Wall Climate Control Devices - Niilo007/Stationeers-Research GitHub Wiki

Wall Climate Control Devices

Kit (Wall Cooler)

This kit creates a Wall Cooler.

Kit (Wall Cooler)
____________ General ____________ ____________ ____________
Paintable ✔
Nameable ❌
Prefab Hash -1567752627
Prefab Name ItemWallCooler
______________ Item ______________ ____________ ____________
Stack Size 5
Class None 0
SortingClass Kits 1
____________ Durability ____________ ____________ ____________
Flashpoint Temperature 1200℃
Autoignition Temperature 800℃
Made In Hydraulic Pipe Bender T1 Hydraulic Pipe Bender T2
alt text alt text
Time 5s 3.3s
Energy 500
Iron Fe 3g 3g
Gold Au 1g 1g
Copper Cu 3g 3g

Structure (Wall Cooler)

The Xigo Freezy Boi wall cooler complements the wall heater, which can only raise the temperature. The wall cooler functions by drawing heat from the surrounding atmosphere and adding that heat into its pipe network.

In order to run the wall cooler properly, you will need to connect pipes to the wall cooler and fill the connected pipe network with any type of gas. The gas's heat capacity and volume will determine how fast it reacts to temperature changes.

EFFICIENCY
The higher the difference in temperature between the gas stored in the pipes and the room, the less efficient the wall cooler will be. So to keep the wall cooler running at an acceptable efficiency you will need to get rid of the heat that accumulates in the pipes connected to it. A common practice would be to run the pipes to the outside and use radiators on the outside section of the pipes to get rid of the heat.

The less efficient the wall cooler, the less power it consumes. It will consume 1010W at max efficiency. The wall cooler can be controlled by logic chips to run when the temperature hits a certain degree.

ERRORS
If the wall cooler is flashing an error then it is missing one of the following:

  • Pipe connection to the wall cooler.
  • Gas in the connected pipes, or pressure is too low.
  • Atmosphere in the surrounding environment or pressure is too low.

For more information about how to control temperatures, consult the temperature control Guides page.

  • Starts losing cooling power when the temperature differential between the room and the pipe is greater than 100℃.
    alt text
  • The data disk slot doesn't serve a purpose.
  • Only works if the pipe and local atmosphere has at least 6.3kPa of pressure.
    • The Error logic value will read a 1.
Wall Cooler
____________ General ____________ ____________ ____________
Paintable ✔
Nameable ✔
Prefab Hash -739292323
Prefab Name StructureWallCooler
____________ Durability ____________ ____________ ____________
Flashpoint Temperature NA
Autoignition Temperature NA
_________ Construction _________ ____________ ____________
Placement Cost Kit (Wall Cooler) 1
............................................................. ......................... .........................
Deconstruction Tool Hand Drill
____________ Power ____________ ____ Min ____ ____ Max ____
Power Use 10W 1010W
Heat Generation 0W -1000W
Placement Dimensions
Snapping Small Grid Length 1
Rotation Any Height 1
Required Support Wall Width 1
Device Logic Variables Type Min Max Read Write Device Specific Behaviours
Power bool 0 1 ✔ ❌
Error bool 0 1 ✔ ❌
Lock bool 0 1 ✔ ✔
Setting int 0 100 ✔ ✔
Maximum int 100 100 ✔ ❌
Ratio float 0 1 ✔ ❌
On bool 0 1 ✔ ✔
RequiredPower int 0 10 ✔ ❌
PrefabHash int -739292323 -739292323 ✔ ❌
ReferenceId int ✔ ❌
Slot

 Name
Class		 Icon
0 DataDiskSlot
Data Disk
Logic Slots Type Min Max Read Write Slots Device Specific Behaviours
Occupied bool 0 1 ✔ ❌ 0
OccupantHash int ✔ ❌ 0
Quantity 0 ✔ ❌ 0
Damage float 0 1 ✔ ❌ 0
Class ? int 0 34 ✔ ❌ 0
MaxQuantity 0 ✔ ❌ 0
PrefabHash int ✔ ❌ 0
SortingClass ? int 0 7 ✔ ❌ 0
Connections Port Description
Pipe 0 Waste heat exhaust.
Power And Data 1

Kit (Liquid Wall Cooler)

Kit (Liquid Wall Cooler)
____________ General ____________ ____________ ____________
Paintable ✔
Nameable ❌
Prefab Hash -1721846327
Prefab Name ItemWaterWallCooler
______________ Item ______________ ____________ ____________
Stack Size 5
Class None 0
SortingClass Kits 1
____________ Durability ____________ ____________ ____________
Flashpoint Temperature 1200℃
Autoignition Temperature 800℃
Made In Hydraulic Pipe Bender T1 Hydraulic Pipe Bender T2
alt text alt text
Time
Energy 500
Iron Fe 3g 3g
Gold Au 1g 1g
Copper Cu 3g 3g

Structure (Liquid Wall Cooler)

