[bot]
server: localhost
#	This is the adress, where the moonraker of the desired printer is located at. 
#	In most cases it will be 'localhost'. Alternatively, an ip:port, as in 192.168.0.19:7125 can be entered, 
#	if you are running multiple moonraker instances on the machine, or if the bot is located not on the printer itself.
#	This value is not validated automatically.
bot_token: xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
#	This is the bot token. Please keep it safe and do not post it online.
#	Only the chat with the correct chat_id can send/receive commands to/from the bot.
#	Alternatively can be stored in a file. See [secrets] section.
#	This value is not validated automatically.
chat_id: xxxxxxxxx
#	This is the ID of the chat, where the bot is supposed to be able to send updates to. 
#	Alternatively can be stored in a file. See [secrets] section.
#	This value should be an integer.
#api_url: https://api.telegram.org/bot
#	If you need it, you can specify a custom url for the telegram API.
#	This value is not validated automatically.
#socks_proxy: 192.168.0.22:1080
#	If needed, you can configure the bot to use a socks5 proxy.
#	This value is not validated automatically.
#user: root
#	If you have moonraker authorization enabled, you can enter the user and password here.
#	My advice is to not expose your printer to the internet, but I am not your mother.
#	Alternatively can be stored in a file. See [secrets] section.
#	This value is not validated automatically.
#password: qwerty
#	The password is stored in plain text.
#	Alternatively can be stored in a file. See [secrets] section.
#	This value is not validated automatically.
#api_token: 86c4841ec730415da0a66064ceeaa99c
#	As an alternative to the password you can use a token.
#	Alternatively can be stored in a file. See [secrets] section.
#	This value is not validated automatically.
#light_device: leds
#	This is the power device in moonraker, to which the lights of the printer/chamber are connected to.
#	If you do not have lights/have no need to cycle them, skip this parameter.
#	Default is to omit this.
#	This can be a klipper output_pin or a macro as well. Refer to moonrakers "klipper_device" documentation.
#	This parameter will be derpeciated in coming updates.
#power_device: power
#	This is the power device in moonraker, to which the power of the printer slave boards are connected to.
#	A typical usage scenario is to shutdown power to the MCUs, but not to disable the host on which klipper is running.
#	If you do not have such a setup, skip this.
#	Default is to omit this.
#	This parameter will be derpeciated in coming updates.
#debug: false
#	This enables extensive logging. Only use it for debugging/troubleshooting.
#	Default is to omit this/false.
#	This value should be boolean.
#upload_path: myfolder/mysubfolder
#	This determines, to which folder the bot will upload the gcodes sent to it. 
#	Default is to use the base gcode folder.
#	Any path entered is relative from the klippers gcode folder.
#	This value is not validated automatically.

[camera]
host: http://localhost:8080/?action=stream
#	This is the adress, where the desired webcam/webstream is located at. Enter this the same way you enter it in 
#	your printers web interface/your player. If you can stream it, the bot supports it, native h264 streams,
#	for example a vlc stream from a runcam webcam is absolutely possible. Do not feel contstrained by mjpeg streams.
#	This value is not validated automatically.
#fps: 30
#	If you want to use the "/video" button/command, you should set the camera fps. Not set by default.
#	This value should be a positive integer >0.
#flip_vertically: false
#	You can flip the camera image vertically, if needed. Disabled by default. Set to true if needed.
#	This value should be boolean.
#flip_horizontally: false
#	You can flip the camera image horizontally, if needed. Disabled by default. Set to true if needed.
#	This value should be boolean.
#rotate: 90_cw
#	You can rotate the camera image, if needed. Disabled by default.
#	Allowed values: 90_cw, 90_ccw, 180. Default behaviour is not to rotate the image.
#fourcc: x264
#	You can change the opencv VideoWriter fourcc codec. The default value is 'x264'.
#	Allowed values: x264, mp4v
#	If you need specific codec support, please open an issue.
#threads: 2 
#	You may limit the threads used for image processing. Default value is calculalated, (os.cpu_count() / 2)
#	This value should be and integer >0 and < os.cpu_count().
#video_duration: 5
#	This is the length in seconds of the video, which is sent when requested with /video command. 
#	Default length of a video is 5 seconds
#	This value should be a positive integer >0.
#video_buffer_size: 2
#	On most single-board computers the renderer does not manage to capture and process frames fast enough for a video.
#	If you are getting shorter videos than you requested in video_duration and have free RAM, you can increse this value.
#	Be careful - 1 uncompressed captured image weights about 6mb when in fullHD.
#	OpenCV libraries have a limit of 2 GB, so please calculate your maximum available buffer from your fps and resolution.
#	This value should be a positive integer >0.
#light_control_timeout: 0
#	When the bot toggles lights to take a picture, or record a video, most cameras need a couple of seconds to adjust to 
#	the transition between full darkness and full brightness. This option tells the bot to wait n seconds, before
#	taking the picture, recording a video, doing timelapse photos. The default is not to use a delay.
#	This value should be an integer >=0.
#picture_quality: high
#	This parameter controls the picture quality the bot uses for status and timelapse purposes. 
#	Allowed values: low, high	
#	Low uses jpeg with quality set to 80, high uses losless webp.
#	Default is "high"

#[secrets]
#secrets_path: /home/pi/printer_data/config
#	Set the full path to your secrets.conf here. Secrets.conf needs to be readable for the user under which the bot is running.
#	This value is not validated automatically.

