EK‐RA6M5 Sample and Demo Hardware configuration - renesas/zephyr GitHub Wiki

Followings are hardware connection and test samples for EK-RA6M5, for more detail on 1st setup hardware connection, please visit EK-RA6M5 - Quick Start Guide and EK-RA6M5 v1 - User's Manual

Default HW configuration:

Zephyr UART Console setting: EK-RA6M5 board require to connect with a USB UART board to communicate with PC console

e.g. PMOD USB UART

Pin configuration:

Board	Channel	Board Pin function	Board Pin	Connect to PMOD 2
EK-RA6M5	SCI0	TXD0	P411 (PMOD 2)	USB UART RXD pin
		RXD0	P410 (PMOD 2)	USB UART TXD pin
		GND	GND	USB UART GND pin
		P3.3V	VCC	USB UART VCC pin

Hardware connection for UART samples

echo_bot (samples/drivers/uart/echo_bot):
- Hardware configuration: No additional connection.
- Build command:
```
west build -p always -b ek_ra6m5 samples/drivers/uart/echo_bot/
```
zTest uart_basic_api (tests/drivers/uart/uart_basic_api):
- Hardware configuration: No additional connection.
- Build command:
```
west build -p always -b ek_ra6m5 tests/drivers/uart/uart_basic_api/
```
zTest uart_async_api (tests/drivers/uart/uart_async_api):
- Hardware configuration: Loopback for TXD and RXD
  
  Board Channel Pin function Pin Connect to
  
  EK-RA6M5 SCI7 TXD7 P613 Loopback to RXD9 pin
  
  RXD7 P614 Loopback to RXD9 pin
- Build command:
```
west build -p always -b ek_ra6m5 tests/drivers/uart/uart_async_api/
```

Board	Channel	Pin function	Pin	Connect to
EK-RA6M5	SCI7	TXD7	P613	Loopback to RXD9 pin
		RXD7	P614	Loopback to RXD9 pin

Hardware connection for SPI samples

spi_bitbang (samples/drivers/spi_bitbang): Loopback for MISO and MOSI
Note: The purpose of testing sample spi_bitbang on RA boards is to provide users with an understanding of the RA SPI driver. To test this sample using the SPI hardware IP, you can configure it by adding the overlay and configuration files with the following content:

samples/drivers/spi_bitbang/boards/ek_ra6m5.conf
```
CONFIG_STDOUT_CONSOLE=y
CONFIG_SPI=y
CONFIG_SPI_B_INTERRUPT=y
CONFIG_SPI_B_RA_DTC=y
CONFIG_LOG=y
CONFIG_SPI_BITBANG=n
```
- Note: We have to disable the CONFIG_SPI_BITBANG since we use SPI hardware IP to test spi_bitbang.
  
  samples/drivers/spi_bitbang/boards/ek_ra6m5.overlay
```
 spibb0: &spi0 {
   		rx-dtc;
   		tx-dtc;
   		pinctrl-0 = <&spi0_default>;
   		pinctrl-names = "default";
   		cs-gpios = <&ioport4 13 GPIO_ACTIVE_LOW>; // dummy config
   		status = "okay";
   	};

 &ioport4 {
   		status = "okay";
 };
```
- Hardware configuration:
  
  Board Channel Pin function Pin Connect to
  
  EK-RA6M5 SPI0 MISO0 P202 Loopback to MOSI0
  
  MOSI0 P203 Loopback to MISO0
- Build command:
```
west build -p always -b ek_ra6m5 samples/drivers/spi_bitbang
```
zTest spi_loopback (tests/drivers/spi/spi_loopback)
- Hardware configuration: Loopback for MISO and MOSI
  
  Board Channel Pin function Pin Connect to
  
  EK-RA6M5 SPI0 MISO0 P202 Loopback to MOSI0
  
  MOSI0 P203 Loopback to MISO0
- Build command:
```
west build -p always -b ek_ra6m5 samples/drivers/spi_bitbang
```

Board	Channel	Pin function	Pin	Connect to
EK-RA6M5	SPI0	MISO0	P202	Loopback to MOSI0
		MOSI0	P203	Loopback to MISO0

Board	Channel	Pin function	Pin	Connect to
EK-RA6M5	SPI0	MISO0	P202	Loopback to MOSI0
		MOSI0	P203	Loopback to MISO0

Hardware connection for I2C sample

zTest i2c_api (tests/drivers/i2c/i2c_api):
- Hardware configuration: Require GY-271 QMC5883L module
  
  Board Channel Pin function Pin Connect to GY-271 QMC5883L module
  
  EK-RA6M5 RIIC1 SCL1 P512 SCL
  
  SDA1 P511 SDA
  
  P3V3 P3V3 VCC
  
  GND GND GND
  
  - - DDBY
- Build command:
```
west build -p always -b ek_ra6m5 tests/drivers/i2c/i2c_api
```