  • Works just like the Wall Cooler, but uses liquid for the waste heat instead of gas.
  • Starts losing cooling power when the temperature differential between the room and the pipe is greater than 100℃.
    alt text
  • The data disk slot doesn't serve a purpose.
  • Only works if the pipe and local atmosphere has at least 6.3kPa of pressure.
    • The cooler consumes 10W of idle power in this state.
    • The Error logic value will read a 1.
Liquid Wall Cooler
____________ General ____________ ____________ ____________
Paintable ✔
Nameable ✔
Prefab Hash -1369060582
Prefab Name StructureWaterWallCooler
____________ Durability ____________ ____________ ____________
Flashpoint Temperature NA
Autoignition Temperature NA
_________ Construction _________ ____________ ____________
Placement Cost Kit (Liquid Wall Cooler) 1
............................................................. ......................... .........................
Deconstruction Tool Hand Drill
____________ Power ____________ ____ Min ____ ____ Max ____
Power Use 10W 1010W
Heat Generation 0W -1000W
Placement Dimensions
Snapping Small Grid Length 1
Rotation Any Height 1
Required Support Wall Width 1
Device Logic Variables Type Min Max Read Write Device Specific Behaviours
Power bool 0 1 ✔ ❌
Error bool 0 1 ✔ ❌
Lock bool 0 1 ✔ ✔
Setting int 0 100 ✔ ✔
Maximum int 100 100 ✔ ❌
Ratio float 0 1 ✔ ❌
On bool 0 1 ✔ ✔
RequiredPower int 0 10 ✔ ❌
PrefabHash int -1369060582 -1369060582 ✔ ❌
ReferenceId int ✔ ❌
Slot

 Name
Class		 Icon
0 DataDiskSlot
Data Disk
Logic Slots Type Min Max Read Write Slots Device Specific Behaviours
Occupied bool 0 1 ✔ ❌ 0
OccupantHash int ✔ ❌ 0
Quantity 0 ✔ ❌ 0
Damage float 0 1 ✔ ❌ 0
Class ? int 0 34 ✔ ❌ 0
MaxQuantity 0 ✔ ❌ 0
PrefabHash int ✔ ❌ 0
SortingClass ? int 0 7 ✔ ❌ 0
Connections Port Description
Pipe Liquid 0 Waste heat exhaust.
Power And Data 1

Kit (Wall Heater)

This kit creates a Wall Heater.

Kit (Wall Heater)
____________ General ____________ ____________ ____________
Paintable ✔
Nameable ❌
Prefab Hash 1880134612
Prefab Name ItemWallHeater
______________ Item ______________ ____________ ____________
Stack Size 5
Class None 0
SortingClass Kits 1
____________ Durability ____________ ____________ ____________
Flashpoint Temperature 1200℃
Autoignition Temperature 800℃
Made In Hydraulic Pipe Bender T1 Hydraulic Pipe Bender T2
alt text alt text
Time
Energy 500
Iron Fe 3g 3g
Gold Au 1g 1g
Copper Cu 3g 3g

Structure (Wall Heater)

The Xigo wall heater is a simple device that can be installed on a wall or frame and connected to power. When switched on, it will start heating the surrounding environment. It consumes 1010W of power and can be controlled by logic chips to run when the temperature hits a certain level.

  • The data disk slot doesn't serve a purpose.
  • Has 1000W of heating power.
  • Only works if the local atmosphere has at least 6.3kPa of pressure.
    • The heater consumes 10W of idle power in this state.
  • Heats the local atmosphere up to a maximum of 2227℃.
    • Uses only 10W when at max temperature.
Ignition Source!
Wall Heater
____________ General ____________ ____________ ____________
Paintable ✔
Nameable ✔
Prefab Hash 24258244
Prefab Name StructureWallHeater
____________ Durability ____________ ____________ ____________
Flashpoint Temperature NA
Autoignition Temperature NA
_________ Construction _________ ____________ ____________
Placement Cost Kit (Wall Heater) 1
............................................................. ......................... .........................
Deconstruction Tool Hand Drill
____________ Power ____________ ____ Min ____ ____ Max ____
Power Use 10W 1010W
Heat Generation 0W 1000W
Placement Dimensions
Snapping Small Grid Length 1
Rotation Any Height 1
Required Support Wall Width 1
Device Logic Variables Type Min Max Read Write Device Specific Behaviours
Power bool 0 1 ✔ ❌
Error bool 0 1 ✔ ❌
Lock bool 0 1 ✔ ✔
On bool 0 1 ✔ ✔
RequiredPower int 0 10 ✔ ❌
PrefabHash int 24258244 24258244 ✔ ❌
ReferenceId int ✔ ❌
Slot

 Name
Class		 Icon
0 DataDiskSlot
Data Disk
Logic Slots Type Min Max Read Write Slots Device Specific Behaviours
Occupied bool 0 1 ✔ ❌ 0
OccupantHash int ✔ ❌ 0
Quantity 0 ✔ ❌ 0
Damage float 0 1 ✔ ❌ 0
Class ? int 0 34 ✔ ❌ 0
MaxQuantity 0 ✔ ❌ 0
PrefabHash int ✔ ❌ 0
SortingClass ? int 0 7 ✔ ❌ 0
Connections Port Description
Power And Data 0
⚠️ **GitHub.com Fallback** ⚠️