[secrets] 
#bot_token:
#chat_id:
#user:
#password:
#api_token:

#[progress_notification]
#percent: 0
#	This is an interval in percent, when a notification with a picture is sent to the chat.
#	When set to 5, notifications are sent at 5%, 10%, 15%, etc.
#	When set to 3, notifications are sent at 3%, 6%, 9%, etc.
#	The default is not to send notifications based on print percentage.
#	This value should be an integer >=0.
#height: 0.0
#	This is an interval in mm, when a notification with a picture is sent to the chat.
#	When set to 5.0, notifications are sent at 5.0mm, 10.0mm, 15.0mm, etc, print height.
#	When set to 0.25, notifications are sent at 0.25mm, 0.5mm, 0.75mm, etc, print height.
#	The default is not to send notifications based on print height.
#	This value should be an float >=0.0.
#time: 0
#	This is the recommended way to use progress notifications.
#	This is an interval in seconds, when a notification with a picture is sent to the chat.
#	When set to 600, notifications are sent at 600 seconds, 1200 seconds, 1800 seconds, etc, print time.
#	When set to 100, notifications are sent at 100 seconds, 200 seconds, 300 seconds, etc, print time.
#	The default is not to send notifications based on time.
#	This type of notifications continues, even when the print is paused. So if your printer triggers a pause, for example 
#	caused by filament runout, you will still get notifications regularly, until the print is completed/canceled.  
#	This value should be an integer >=0.
#groups: group_id_1, group_id_2
#	When running multiple printers/a farm, you may want to aggregate all notifications from all printers in a group.
#	You can enter group IDs here, to which notifications will be sent. No control from a group is possible.
#	Only notifications are sent.
#	Telegram group IDs are negative integers.
#	This should be a list of integers.
#group_only: false
#	If you are using the group feature, you might want to disable individual notifications and use group notifications only.
#	Set this to true to disable individual notifications in individual chats.
#	This value should be boolean.

[timelapse]
#basedir: ~/moonraker-telegram-bot-timelapse
#	This sets the folder, where to save timelapse pictures and the resulting video. 
#	Default is '~/moonraker-telegram-bot-timelapse', but you can set it to any catalog, which the bot 
#	has rights to write to. Might be useful for saving the sd cards life by writing to external storage.
#	This value is not validated automatically.
#copy_finished_timelapse_dir: /home/pi/timelapse/finished
#	This sets the folder, to which finished timelapses get copied to. 
#	The default behaviour is not to copy it anywhere. This might be useful, if you want to keep only the videos, 
#	but clean up the pictures, or if you want to upload the videos to some network location.
#	This value is not validated automatically.
#cleanup: true
#	Should the bot clean the catalog with pictures and video after the successful sending to the telegram chat.
#	Default is true. You might want to set it to false, if you intend on using the pictures later.
#	This value should be boolean.
#height: 0
#	The bot can take timelapse pictures based on the z axis height (e.g. 0.2). The default is not to take pictures based on height.
#	This value should be an float >=0.0.
#time: 0
#	The bot can take timelapse pictures based on time intervals in seconds. 
#	The default is not to take pictures based on time intervals.
#	This value should be an integer >=0.
#target_fps: 15  
#	This is the target fps of the created video. The larger this number, the "faster" the timelapse will be.
#	15 fps equals 15 images per second lapsing. The default is 15 fps.
#	This value should be an integer >0.
#min_lapse_duration: 0
#	On short prints, or with limited lapse pictures available, the lapse often gets to short to meaningfully display
#	the printing progress. You can specify the desired minimum duration of the created timelapse 
#	(not including last_frame_duration). This means, that the fps will get reduced, if the lapse is shorter than this time.
#	The default is to omit this. 
#	This value should be an integer >0 and <max_lapse_duration
#max_lapse_duration: 0
#	Similar to min_lapse_duration, if your lapse video gets too long to watch, you can specify a desired time, which
#	should not be exceeded. This means, that the fps will get increased, if the lapse is going to be longer than this time.
#	The default is to omit this. 
#	This value should be an integer >0 and >min_lapse_duration
#last_frame_duration: 5
#	This allows you to prevent the timelapse video from ending too abruptly. You can choose a duration for which 
#	to loop the last picture taken.
#	Default is 5 seconds. 
#	This value should be an integer >=0.
#after_lapse_gcode: /my_macro
#	You can run a macro or a gcode (e.g /gcode %your gcode here%) after the bot finishes building the timelapse.
#	This may be useful, if you intend shutting down the printer, if you want to automatically start another print,
#	or if you want to do something with the video after its ready. 
#	This value is not validated automatically.
#send_finished_lapse: true
#	If you want to build the lapse, but do not want to send it, set this to false. Default is true.
#	This value should be boolean.
#manual_mode: false
#	If True, only commands from gcode will manage timelapse.
#	Default is false.
#	This value should be boolean.
#after_photo_gcode: 
#	You can enter any macro or gcode to be run after the "photo_and_gcode" command.
#	Default is not to run any gcode after the command.
#	This value is not validated automatically.

