Encoder Module Board Layout Visualisations

Status: In Review Project: Enigma-NG Author: Izzyonstage & GitHub Copilot Version: v.0.1.0 Associated Hardware Revision: Rev A Last Updated: 2026-08-14

1. Component Areas

TOP VIEW (L1) - 4-Layer / 2oz Copper
 __________________________________________________________________
|                                                                  |
|   [ J1 - 90-PIN plain-bits BtB PLUG ]  <--- Left edge            |
|                                                                  |
|   [ SINGLE CPLD + DIGITAL DEBOUNCE / ROLE LOGIC ]                |
|   (EPM570T100I5N + sampled encode/decode image implementation)   |
|                                                                  |
|   [ J2 - 24-PIN cypher-bits+JTAG BtB PLUG ] <--- Bottom-right    |
|   [ J3 - 10-PIN POWER BtB PLUG ]            <--- Top-right       |
|                                                                  |
|   [ DATA PLATE ] <--- Inverted White Silkscreen on L4            |
|__________________________________________________________________|

2. Simplified Layout

____________________________________________________________
|                                                           |
|   [ J1 plain-bits ]     [ CPLD ]      [ J2 cypher-bits ]  |
|   (90-pin BtB plug)       (U1)      + JTAG (24-pin plug)  |
|                                        [ J3 power (10p) ] |
|___________________________________________________________|

1a. J1 - plain-bits Connector (DF40C-90DP-0.4V(51))

Connector Definition Owner: this board (canonical ENC-module BtB pin-mapping reference). Mates with the carrier board's DF40C-90DS receptacle. Reused by the Cypher Board (J7/J10/J13/J16), Cypher-Input Board (J1), and the future Cypher-Output Board.

2 rows x 45 positions = 90 total pins. 64 plain-bit signal pins (PB) + 26 GND pins, zig-zag distributed between rows (Bresenham-spread, max signal-only gap = 1 column between any two GND columns). PB[0] is leftmost (LSB convention).

Col	Row A	Row B
C01	PB[0]	PB[1]
C02	GND	PB[2]
C03	PB[3]	GND
C04	PB[4]	PB[5]
C05	GND	PB[6]
C06	PB[7]	PB[8]
C07	PB[9]	GND
C08	PB[10]	PB[11]
C09	GND	PB[12]
C10	PB[13]	GND
C11	PB[14]	PB[15]
C12	GND	PB[16]
C13	PB[17]	PB[18]
C14	PB[19]	GND
C15	PB[20]	PB[21]
C16	GND	PB[22]
C17	PB[23]	GND
C18	PB[24]	PB[25]
C19	GND	PB[26]
C20	PB[27]	PB[28]
C21	PB[29]	GND
C22	GND	PB[30]
C23	PB[31]	PB[32]
C24	PB[33]	GND
C25	PB[34]	PB[35]
C26	GND	PB[36]
C27	PB[37]	PB[38]
C28	PB[39]	GND
C29	GND	PB[40]
C30	PB[41]	PB[42]
C31	PB[43]	GND
C32	PB[44]	PB[45]
C33	GND	PB[46]
C34	PB[47]	PB[48]
C35	PB[49]	GND
C36	GND	PB[50]
C37	PB[51]	PB[52]
C38	PB[53]	GND
C39	PB[54]	PB[55]
C40	GND	PB[56]
C41	PB[57]	PB[58]
C42	PB[59]	GND
C43	GND	PB[60]
C44	PB[61]	PB[62]
C45	PB[63]	GND

plain-bits usage: all 64 PB[] positions are generic; how a carrier board wires them (to keyswitches, lightboard lamps, or plugboard jack terminals) is defined entirely by the carrier board's own design files - see e.g. Cypher-Input/Board_Layout.md §1. On Cypher-Input, all 64 positions are reserved exclusively for cipher-path keyswitches - LED colour selection is generated entirely on the carrier board itself and never touches this bus (see Cypher-Input/Design_Spec.md §5).

1b. J2 - cypher-bits + JTAG Connector (DF40C-24DP-0.4V(51))

Connector Definition Owner: this board. Mates with the carrier board's DF40C-24DS receptacle.

2 rows x 12 positions = 24 total pins. 12 signal pins + 12 GND pins, full zig-zag (every signal flanked by GND at adjacent columns). Signal order left-to-right: CB[0:5], then JTAG (TCK, RST_N, TMS, TDI, TDO), then ENC_ACTIVE_N.

Col	Row A	Row B
C01	CB[0]	GND
C02	GND	CB[1]
C03	CB[2]	GND
C04	GND	CB[3]
C05	CB[4]	GND
C06	GND	CB[5]
C07	TCK	GND
C08	GND	RST_N (CPLD_RESET_N)
C09	TMS	GND
C10	GND	TDI
C11	TDO	GND
C12	GND	ENC_ACTIVE_N

This board's usage: all 12 signals active. ENC_ACTIVE_N direction is role-dependent (KBD_ENC drives it, LBD_DEC consumes it, other roles hold it inactive/HIGH) - see Design_Spec.md §3. BRIGHTNESS_PWM (an external 555 oscillator on the carrier board, where applicable) feeds the CPLD GCLK0 pin - a dedicated clock input, not part of this 24-pin signal/JTAG connector.

1c. J3 - Power Connector (DF40C-10DP-0.4V(51))

Connector Definition Owner: this board. Mates with the carrier board's DF40C-10DS receptacle.

