vrf_selection_multi_linecard_test - openconfig/featureprofiles GitHub Wiki
On a modular DUT, a VRF selection policy bound to several ingress interfaces must be programmed into the forwarding hardware of every linecard (and every forwarding integrated circuit) hosting one of those interfaces. This test dynamically discovers the parent LINECARD component for each reserved port (port1..port8), requires at least 2 distinct linecards across the testbed (using up to 3 distinct ingress linecards LC_INGRESS when available), and builds up in stages:
-
RT-3.6.1: Baseline 2-rule VRF selection policy (one IPv4, one IPv6) bound to physical ingress ports
port1..port3across the discovered ingress linecards. -
RT-3.6.2: In-place scale to 34 rules steering into 4 VRFs (
VRF-1..VRF-4) across 6 ingress interfaces (port1..port3and LACP aggregatesAgg-A..Agg-Conport5..port7). - RT-3.6.3: In-place rule modification propagation across all linecards without stale hardware entries.
- RT-3.6.4: Physical ingress port and LACP member port flap persistence on each linecard.
- RT-3.6.5: Single-linecard cold reboot on each discovered ingress linecard (1 iteration per linecard) while traffic runs hitlessly on any un-rebooted linecards.
- RT-3.6.6: Linecard boot with concurrent policy rule and interface binding updates before the booting linecard's aggregate interface comes up (1 iteration per ingress linecard).
- RT-3.6.7: Simultaneous multi-linecard cold reboot (Part A, 1 iteration) and full DUT cold reboot with configuration persistence (Part B, 1 iteration).
- RT-3.6.8: In-place policy replace and 5-iteration interface unbind/rebind churn across all 6 ingress interfaces.
-
RT-3.6.9: Per-linecard forwarding ASIC (
INTEGRATED_CIRCUIT) resource utilization telemetry and cross-linecard symmetry. -
RT-3.6.10: Negative configuration and forwarding checks (
RT-3.6.10.1–RT-3.6.10.5).
Every traffic check is validated per ingress interface and per address family, distinguishing VRF-steered traffic from DEFAULT-routed traffic by egress port/subinterface.
graph LR
A1[ATE port-1] <-->|Ingress physical| D1[DUT port-1]
A5[ATE port-5] <-->|Ingress Agg-A member| D5[DUT port-5]
A2[ATE port-2] <-->|Ingress physical| D2[DUT port-2]
A6[ATE port-6] <-->|Ingress Agg-B member| D6[DUT port-6]
A3[ATE port-3] <-->|Ingress physical| D3[DUT port-3]
A7[ATE port-7] <-->|Ingress Agg-C member| D7[DUT port-7]
D4[DUT port-4] <-->|Egress VLAN 10-13 (VRF-1..VRF-4)| A4[ATE port-4]
D8[DUT port-8] <-->|Egress (DEFAULT)| A8[ATE port-8]
- Connect DUT
port1..port8to ATEport1..port8respectively. -
Ingress interfaces: physical ports
port1,port2,port3(from RT-3.6.1) and 1-member LACP aggregatesAgg-A(port5),Agg-B(port6),Agg-C(port7) (added in RT-3.6.2, allocated via the DUT's aggregate naming). -
Egress interfaces:
port4(VLAN subinterfaces forVRF-1..VRF-4, plusport4.20forDEFAULTin RT-3.6.1) andport8(DEFAULTfrom RT-3.6.2 onward). -
Linecard resolution & dynamic grouping precondition:
- For each port in
port1..port8, read/interfaces/interface/state/hardware-portand walk/components/component/state/parentup to 5 hops until/components/component/state/type == LINECARD. If noLINECARDcomponent exists, skip with"DUT has no LINECARD components; RT-3.6 requires a modular DUT". - Dynamically group
port1..port8by their discovered parentLINECARDcomponent (ALL_LCS = unique([LC(port1)..LC(port8)])andLC_INGRESS = unique([LC(port1), LC(port2), LC(port3), LC(port5), LC(port6), LC(port7)]), up to 3 distinct ingress linecards). Require at least 2 distinctLINECARDcomponents acrossport1..port8(len(ALL_LCS) >= 2); otherwise skip.