Board	Channel	Pin function	Pin	Connect to GY-271 QMC5883L module
EK-RA6M5	RIIC1	SCL1	P512	SCL
		SDA1	P511	SDA
		P3V3	P3V3	VCC
		GND	GND	GND
		-	-	DDBY

Hardware connection for Flash samples

zTest flash common (tests/drivers/flash/common): No additional connection.
- Hardware configuration: No additional connection.
- Build command:
```
west build -p always -b ek_ra6m5 tests/drivers/flash/common
```

Hardware connection for ADC samples

zTest adc_api (tests/drivers/adc/adc_api): No additional connection.
- Hardware configuration: No additional connection.
- Build command:
```
west build -p always -b ek_ra6m5 tests/drivers/adc/adc_api
```
zTest adc_accuracy_test (tests/drivers/adc/adc_accuracy_test):
- Hardware configuration: Loopback 3V3 and AN000 (P000).
- Build command:
```
west build -p always -b ek_ra6m5 tests/drivers/adc/adc_accuracy_test
```

Hardware connection for PWM (GPT) samples

zTest pwm_api (tests/drivers/pwm/pwm_api): No additional connection.
- Hardware configuration: No additional connection.
- Build command:
```
west build -p always -b ek_ra6m5 tests/drivers/pwm/pwm_api
```
zTest pwm_loopback (tests/drivers/pwm/pwm_loopback):
- Hardware configuration: Loopback 2 channels (1 PWM output, 1 PMW capture)
  
  Board Channel Pin Pin function Remark
  
  EK-RA6M5 PWM1 P405 GTIOC1A PWM output, loopback to PWM capture pin
  
  PWM4 P302 GTIOC4A PWM capture, loopback to PWM output pin
- Build command:
```
west build -p always -b ek_ra6m5 tests/drivers/pwm/pwm_loopback
```

Board	Channel	Pin	Pin function	Remark
EK-RA6M5	PWM1	P405	GTIOC1A	PWM output, loopback to PWM capture pin
	PWM4	P302	GTIOC4A	PWM capture, loopback to PWM output pin

Hardware connection for Counter (AGT) samples

Counter Alarm sample (samples/drivers/counter/alarm):
- Hardware configuration: No additional connection.
- Build command:
```
west build -p always -b ek_ra6m5 samples/drivers/counter/alarm`
```

Hardware connection for USB samples

USB HS Device:
- Hardware configuration: For a USB Device configuration, set Jumper J7 to pins 2-3, install a jumper on J17 pins 1-2, connect USB HS Port (J31) to a host PC.
- Build command
  - USB Mass Storage (samples/subsys/usb/mass):
```
west build -p always -b ek_ra6m5 samples/subsys/usb/mass -DCONF_FILE=usbd_next_prj.conf -DDTC_OVERLAY_FILE=ramdisk.overlay
```
  - USB CDC-ACM (samples/subsys/usb/cdc_acm):
```
west build -p always -b ek_ra6m5 samples/subsys/usb/cdc_acm -DCONF_FILE=usbd_next_prj.conf
```
  - ztest udc (tests/drivers/udc):
```
west build -p always -b ek_ra6m5 tests/drivers/udc/
```
USB FS Device:
- Hardware configuration: For a USB Device configuration, set jumper J12 to pins 2-3, install a jumper on J15 pins 1-2, connect USB FS Port (J11) to a host PC.
- Build command
  - USB Mass Storage (samples/subsys/usb/mass):
```
west build -p always -b ek_ra6m5 samples/subsys/usb/mass -DCONF_FILE=usbd_next_prj.conf -DDTC_OVERLAY_FILE=ramdisk.overlay
```
  - USB CDC-ACM (samples/subsys/usb/cdc_acm):
```
west build -p always -b ek_ra6m5 samples/subsys/usb/cdc_acm -DCONF_FILE=usbd_next_prj.conf
```
  - ztest udc (tests/drivers/udc):
```
west build -p always -b ek_ra6m5 tests/drivers/udc/
```

Note: You need to replace the the USB HS node in zephyr/boards/renesas/ek_ra6m5/ek_ra6m5.dts with below define for USB FS

&usbfs {
	pinctrl-0 = <&usbfs_default>;
	pinctrl-names = "default";
	maximum-speed = "full-speed";
	status = "okay";
	zephyr_udc0: udc {
		compatible = "renesas,ra-udc";
		status = "okay";
		cdc_acm_uart0 {
			compatible = "zephyr,cdc-acm-uart";
		};
	};
};

Hardware connection for DAC samples

ztest dac_api (tests/drivers/dac/dac_api):
- Hardware configuration: No additional connection.
- Build command: west build -p always -b ek_ra6m5 tests/drivers/dac/dac_api
DAC sample (samples/drivers/dac):
- Hardware configuration: No additional connection.
- Build command: west build -p always -b ek_ra6m5 samples/drivers/dac