20160602_jeffrey - silenceuncrio/diary GitHub Wiki
Index
0835
m300
來試一下 MfgTool
先從官網下載 L3.14.52_1.1.0_ga-mfg-tools.tar.gz
... 快 500MB
4.2.2 Using MfgTool
Follow these instructions to use the MfgTool V2:
- Connect a USB cable from a computer to the USB OTG port on the board.
- Connect a USB cable from the OTG-to-UART port to the computer for console output.
這裡的 the OTG-to-UART port
指的其實是 i.MX6UL EVK board 上的 Debug USB
接上電腦(window10)後會多出一個 COMX port, 我都使用 Tera Term
- 115200baud 來看 debug information
這邊的 USB OTG port
是板子上的 USB OTG(USB OTG1)
記得 i.MX 6UltraLite EVK DIP switch(SW602) 要切換成 Serial Downloader
模式
不然 MfgTool 會找不到 device
切成 Serial Downloader
後 MfgTool 的畫面如下
我們之後自己的板子 USB OTG1 的接頭會改成一般的 USB 母頭
所以會少一根 ID pin
目前 morris 的作法是將該 pin 拉出來利用點組來控制 pull high 或 pull low
目前的推論是不會影響到 MfgTool 的使用
因為切換成 Serial Downloader
模式時, i.MX 6UltraLite 上沒有 Linux 也沒有 U-Boot 的存在
此時 PC 上的 MfgTool 就能認出 Device 了
所以 i.MX 6UltraLite 內部肯定有甚麼 driver 在運作
到時候等我們自己的板子回來之後一試便知道了
最糟就 ID pin 上的 pull high 或 pull low 切換一下
1025
來玩 ELECTRON
說真的... 太新了... 文件實在不多
很炫... 但並不說非它不行
1300
survey 一下 visual basic
目前比較跟上潮流的並不是 Visual Basic 而是 C#
參考 小山的 C# 教學-特別篇-簡單介紹 Visual Studio 2015 Express
安裝 Visual Studio Express 2015 for Window Desktop
1335
等待安裝的同時先盤一下 m300 截至七月中為止的 schedule
Features | Schedule | Resource |
---|---|---|
u-boot : FLASH layout | 7月15日 | Jeffery |
u-boot : burn image | 7月15日 | Jeffery |
u-boot : Reduce image size | 7月15日 | Jeffery |
EMMC/NAND MTD Driver | 7月15日 | Jeffery |
七月中前我必須完成的項目計有下述四項
- u-boot : FLASH layout
- u-boot : burn image
- u-boot : Reduce image size
- EMMC/NAND MTD Driver
但不能每一項都要等到七月中才完成, 來排個先後順序
- u-boot : FLASH layout
- u-boot : burn image
- u-boot : Reduce image size
- EMMC/NAND MTD Driver
拆成小項目再讓每個禮拜都有階段性目標可完成
Features | Schedule | Status |
---|---|---|
u-boot : burn image - SD Card | 6月3日 | 已完成 |
u-boot : Reduce image size | 6月10日 | |
u-boot : image layout - SD Card | 6月17日 | |
u-boot : image layout - NAND Flash | 6月24日 | |
EMMC/NAND MTD Driver | 7月1日 | |
u-boot : burn image - NAND Flash | 7月8日 |
email 給 ariel... 收工
1420
明天可以請一天公假去看 computex
下班前再發 mail 吧