- For each port in
| DUT interface | Added in | Network instance | DUT IPv4 | ATE IPv4 | DUT IPv6 | ATE IPv6 |
|---|---|---|---|---|---|---|
port1 (subif 0) |
RT-3.6.1 | DEFAULT |
192.0.2.1/30 |
192.0.2.2 |
2001:db8:0:1::1/126 |
2001:db8:0:1::2 |
port2 (subif 0) |
RT-3.6.1 | DEFAULT |
192.0.2.5/30 |
192.0.2.6 |
2001:db8:0:2::1/126 |
2001:db8:0:2::2 |
port3 (subif 0) |
RT-3.6.1 | DEFAULT |
192.0.2.9/30 |
192.0.2.10 |
2001:db8:0:3::1/126 |
2001:db8:0:3::2 |
port4.10 (VLAN 10) |
RT-3.6.1 | VRF-1 |
192.0.2.13/30 |
192.0.2.14 |
2001:db8:0:4::1/126 |
2001:db8:0:4::2 |
port4.20 (VLAN 20) |
RT-3.6.1 (removed in RT-3.6.2) | DEFAULT |
192.0.2.17/30 |
192.0.2.18 |
2001:db8:0:5::1/126 |
2001:db8:0:5::2 |
Agg-A (subif 0; member port5) |
RT-3.6.2 | DEFAULT |
192.0.2.21/30 |
192.0.2.22 |
2001:db8:0:6::1/126 |
2001:db8:0:6::2 |
Agg-B (subif 0; member port6) |
RT-3.6.2 | DEFAULT |
192.0.2.25/30 |
192.0.2.26 |
2001:db8:0:7::1/126 |
2001:db8:0:7::2 |
Agg-C (subif 0; member port7) |
RT-3.6.2 | DEFAULT |
192.0.2.29/30 |
192.0.2.30 |
2001:db8:0:8::1/126 |
2001:db8:0:8::2 |
port8 (subif 0) |
RT-3.6.2 | DEFAULT |
192.0.2.33/30 |
192.0.2.34 |
2001:db8:0:9::1/126 |
2001:db8:0:9::2 |
port4.11 (VLAN 11) |
RT-3.6.2 | VRF-2 |
192.0.2.37/30 |
192.0.2.38 |
2001:db8:0:a::1/126 |
2001:db8:0:a::2 |
port4.12 (VLAN 12) |
RT-3.6.2 | VRF-3 |
192.0.2.41/30 |
192.0.2.42 |
2001:db8:0:b::1/126 |
2001:db8:0:b::2 |
port4.13 (VLAN 13) |
RT-3.6.2 | VRF-4 |
192.0.2.45/30 |
192.0.2.46 |
2001:db8:0:c::1/126 |
2001:db8:0:c::2 |
-
Policy:
CLUSTER_FACING_POLICY(type = VRF_SELECTION_POLICY) under network instanceDEFAULT, bound on subinterface0of active ingress interfaces viaapply-vrf-selection-policy. -
Traffic profile: 512-byte frames at 1,000 fps, fixed count of 32,000 packets per flow per measurement window (unless continuous mode is specified in RT-3.6.5). Always assert
Tx > 0andRx == Tx. -
Convergence gate (using
gnmi.Watch/gnmi.Await, 2-minute timeout, notime.Sleep):-
/interfaces/interface/state/oper-status == UPon all active interfaces and/lacp/interfaces/interface/members/member/state/synchronization == IN_SYNCon all aggregate members. -
/network-instances/network-instance/policy-forwarding/interfaces/interface/state/apply-vrf-selection-policy == CLUSTER_FACING_POLICYon all bound interfaces and absent on unbound interfaces. -
/network-instances/network-instance/policy-forwarding/policies/policy/rules/rule/state/sequence-idmatches the expected rule sequence IDs. -
/network-instances/network-instance/afts/ipv4-unicast/ipv4-entryandipv6-unicast/ipv6-entryresolve vianext-hop-groupto the expected ATE next-hop IP addresses inDEFAULTandVRF-1..VRF-4. - Subinterface IPv4/IPv6 neighbor
link-layer-addressis present on the DUT, andWaitForARP(IPv4andIPv6) succeeds on the ATE.
