Stack-Interposer Board V1.0 Pinout Reference

Status: Draft Project: Enigma-NG Author: Izzyonstage & GitHub Copilot Version: v.0.1.0 Associated Hardware Revision: Rev A Last Updated: 2026-09-02

Board_Layout.md is a visualisation-only document. Design narrative, specifications, and component rationale belong in Design_Spec.md. This file contains connector pinout references and board orientation notes only.

---

Orientation Convention

• The Stack-Interposer Board lies horizontally at the base of the Rotor Mini-Stack.
• The Stack-Output Board stands vertically on the left side — J1 (Stack-Output side) faces upward on that edge.
• The Stack-Input Board stands vertically on the right side — J2 (Stack-Input side) faces upward on that edge.
• Both J1 and J2 are straight/vertical male connectors on the top surface of this board (no right-angle), mounted protruding upward to span the enclosure gap and mate with the facing Stack-Output/Stack-Input board's flush-mounted female J6 socket. The right-angle connectors on the Stack-Output and Stack-Input bottom edges mate downward into J1 and J2 respectively. Mating gap/tolerance: design/Standards/Global_Routing_Spec.md §4.1a.

---

1. J1 — Stack-Output Mating Connector (TMMH-115-01-L-D-ES)

Connector Definition Owner: this document (Stack-Interposer Board_Layout.md §1). Mates with Stack-Output Board J6 (SQT-115-01-L-D-RA right-angle female on Stack-Output bottom edge). MPN: TMMH-115-01-L-D-ES (Samtec 30-position 2×15 straight/vertical male).

All J1 contacts connect directly to the corresponding J2 contacts (pin n → pin n). No signals are terminated or modified at this board.

---

2. J2 — Stack-Input Mating Connector (TMMH-115-01-L-D-ES)

Connector Definition Owner: this document (Stack-Interposer Board_Layout.md §2). Mates with Stack-Input Board J6 (SQT-115-01-L-D-RA right-angle female on Stack-Input bottom edge). MPN: TMMH-115-01-L-D-ES (Samtec 30-position 2×15 straight/vertical male).

All J2 contacts connect directly to the corresponding J1 contacts (pin n → pin n). No signals are terminated or modified at this board.

---

3. Pin Map — 2×15 Connector (applies to both J1 and J2)

The same signal assignment applies to both J1 and J2. Passive continuity: J1 pin n is connected directly to J2 pin n by a trace on L2 or L3. Signal naming is from the perspective of the Stack-Output Board (J1 side):

Row 1 signal	Pin (Row 1, odd)	Pin (Row 2, even)	Row 2 signal
ENC_DATA[0] (SIG-BLOCK-A fwd)	1	2	GND
GND	3	4	ENC_DATA[1] (SIG-BLOCK-A fwd)
ENC_DATA[2] (SIG-BLOCK-A fwd)	5	6	GND
GND	7	8	ENC_DATA[3] (SIG-BLOCK-A fwd)
ENC_DATA[4] (SIG-BLOCK-A fwd)	9	10	GND
GND	11	12	ENC_DATA[5] (SIG-BLOCK-A fwd)
TTD (SIG-BLOCK-E)	13	14	GND
ACTUATE_REQUEST (SIG-BLOCK-G, fwd, Stack-Output→Stack-Input)	15	16	ACTUATE_REQUEST (SIG-BLOCK-H, return, Stack-Input→Stack-Output)
GND	17	18	TTD (SIG-BLOCK-E)
ENC_DATA[5] (SIG-BLOCK-D return)	19	20	GND
GND	21	22	ENC_DATA[4] (SIG-BLOCK-D return)
ENC_DATA[3] (SIG-BLOCK-D return)	23	24	GND
GND	25	26	ENC_DATA[2] (SIG-BLOCK-D return)
ENC_DATA[1] (SIG-BLOCK-D return)	27	28	GND
GND	29	30	ENC_DATA[0] (SIG-BLOCK-D return)

Note: Signal grouping and GND interleaving rationale is documented in Stack-Interposer/Design_Spec.md §3. SIG-BLOCK-A occupies pins 1–12 (top half), SIG-BLOCK-D occupies pins 19–30 (bottom half), both interleaved with GND. TTD (SIG-BLOCK-E) appears on pins 13 and 18, with GND on pins 14 and 17. ACTUATE_REQUEST (SIG-BLOCK-G/H, per DEC-093) occupies pins 15/16. SIG-BLOCK-G carries the forward pass (this mini-stack's own Rotor chain, collected via Stack-Output, forwarded to Stack-Input); SIG-BLOCK-H carries the return pass (from Stack-Input's rear connector, back through this mini-stack's chain via Stack-Output, in reverse).

Routing note (DR-SINT-04): The pin mapping is pin-to-pin (J1 pin n → J2 pin n). However, because J1 and J2 both face upward with their pin-1 ends facing each other, the physical trace routes on L2/L3 will need to be laid out as if mirrored — traces will cross as they run across the board. Rows are preserved (row 1 → row 1, row 2 → row 2). This is a PCB routing constraint only; the electrical mapping is unchanged. See Design_Spec.md §3.

---

Diagram Reference

See design/Diagrams/cypher-system-layout.drawio — page "Mini-Stack Front View" — and design/Diagrams/renders/03-Mini-Stack-Front-View.png for the front-elevation view of the Rotor Mini-Stack showing the Stack-Interposer Board position at the base.