[telegram_ui]
#eta_source: slicer
#	You can choose, which value to use for remaining time estimation.
#	Default value is slicer.
#	Allowed values: slicer, file
#buttons: [status,pause,cancel,resume],[files,emergency,macros,shutdown]
#	You can redefine, which buttons and in which position you want displayed.
#	If this is not defined, the default order is used. Buttons are defined per row, each row separated.
#	This allows you to add your own custom macros to the bot's keyboard as well. 
#	Add or replace default bot commands with "/%macro_name%. The macro listed in this section
#	should be defined in klipper config files, in UPPERCASE. Maximum macro name length is 54 chars.
#	This value is not validated automatically.
#require_confirmation_macro: true
#	This parameter makes the bot confirm, if you want to run a macro, similar to the check which happens 
#	with the "/shutdown" command.
#	Default is true.
#	This value should be boolean.
#progress_update_message: false
#	Every time status gets updated, a notification message is sent, that the progress status has been updated.
#	It gets deleted after the next status update is triggered. Setting it to false will not send notifications on progress updates.
#	Default is false.
#	This value should be boolean.	
#silent_progress: false
#	If progress_update_message is set to true, setting this to "true" sends the printer status change without an alert. 
#	You still get a "red" notification. Sadly the bot API does not permit sending "grey" completely silent messages. 
#	There is no way to work around that. 
#	Default is false.
#	This value should be boolean.
#silent_commands: false
#	Sends all other messages (for example the emergency stop confirmation) without an alert.You still get a "red" notification, 
#	but it does not have sound or vibration.
#	Sadly the bot API does not permit sending "grey" completely silent messages. There is no way to work around that. 
#	Default is false.
#	This value should be boolean.
#silent_status: false
#	Sends the printer status change (error, idle etc.) without an alert. You still get a "red" notification, 
#	but it does not have sound or vibration.
#	Sadly the bot API does not permit sending "grey" completely silent messages. There is no way to work around that. 
#	Default is false.
#	This value should be boolean.
#include_macros_in_command_list: true
#	This enables in-chat autocomplete for macros. 
#	Default is true. 
#	Telegram can not handle autocompletion for commands longer than 32 symbols. Macro names which exceed this length will not get autocompleted.
#	This value should be boolean.
#hidden_macros: macro1, macro2
# 	If you have macros displayed in the auto-complete list, you may want to hide specific ones.
#	Default is not to hide any macros.
#	This value is not validated automatically.
#hidden_bot_commands: bot_restart, cancel, video
#	You may want to hide specific commands of the bot from the auto-complete list.
#	Default is not to hide any commands.
#	This value is not validated automatically.
#show_private_macros: false
#	You can decide to show service macros prefaced with a "_" in the autocomplete list.
#	Default is to hide and not autocomplete these macros.
#	This value should be boolean.
#status_message_m117_update: false
#	If you want, you can trigger a status update on the m117 command.
#	Default is not to trigger an update.
#	This value should be boolean.

#[status_message_content]
#content: progress, height, filament_length, filament_weight, print_duration, eta, finish_time, m117_status, tgnotify_status, last_update_time
#	This controls the content of the status message. You can choose to delete specific information not relevant to you.
#	Most of those parameters are self-explanatory. m117_status leaves a line to display text from the M117 gcode.
#	tgnotify_status is used to display custom information by sending the corresponding G-Code command, refer to interacting with klipper.md
#	last_updated_time displays the time, when the status message content was last updated when using status_single_message.
#	Allowed values: progress, height, filament_length, filament_weight, print_duration, eta, finish_time, m117_status, tgnotify_status, last_update_time
#sensors: mcu, ..., ...
#	You can add temperature sensors, like the "mcu" sensor to be displayed in the status message. 
#	Enter the names from your klipper config, separated by commas.
#	Default is not to display any additional temperature sensors.
#	This value is not validated automatically.
#heaters: extruder, heater_bed
#	You can add heaters, like the extruder, or the bed to be displayed in the status message. 
#	Enter the names from your klipper config, separated by commas.
#	Default is not to display any additional heaters. 
#	This value is not validated automatically.
#fans: your_fan, your_fan2
#	You can add any fans you have in the clipper config to be displayed in the status message. 
#	Enter the names from your klipper config, separated by commas.
#	Default is not to display any additional fans.
#	This value is not validated automatically.
#moonraker_devices: light, psu
#	You can add moonraker power devices to be displayed on the status message.
#	Enter the names from your moonraker config, separated by commas.
#	Default is not to display any additional devices. 
#	This value is not validated automatically.