-
-
Linecard boot recovery gate (for each rebooted linecard
LC):- Watch
/components/component[name=LC]/state/oper-statusleaveACTIVEand return toACTIVE(timeout 15 minutes). - Verify
/components/component[name=LC]/state/last-reboot-timeincreased past its pre-reboot value andlast-reboot-reasonis populated. - Watch all physical and aggregate interfaces hosted on
LCreachoper-status == UPand LACP membersynchronization == IN_SYNC(timeout 5 minutes). - Run the full Convergence gate.
- Watch
-
Stability check (at the end of every subtest): verify
/system/processes/process/state/start-timeand/components/component/state/last-reboot-timehave not changed unexpectedly from baseline (updating the baseline for intentionally rebooted linecards/chassis).
-
Step 1 - Configure DUT:
- Configure
port1,port2,port3,port4.10(VRF-1,L3VRF), andport4.20(DEFAULT). - Program static routes in
VRF-1(198.51.100.0/24 -> 192.0.2.14,2001:db8:100::/48 -> 2001:db8:0:4::2) andDEFAULT(198.51.100.0/24&203.0.113.0/24 -> 192.0.2.18,2001:db8:100::/48&2001:db8:200::/48 -> 2001:db8:0:5::2). - Configure
CLUSTER_FACING_POLICYwith rule10(IPv4destination-address = 198.51.100.0/24 -> VRF-1) and rule20(IPv6destination-address = 2001:db8:100::/48 -> VRF-1), and bind toport1,port2, andport3.
- Configure
The representative JSON below illustrates the OpenConfig VRF selection policy and interface binding structure used across RT-3.6:
{
"interfaces": {
"interface": [
{
"config": {
"enabled": true,
"name": "port1",
"type": "iana-if-type:ethernetCsmacd"
},
"name": "port1",
"subinterfaces": {
"subinterface": [
{
"config": {
"index": 0
},
"index": 0
}
]
}
}
]
},
"network-instances": {
"network-instance": [
{
"config": {
"name": "VRF-1",
"type": "openconfig-network-instance-types:L3VRF"
},
"name": "VRF-1"
},
{
"config": {
"name": "DEFAULT",
"type": "openconfig-network-instance-types:DEFAULT_INSTANCE"
},
"name": "DEFAULT",
"policy-forwarding": {
"interfaces": {
"interface": [
{
"config": {
"apply-vrf-selection-policy": "CLUSTER_FACING_POLICY",
"interface-id": "port1"
},
"interface-id": "port1",
"interface-ref": {
"config": {
"interface": "port1",
"subinterface": 0
}
}
}
]
},
"policies": {
"policy": [
{
"config": {
"policy-id": "CLUSTER_FACING_POLICY",
"type": "openconfig-policy-forwarding:VRF_SELECTION_POLICY"
},
"policy-id": "CLUSTER_FACING_POLICY",
"rules": {
"rule": [
{
"action": {
"config": {
"network-instance": "VRF-1"
}
},
"config": {
"sequence-id": 10
},
"ipv4": {
"config": {
"destination-address": "198.51.100.0/24"
}
},
"sequence-id": 10
},
{
"action": {
"config": {
"network-instance": "VRF-1"
}
},
"config": {
"sequence-id": 20
},
"ipv6": {
"config": {
"destination-address": "2001:db8:100::/48"
}
},
"sequence-id": 20
}
]
}
}
]
}
}
}
]
}
}-
Step 2 - Convergence & Telemetry Stream:
- Run the Convergence gate.
- Subscribe (
SAMPLE, 10s interval) to/network-instances/network-instance/policy-forwarding/policies/policy/rules/rule/state/matched-pktsfor rules10and20.
-
Step 3 - Per-Linecard Traffic & Validation:
- For each ingress port
Nin{1, 2, 3}sequentially, send 4 flows (32,000 packets each):-
PN-IPV4-BASE(dst = 198.51.100.1->port4.10inVRF-1) -
PN-IPV6-BASE(dst = 2001:db8:100::1->port4.10inVRF-1) -
PN-IPV4-NOMATCH(dst = 203.0.113.1->port4.20inDEFAULT) -
PN-IPV6-NOMATCH(dst = 2001:db8:200::1->port4.20inDEFAULT)
-
- Verify
Rx == Txon all 4 flows,port4.10andport4.20out-pktsdeltas in[64000, 64640]per window ([192000, 193920]cumulative across 3 ports), rule10and rule20matched-pktsdeltas in[96000, 96960]cumulative, and non-empty 10s sample stream updates.
