat sink & fan is also recommended.
Faster sampling data output = more heat = shorter hardware life and possible loss of capture data due to overheating.
File the heat sink's mounts down, so as not to touch board components. Secure the heat sink & fan unit onto the chip. Do NOT forget to use thermal paste and/or thermal pad on the heat sink, putting tape around the metal is also a good idea but be sure not to obstruct the chip.
Silicone is recommended over hot glue due to the risk of melting, and ease of removal without damaging parts.
Requirements:
- Soldering Iron with Bevel/Chisel Tip, Flux, 60/40 Solder
- 40x40mm heat sync & fan
- Thermal Pad / Thermal Paste
- Silicone Glue
Features:
- Improved signal to noise ratio
Note
The label on the white card picture above these cards have a bridging capacitor on pad C31 this bridges the 2 input pads for RCA/BNC connectors, and causes worse captures due to adding signal reflections.
Its best to always remove either with a iron tap both sides then lightly pressure from one side to knock it off the 2 pads its soldered to, or remove with a gentle twist with tweezers/plyers.
With de-soldering and a pair of flush cutters, you can replace the RCA connector and or add another input with BNC which is a lot more reliable and flexible than RCA.
Can I just use the unpopulated pad? (get a drill bit and make a new hole bracket and you can)
AliExpress / Amazon US / Amazon UK / eBay / Walmart Canada
Features:
- Increased Sampling Speed
Note
CX Cards can go up-to 57Mhz on some cards, with 48Mhz being possible on most white card variants with 40Mhz being the standard choice as its the most optimal SNR wise for the ADC.
This simple "cheep and dirty" modification is just replacing the stock crystal with a soldering iron, an instant drop-in upgrade to 40msps 8-bit capture or 20msps 16-bit capture, though the CX2388x-xx cards are made for upto 54mhz crystal support in testing 40mhz is generally achievable by any card and matches the DomesDayDuplicator, this also improves the SNR of the CX Chips.
This mod makes the cards ideal for Video8/Hi8/SVHS/ED-Beta/SMPTE 1" & LaserDisc capture on a budget.
The Crystal: Generic 40mhz Fundamental or ABRACON ABLS2-40.000MHZ-D4YF-T Digikey / Farnell (can be sorced from most vendors)
Note
Adding a 40mm heat sync & fan is also recommended more data = more heat = shorter hardware life and possible loss of capture data.
Note
Not all crystals are perfect and some can be defective and dramatically out of spec.
The most advanced mod available today, using an external crystal timing source we can have drift free capture with 2-4 CX Cards and audio feeds.
Features:
- Software Defined Crystal Rate
- Hardware Synchronised Multi-Card Capture
- Additional ADC for Synchronised Linear/Baseband Audio Capture
This allows duel channel video formats such as Betacam to be captured, or Video FM + HiFi FM + Linear for many other formats like VHS or Betamax.
Possible thanks to cxadc-clock-generator-audio-adc By Rene Wolf
External crystal timing via 2 additional PCB boards, a Jig with an SMA and Mainboard has allowed for under 50USD multi card sync, using 2 or more CX Cards alongside a extra input for synchronised Linear/Reference audio capture also has a extra input for headswiching timing signals.
-
Raspberry Pi Pico as the interface and control board.
-
Adafruit Si5351A for generating the shared clock source with 5 potential inputs.
-
PCM1802 ADC for L/R input Linear/HiFi audio capture.
Audio Inputs and Headswitch Input is on a dedicated bracket you can 3D print.
Clock Speed & Audio is controlled by a CLI application.
For laserdisc you may want to use the LPF mod (low pass filter) and more information can be read in greater details here: