cfm_base - openconfig/featureprofiles GitHub Wiki
This test verifies CFM "DOWN MEP" can be established over "EthoCWoMPLSoGRE" dataplane.
DUT has an ingress and 2 egress aggregate interfaces.
[ ATE Port 1 ]----| Port1 :DUT1: Port2 | ---- |Port2 :DUT2: Port1 | ---- |ATE Port 2 |
Test uses aggregate 802.3ad bundled interfaces (Aggregate Interfaces).
-
Ingress Port: nTraffic is generated from Aggregate1 (ATE Ports 1).
-
Egress Ports: Aggregate2 (ATE Port 2) is used as the destination ports for encapsulated traffic.
-
Transit Ports: Aggregate3 (DUT1 port 2 and DUT2 Port 2)
Aggregate 1 and Aggregate2 i.e "customer interface's" are the customer facing ports that could either have port mode configuration or attachment mode configuration as described below.
EACH test should be run twice - once with port mode configuration and once with attachment in sub-interface mode configuration.
port mode configuration implies CFM configured on main Port as an attachment and vlan-mode is when cfm is confirued between attachments on ansub-interface.
Port mode will have Link loss forwarding enabled while sub-interface mode may not.
- Configure DUT1 port 1 to be a member of aggregate interface named "customer interface"
- "customer interface" is a static Layer 2 bundled interface part of pseudowire that accepts packets from all VLANs.
- MTU default 9216
- Configure DUT1 port 1 to be a member of aggregate interface named "customer interface"
- Create a sub interface of the aggregated interface and assign a VLAN ID to it.
- This sub interface will be a static Layer 2 bundled interface part of pseudowire that accepts packets from vlan ID associated with it.
- MTU default 9216
- Configure DUT2 port 1 to be a member of aggregate interface named "customer interface"
- "customer interface" is a static Layer 2 bundled interface part of pseudowire that accepts packets from all VLANs.
- MTU default 9216
- Configure DUT2 port 1 to be a member of aggregate interface named "customer interface"
- Create a sub interface of the aggregated interface and assign a VLAN ID to it.
- This sub interface will be a static Layer 2 bundled interface part of pseudowire that accepts packets from vlan ID associated with it.
- MTU default 9216
-
Policy-forwarding enabling EthoMPLSoGRE encapsulation of all incoming traffic:
-
The forwarding policy must allow forwarding of incoming traffic across 16 tunnels. 16 Tunnels has 16 source address and a single tunnel destination.
-
Source address must be configurable as:
- Loopback address OR
- 16 source addresses corresponding to a single tunnel destinations to achieve maximum entropy.
-
DSCP of the innermost IP packet header must be preserved during encapsulation
-
DSCP of the GRE/outermost IP header must be configurable (Default TOS 96) during encapsulation
-
TTL of the outer GRE must be configurable (Default TTL 64)
-
QoS Hardware queues for all traffic must be configurable (default QoS hardaware class selected is 3)
-
- "Customer interface" is Aggregate 1 and Aggregate 2 pointing towards Aggregare3
- Two unique static MPLS label for local label and remote label.
- Enable control word
-
IPV4 and IPV6 addresses
-
MTU (default 9216)
-
LACP Member link configuration
-
Lag id
-
LACP (default: period short)
-
Carrier-delay (default up:3000 down:150)
-
Statistics load interval (default:30 seconds)
- Create static route for tunnel destination pointing towards Aggregate 2.
- Static mapping of MPLS label for encapsulation must be configurable
- Entire Label block must be reallocated for static MPLS
- Labels from start/end/mid ranges must be usable and configured corresponding to EthoMPLSoGRE encapsulation
CFM is cnfigured as UP MEP. The control plane is between the customer attachments on either PF.
- Configure CFM session on DUT1 Port 1 and DUT2 Port 1 at line rate with a mix of both IPV4 and IPv6 traffic. Use 64, 128, 256, 512, 1024 MTU bytes frame size.
- Adjacent ATE Ports must have an Active L2.
Verify:
- CFM session is established with default timers and All ccm PDUs are EthoCWoMPLSoGRE-encapsulated.
- Verify deadtimer at 3.5 (100ms --> 350ms) times the configured keepalive.
- CCM PDUs are constant flows hence are not ECMP'd across all available tunnels.