- For each ingress port
-
Step 1 - Scale DUT configuration in place:
- Configure
Agg-A(port5),Agg-B(port6),Agg-C(port7),port8(DEFAULT), andport4.11(VRF-2),port4.12(VRF-3),port4.13(VRF-4) per the Addressing table. - Move
DEFAULTstatic routes toport8(192.0.2.34/2001:db8:0:9::2) and deleteport4.20. - Expand
CLUSTER_FACING_POLICYto 34 rules (keeping rules10and20), foriin0..15:- IPv4 rule
100 + 10*i(100..250):destination-address = 198.18.i.0/24,action.network-instance = VRF-((i mod 4) + 1). - IPv6 rule
300 + 10*i(300..450):destination-address = 2001:db8:400:<i in hex>::/64,action.network-instance = VRF-((i mod 4) + 1).
- IPv4 rule
- Program static routes for all 32 scale prefixes in their respective
VRF-1..VRF-4and inDEFAULT(viaport8), and bindCLUSTER_FACING_POLICYto all 6 ingress interfaces (port1..3,Agg-A..C).
- Configure
-
Step 2 - Per-Linecard Traffic Validation (
K = 6active ingress interfaces):- Run the Convergence gate.
- For each ingress interface
Nin{1, 2, 3, 5, 6, 7}(36 flows, 32,000 packets each):-
PN-IPV4-BASE(198.51.100.1->port4.10) &PN-IPV6-BASE(2001:db8:100::1->port4.10) -
PN-IPV4-SCALE(16 destinations198.18.0.1..198.18.15.1->port4.10..13) &PN-IPV6-SCALE(16 destinations2001:db8:400::1..2001:db8:400:f::1->port4.10..13) -
PN-IPV4-NOMATCH(203.0.113.1->port8) &PN-IPV6-NOMATCH(2001:db8:200::1->port8)
-
- Verify
Rx == Txon all 36 flows, per-port and cumulative egress subinterfaceout-pktsdeltas (port4.10:[80000*K, 80800*K];port4.11..13:[16000*K, 16160*K]each;port8:[64000*K, 64640*K]), rule10&20matched-pktsdeltas in[32000*K, 32320*K], and each scale rule (100..250,300..450)matched-pktsdelta in[2000*K, 2020*K].
-
Step 1: Add static routes for
2001:db8:300::/48inVRF-1(-> 2001:db8:0:4::2) andDEFAULT(-> 2001:db8:0:9::2). Replace rule20ipv6/config/destination-addresswith2001:db8:300::/48and watch state update. -
Step 2: Run the Convergence gate and validate per-linecard traffic across all 6 ingress interfaces (
K = 6) usingPN-IPV6-MOD(dst = 2001:db8:300::1->port4.10). -
Step 3: Restore rule
20destination-addressto2001:db8:100::/48, remove the2001:db8:300::/48static routes, run the Convergence gate, and re-verify traffic (K = 6) withPN-IPV6-BASE.
- Repeat for each ingress port
Fin[port1, port5 (Agg-A), port2, port6 (Agg-B), port3, port7 (Agg-C)]:- Set
/interfaces/interface[name=F]/config/enabled = falseand watchF(and its aggregate interface ifFis a LAG member) reachoper-status == DOWN. - Verify
apply-vrf-selection-policystate remainsCLUSTER_FACING_POLICYon all 6 ingress interfaces and validate traffic across the 5 remaining up ingress interfaces (K = 5). - Set
/interfaces/interface[name=F]/config/enabled = true, watchF(and its aggregate + LACPIN_SYNC) return toUP, run the Convergence gate, and validate traffic across all 6 ingress interfaces (K = 6).