2 rows x 5 positions = 10 total pins. Power only, no zig-zag (solid rows). Row A = 3V3_ENIG, Row B = GND.

Col	Row A	Row B
C01	3V3_ENIG	GND
C02	3V3_ENIG	GND
C03	3V3_ENIG	GND
C04	3V3_ENIG	GND
C05	3V3_ENIG	GND

Pin-1 marker (per GRS §7.1): J1/J2/J3 pin 1 shall each be identified by a triangular silkscreen marker adjacent to the pin-1 corner on L1 per design/Standards/Global_Routing_Spec.md §7.1.

Power capacity: 5 x 3V3_ENIG pins x 1 A/pin = 5.0 A. One Encoder Module estimated load ~104 mA (1x EPM570 CPLD + 1x status LED + local margin) - substantial connector margin.

---

4. U1 - Encoder CPLD Signal Map (Logical Pin Budget)

This is the board-authoritative logical signal map for U1. The local MAX II handbook confirms EPM570T100 package availability in TQFP-100, but it points printed device pin-outs to external package documentation rather than embedding a fixed package pin table. The map below therefore freezes the required board-level connectivity while leaving the exact TQFP pad numbers to schematic capture.

Detailed role logic, sampled debounce requirements, and encoder/decoder behaviour are owned by design/Software/CPLD_Logic/Encoder_Logic.md.

4.1 Dedicated device pins

Function	Source / destination	Notes
TCK	J2 C07 (Row A) -> U1	Dedicated JTAG clock input
TMS	J2 C09 (Row A) -> U1	Dedicated JTAG mode input
TDI	J2 C10 (Row B) -> U1	Dedicated JTAG serial input from the carrier board's JTAG chain
TDO	U1 -> R6 -> J2 C11 (Row A)	Dedicated JTAG serial output back to the carrier board's JTAG chain
DEV_CLR_N / reset input	J2 C08 (Row B, RST_N/CPLD_RESET_N) -> U1	Active-low device reset; held high locally by R5 (vendor pin name DEV_CLRN - see design/Standards/Global_Routing_Spec.md §10)

4.2 General-purpose signal groups

Signal group	Pins	U1 direction	Notes
J1 PB[0:63] plain-bits bank	64	Role-dependent	Encode-role population reads one asserted line; decode-role population drives one-of-64 output
J2 CB[0:5] cypher-bits	6	Role-dependent	Encode role drives the 6-bit bus back to the carrier board; decode role consumes it
ENC_ACTIVE_N	1	Role-dependent	KBD_ENC drives keyboard activity LOW when a debounced key is active; LBD_DEC consumes it to blank outputs when idle; other roles keep it inactive
D1 status LED	1	Output	Active-low debug LED: U1 drives LOW to illuminate

Logical budget summary: 72 general-purpose signal connections total = 64 bank lines + 6 bus lines + 1 activity sideband + 1 LED, plus the dedicated JTAG / reset pins above.

Spare-pin policy: the active docs do not currently claim any spare U1 user I/O.

---

5. Routing - Trace Width Specifications

Board specs: 4-layer / 2oz finished copper — stackup per GRS §2.3.1.
L1 = signal (JTAG/routing); L2 = GND plane; L3 = 3V3_ENIG power pour; L4 = secondary routing / data plate.

IPC-2221A basis (2oz copper, external, 10°C rise, 25°C ambient):
For 2oz external: ~0.15 mm/A. The 3V3_ENIG inner pour (L3) handles board load without width constraints. See Global_Routing_Spec.md §1.1 for the full current-category table.

Encoder Module current budget:
1x EPM570T100I5N CPLD @ 50 mA; 1x status LED @ 4 mA; misc = ~50 mA; total worst-case: 104 mA from the 3V3_ENIG rail supplied via J3.

5.1 Trace Width Table

Net	Peak Current	IPC Calc (2oz ext)	Design Min	Specified Width	Layer	Notes
Signal (plain-bits, cypher-bits)	< 5 mA	< 0.001 mm	per GRS §1.1	per GRS §1.1	L1	3.3 V logic; CPLD I/O; J1/J2 traces
JTAG signals: TCK, TMS, TDI, TDO (CI)	signal	-	per GRS §2.3.1	per GRS §2.3.1 / JLCPCB_Manufacturing.md §1.1	L1 (external)	50 Ω controlled impedance over L2 GND plane; per DEC-016
3V3_ENIG power (J3 -> CPLD + LED)	104 mA	0.016 mm	per GRS §1.1	per GRS §1.1	L1 + L3 pour	Canonical 3V3_ENIG width per GRS §1.1
3V3_ENIG distribution (inner power pour)	104 mA	-	pour	copper pour	L3	Full uninterrupted 2oz plane
GND return (inner GND pour)	-	-	pour	copper pour	L2	Reference plane under all CI traces on L1

5.2 Notes

• JTAG CI traces: 50 Ω controlled impedance on L1 over the L2 GND plane. Trace width per GRS §2.3.1 and design/Production/JLCPCB_Manufacturing.md §1.1.
• Cable-output trace (U1 TDO -> R6 -> J2 C11): R6 (75 Ω) is placed within 2 mm of U1 TDO; the post-R6 trace to the J2 connector pad should be kept short.
• 3V3_ENIG power entry (J3, all 5 Row A pins): power pins connect to the same L3 copper pour via thermal vias; L1 traces from J3 to the via entry points per GRS §1.1.