Run the test separately for both port mode and attachment mode "customer interface" configuration.
- Use same configuration profile as CFM-1.1.2 (Default Timers).
Verify:
- CCM PDU Destination is Multicast.
- CFM OpCode as - Continuity check message (1).
- Increasing sequence number for consequent CCM packets.
- Verify interval field in CCM packet for following fields.
- Transmitted interval 100ms.
- Max Lifetime 350ms.
- Min lifetime 325ms.
- Use same configuration profile as CFM-1.1.2
- Configure Wrong MD level on on endpoint.
- Revert MD level and configure different CCM interval (i.e 100ms and (10ms or 1s))
Verify:
- “wrong MD level” alarm (when induced) on the endpoints.
- Verify “wrong interval” alarm (when induced) on the endpoints.
- Use configuration profile as descrbied in CFM-1.1.2
- turn off TX/Shutdown ATE port 1 (only on one endpoint).
Verify:
- CCM PDU is recieved on the remote endpoint with the RDI flag Set.
- A "Remote Defect Detected" alarm is raised at the remote end-point.
- Use same configuration profile as descrbied in CFM-1.1.2.
- turn off DUT 1 port 2 (only one endpoint).
Verify:
- Both DUT 1 and DUT 2 observe a CCM timeoute Event
- DUT 1 and DUT 2 emit a CCM PDU with the RDI flag Set.
- Use configuration profile as describedd in CFM-1.1.2 (Port mode only).
- turn off TX/Shutdown ATE port 1 (only on one endpoint).
- revert TX on ATE port 1 and turn off DUT 1 port 2 (only one endpoint).
Verify:
- CCM PDU is recieved on the remote endpoint with the RDI flag Set.
- A "Remote Defect Detected" alarm is raised at the remote end-point.
- Use configuration profile as describedd in CFM-1.1.2.
- re-write defulat Loss threshold (3) knob to 6, 10 , 20, 100 and 255.
- Shutdown DUT 1 port 2 (only one endpoint).
- Use configuration profile as described in CFM-1.1.2.
- Configure 2 way DM measurement profiles on CFM session with 60 second measurement intervals.
Verify:
- DUT 1 and DUT 2 observe a min, max and mean Delay measurements at defined.
- Use configuration profile as described in CFM-1.1.2.
Verify:
- Both DUT 1 and DUT 2 observe a min, max and mean frame loss ratio for "far-end" & "near-end" with 60 second measurement intervals.
- Use configuration profile as describedd in CFM-1.1.2.
- Configure 1000 attachments, pseudowires and Establish 1000 CFM sessions between operating at 100ms keepalive:
Verify:
- Device Health and soak for at least 6 hrs.
{
"interfaces": {
"interface": [
{
"config": {
"description": "GEO_1",
"enabled": true,
"mtu": 9080,
"name": "Bundle-Ether43",
"type": "ieee8023adLag"
},
"name": "Bundle-Ether43",
"subinterfaces": {
"subinterface": [
{
"config": {
"description": "GEO_1",
"enabled": true,
"index": 1600
},
"index": 1600,
"vlan": {
"match": {
"single-tagged": {
"config": {
"vlan-id": 1600
}
}
}
}
}
]
}
},
{
"config": {
"description": "GEO_2",
"enabled": true,
"mtu": 9080,
"name": "Bundle-Ether5",
"type": "ieee8023adLag"
},
"name": "Bundle-Ether5",
"subinterfaces": {
"subinterface": [
{
"config": {
"description": "GEO_2",
"enabled": true,
"index": 4010
},
"index": 4010,
"vlan": {
"match": {
"single-tagged": {
"config": {
"vlan-id": 4010
}
}
}
}
}
]
}
},
{
"config": {
"description": "GEO_3",
"enabled": true,
"mtu": 9080,
"name": "Bundle-Ether5",
"type": "ieee8023adLag"
},
"name": "Bundle-Ether5",