- Set
- For each distinct discovered ingress linecard
LCinLC_INGRESS(1 iteration per linecard, whereREMAININGis the subset of ingress ports{1, 2, 3, 5, 6, 7}not hosted onLC):- If
port4andport8are not onLCandREMAININGis non-empty, start the flows onREMAININGports in continuous mode and verify active transmission. - Record
last-reboot-timeforLCand issue gNOISystem.Reboot(method = COLD,subcomponents = [LC]). - Run the Linecard boot recovery gate for
LC, stop any active continuousREMAININGflows, and verifyTx > 0andRx == Tx(zero loss on un-rebooted linecards). - Reconfigure all 36 flows to fixed 32,000-packet mode, run the Convergence gate, and validate per-linecard traffic across all 6 ingress interfaces (
K = 6).
- If
- Pre-program static routes for
2001:db8:300::/48inVRF-1andDEFAULT. - For each distinct discovered ingress linecard
LCinLC_INGRESS(1 iteration per linecard, with a representative physical ingress portPand aggregateAgg(memberM) onLC, and remaining aggregatesOtherAgg1,OtherAgg2):- Set ATE port
Mlink stateDOWNand watchAggoper-status == DOWN. - Issue gNOI
System.Reboot(COLD) for subcomponentLC. - Watch
LCleaveACTIVE, then watch physical portPreachoper-status == UPwhileAggis stillDOWN. - Immediately execute three sequential gNMI
SetRequests:-
REPLACErule20destination-addresswith2001:db8:300::/48. -
DELETEapply-vrf-selection-policyonOtherAgg1andOtherAgg2. -
UPDATEapply-vrf-selection-policy = CLUSTER_FACING_POLICYonOtherAgg1andOtherAgg2.
-
- Set ATE port
Mlink stateUP, watchAggreachUP(verifying the 3SetRequests completed beforeAggcameUP, retrying up to 2 times if needed), and complete the Linecard boot recovery gate. - Validate per-linecard traffic (
K = 6) withPN-IPV6-MOD, then restore rule20to2001:db8:100::/48, run the Convergence gate, and validate withPN-IPV6-BASE.
- Set ATE port
- Remove
2001:db8:300::/48static routes.
-
Part A - Simultaneous reboot of
LC_INGRESS(1 iteration):- Issue a single gNOI
System.Reboot(COLD) withsubcomponents = LC_INGRESS, run the Linecard boot recovery gate for all rebooted linecards, and validate all 36 flows (K = 6).
- Issue a single gNOI
-
Part B - Full DUT reboot (1 iteration):
- Record
/system/state/boot-time, issue chassis-level gNOISystem.Reboot(COLD, emptysubcomponents), and watch/system/state/boot-timeincrease (timeout 30 minutes). - Watch all discovered linecards in
ALL_LCSreachoper-status == ACTIVE(timeout 20 minutes). - Verify
VRF-1..VRF-4,CLUSTER_FACING_POLICY(34 rules), and all 6 interface bindings persisted without re-pushing config, run the Convergence gate, validate all 36 flows (K = 6), and refresh the stability baseline.
- Record
-
Step 1 - In-place Replace: Push
gnmi.Replaceof the complete 34-ruleCLUSTER_FACING_POLICYand all 6 interface bindings without priorDelete, run the Convergence gate, and validate all 36 flows (K = 6). -
Step 2 - 5-Iteration Unbind/Rebind Churn: Repeat 5 cycles:
-
Unbind: Delete
apply-vrf-selection-policyon all 6 ingress interfaces, watch state clear, send all 36 flows, and verifyRx == Tx, all36 * 32,000 = 1,152,000packets egressport8(DEFAULT), andport4.10..13out-pktsdeltas are< 320(< 1%). -
Rebind: Re-apply
apply-vrf-selection-policy = CLUSTER_FACING_POLICYon all 6 ingress interfaces, run the Convergence gate, and validate all 36 flows (K = 6).
-
Unbind: Delete
-
Step 1: Discover all
INTEGRATED_CIRCUITcomponents parented (within 5 hops) to each discovered ingress linecard inLC_INGRESS. -
Step 2: Subscribe (
SAMPLE, 10s interval) to/components/component/integrated-circuit/utilization/resources/resource/state/{name,used,free,max-limit,high-watermark}for each discovered chip. -
Step 3: Unbind
CLUSTER_FACING_POLICYfrom all 6 ingress interfaces, watch bindings clear, and record 3 consecutive stable 10s samplesU_unbound(IC, R). -
Step 4: Rebind
CLUSTER_FACING_POLICYto all 6 ingress interfaces, run the Convergence gate, and record 3 consecutive stable 10s samplesU_bound(IC, R). -
Step 5: Verify
R_pbf = { R | U_bound(IC, R) > U_unbound(IC, R) }is non-empty on each discovered ingress linecard inLC_INGRESS; if the linecards inLC_INGRESSshare the same/components/component/state/part-noand host equal numbers of bound ingress interfaces, verify per-linecard totals are within 10% of the mean; verifyused + free == max-limit(whenmax-limit > 0),high-watermark >= used, sample intervals<= 15s, and validate all 36 flows (K = 6).
-
RT-3.6.10.1 - Atomic rejection of partially invalid
SetRequest: Push a single raw JSONSetRequestcontaining valid rule600(198.19.0.0/24 -> VRF-1) and invalid rule610(300.1.1.0/24 -> VRF-1). Verify theSetRequestis rejected, neither rule600nor610appears in state, and all 36 flows pass validation (K = 6). -
RT-3.6.10.2 - Binding to non-existent policy: Attempt to set
apply-vrf-selection-policy = NO_SUCH_POLICYonport1. Verify the other 5 ingress interfaces remain bound toCLUSTER_FACING_POLICY, restoreport1binding if needed, and validate all 36 flows (K = 6). -
RT-3.6.10.3 - Rule referencing non-existent target VRF: Attempt to add rule
700(198.19.1.0/24 -> VRF-GHOST). Verify rejection (or clean up if accepted), verify the 34 valid rules remain intact, and validate all 36 flows (K = 6). -
RT-3.6.10.4 - Missing route in target VRF drops traffic without fallback to
DEFAULT: Delete static route198.18.0.0/24inVRF-1while keeping198.18.0.0/24 -> 192.0.2.34inDEFAULT. Send 32,000 packets per ingress interface (dst = 198.18.0.1, matching rule100 -> VRF-1) and verifyRx == 0(100% dropped), rule100matched-pktsincreases by192,000, andport8out-pktsdoes not increase (< 320). Restore theVRF-1route and validate all 36 flows (K = 6). -
RT-3.6.10.5 - Deleting a VRF referenced by active policy rules: Attempt to delete
VRF-4while referenced by rules130..450. VerifyVRF-4remains intact (or restore if accepted) and validate all 36 flows (K = 6).
Registered via t.Cleanup so it runs even if a subtest fails:
- Stop ATE traffic and restore all ATE port link states and DUT interfaces
port1..port8toUP/enabled = true. - Delete policy-forwarding bindings and
CLUSTER_FACING_POLICY, test-added static routes inDEFAULT,VRF-1..VRF-4, andport4subinterfaces10..13,20. - Clear
aggregate-idonport5..port7and delete LACP and aggregate interfacesAgg-A..Agg-C.
paths:
# Interface and VLAN subinterface configuration
/interfaces/interface/config/enabled:
/interfaces/interface/config/type:
/interfaces/interface/subinterfaces/subinterface/vlan/match/single-tagged/config/vlan-id:
# Aggregate (LACP) interfaces
/interfaces/interface/aggregation/config/lag-type:
/interfaces/interface/ethernet/config/aggregate-id:
/lacp/interfaces/interface/config/name:
/lacp/interfaces/interface/config/interval:
/lacp/interfaces/interface/config/lacp-mode:
/lacp/interfaces/interface/members/member/state/synchronization:
# Interface state and counters
/interfaces/interface/state/admin-status:
/interfaces/interface/state/oper-status:
/interfaces/interface/state/hardware-port:
/interfaces/interface/state/counters/out-pkts:
/interfaces/interface/subinterfaces/subinterface/state/counters/out-pkts:
/interfaces/interface/subinterfaces/subinterface/ipv4/neighbors/neighbor/state/link-layer-address:
/interfaces/interface/subinterfaces/subinterface/ipv6/neighbors/neighbor/state/link-layer-address:
# Linecard and forwarding chip discovery, reboot recovery
/components/component/state/parent:
platform_type: ["PORT", "INTEGRATED_CIRCUIT"]
/components/component/state/type:
platform_type: ["LINECARD", "INTEGRATED_CIRCUIT"]
/components/component/state/oper-status:
platform_type: ["LINECARD"]
/components/component/state/last-reboot-time:
platform_type: ["LINECARD"]
/components/component/state/last-reboot-reason:
platform_type: ["LINECARD"]
/components/component/state/part-no:
platform_type: ["LINECARD"]
/system/state/boot-time:
# Hardware resource utilization
/components/component/integrated-circuit/utilization/resources/resource/state/name:
platform_type: ["INTEGRATED_CIRCUIT"]
/components/component/integrated-circuit/utilization/resources/resource/state/used:
platform_type: ["INTEGRATED_CIRCUIT"]
/components/component/integrated-circuit/utilization/resources/resource/state/free:
platform_type: ["INTEGRATED_CIRCUIT"]
/components/component/integrated-circuit/utilization/resources/resource/state/max-limit:
platform_type: ["INTEGRATED_CIRCUIT"]
/components/component/integrated-circuit/utilization/resources/resource/state/high-watermark:
platform_type: ["INTEGRATED_CIRCUIT"]
# DUT stability
/system/processes/process/state/name:
/system/processes/process/state/start-time:
# Network instances and static routes
/network-instances/network-instance/config/type:
/network-instances/network-instance/interfaces/interface/config/interface:
/network-instances/network-instance/interfaces/interface/config/subinterface:
/network-instances/network-instance/protocols/protocol/static-routes/static/config/prefix:
/network-instances/network-instance/protocols/protocol/static-routes/static/next-hops/next-hop/config/next-hop:
# Forwarding state (AFT) used to gate traffic
/network-instances/network-instance/afts/ipv4-unicast/ipv4-entry/state/prefix:
/network-instances/network-instance/afts/ipv4-unicast/ipv4-entry/state/next-hop-group:
/network-instances/network-instance/afts/ipv6-unicast/ipv6-entry/state/prefix:
/network-instances/network-instance/afts/ipv6-unicast/ipv6-entry/state/next-hop-group:
/network-instances/network-instance/afts/next-hop-groups/next-hop-group/state/id:
/network-instances/network-instance/afts/next-hops/next-hop/state/ip-address:
# VRF selection policy configuration
/network-instances/network-instance/policy-forwarding/policies/policy/config/policy-id:
/network-instances/network-instance/policy-forwarding/policies/policy/config/type:
/network-instances/network-instance/policy-forwarding/policies/policy/rules/rule/config/sequence-id:
/network-instances/network-instance/policy-forwarding/policies/policy/rules/rule/ipv4/config/destination-address:
/network-instances/network-instance/policy-forwarding/policies/policy/rules/rule/ipv6/config/destination-address:
/network-instances/network-instance/policy-forwarding/policies/policy/rules/rule/action/config/network-instance:
# VRF selection policy interface binding
/network-instances/network-instance/policy-forwarding/interfaces/interface/config/interface-id:
/network-instances/network-instance/policy-forwarding/interfaces/interface/config/apply-vrf-selection-policy:
/network-instances/network-instance/policy-forwarding/interfaces/interface/interface-ref/config/interface:
/network-instances/network-instance/policy-forwarding/interfaces/interface/interface-ref/config/subinterface:
# VRF selection policy state and counters
/network-instances/network-instance/policy-forwarding/policies/policy/state/type:
/network-instances/network-instance/policy-forwarding/policies/policy/rules/rule/state/sequence-id:
/network-instances/network-instance/policy-forwarding/policies/policy/rules/rule/ipv6/state/destination-address:
/network-instances/network-instance/policy-forwarding/interfaces/interface/state/apply-vrf-selection-policy:
/network-instances/network-instance/policy-forwarding/policies/policy/rules/rule/state/matched-pkts:
rpcs:
gnmi:
gNMI.Get:
gNMI.Set:
replace: true
update: true
delete: true
gNMI.Subscribe:
on_change: true
sample: true
gnoi:
system.System.Reboot:- MFF - A modular form factor device containing
LINECARD,FABRIC, and redundantCONTROLLER_CARDcomponents (at least 2 distinctLINECARDcomponents acrossport1..port8, using up to 3 distinct ingress linecards when available).