"subinterfaces": {
"subinterface": [
{
"config": {
"description": "GEO_3",
"enabled": true,
"index": 4050
},
"index": 4050,
"vlan": {
"match": {
"single-tagged": {
"config": {
"vlan-id": 4050
}
}
}
}
}
]
}
},
{
"config": {
"description": "GEO_4",
"enabled": true,
"mtu": 9080,
"name": "Bundle-Ether43",
"type": "ieee8023adLag"
},
"name": "Bundle-Ether43",
"subinterfaces": {
"subinterface": [
{
"config": {
"description": "GEO_4",
"enabled": true,
"index": 1100
},
"index": 1100,
"vlan": {
"match": {
"single-tagged": {
"config": {
"vlan-id": 1100
}
}
}
}
}
]
}
}
]
}
}{
"oam": {
"cfm": {
"domains": {
"maintenance-domain": [
{
"config": {
"char-string": "D1",
"level": 5,
"md-id": "1",
"md-name-type": "CHARACTER_STRING"
},
"maintenance-associations": {
"maintenance-association": [
{
"config": {
"ccm-interval": "300MS",
"group-name": "GEO_1",
"loss-threshold": 3,
"ma-id": "S1",
"ma-name-type": "UINT16",
"unsigned-int16": 1
},
"ma-id": "S1",
"mep-endpoints": {
"mep-endpoint": [
{
"config": {
"ccm-enabled": true,
"direction": "UP",
"interface": "Bundle-Ether43.1600",
"local-mep-id": 40
},
"local-mep-id": 40,
"pm-profiles": {
"pm-profile": [
{
"config": {
"profile-name": "cfm_delay_Bundle-Ether43_1600"
},
"profile-name": "cfm_delay_Bundle-Ether43_1600"
},
{
"config": {
"profile-name": "cfm_loss_Bundle-Ether43_1600"
},
"profile-name": "cfm_loss_Bundle-Ether43_1600"
}
]
},
"rdi": {
"config": {
"transmit-on-defect": true
}
},
"remote-meps": {
"remote-mep": [
{
"config": {
"id": 39
},
"id": 39
}
]
}
}
]
}
}
]
},
"md-id": "1"
},
{
"config": {
"char-string": "D2",
"level": 5,
"md-id": "2",
"md-name-type": "CHARACTER_STRING"
},
"maintenance-associations": {
"maintenance-association": [
{
"config": {
"ccm-interval": "300MS",
"group-name": "GEO_2",
"loss-threshold": 3,
"ma-id": "S1",
"ma-name-type": "UINT16",
"unsigned-int16": 1
},
"ma-id": "S1",
"mep-endpoints": {
"mep-endpoint": [
{
"config": {
"ccm-enabled": true,
"direction": "UP",
"interface": "Bundle-Ether5.4010",
"local-mep-id": 6
},
"local-mep-id": 6,
"pm-profiles": {
"pm-profile": [
{
"config": {
"profile-name": "cfm_delay_Bundle-Ether5_4010"
},
"profile-name": "cfm_delay_Bundle-Ether5_4010"
},
{
"config": {
"profile-name": "cfm_loss_Bundle-Ether5_4010"
},
"profile-name": "cfm_loss_Bundle-Ether5_4010"
}
]
},
"rdi": {
"config": {
"transmit-on-defect": true
}
},
"remote-meps": {
"remote-mep": [
{
"config": {
"id": 5
},
"id": 5
}
]
}
}
]
}
}
]
},
"md-id": "2"
},
{
"config": {
"char-string": "D3",
"level": 5,
"md-id": "3",
"md-name-type": "CHARACTER_STRING"
},
"maintenance-associations": {
"maintenance-association": [
{
"config": {
"ccm-interval": "300MS",
"group-name": "GEO_3",
"loss-threshold": 3,
"ma-id": "S1",
"ma-name-type": "UINT16",
"unsigned-int16": 1
},
"ma-id": "S1",
"mep-endpoints": {
"mep-endpoint": [
{
"config": {
"ccm-enabled": true,
"direction": "UP",
"interface": "Bundle-Ether5.4050",
"local-mep-id": 8
},
"local-mep-id": 8,
"pm-profiles": {
"pm-profile": [
{
"config": {
"profile-name": "cfm_delay_Bundle-Ether5_4050"
},
"profile-name": "cfm_delay_Bundle-Ether5_4050"
},
{
"config": {
"profile-name": "cfm_loss_Bundle-Ether5_4050"
},
"profile-name": "cfm_loss_Bundle-Ether5_4050"
}
]
},
"rdi": {
"config": {
"transmit-on-defect": true
}
},
"remote-meps": {
"remote-mep": [
{
"config": {
"id": 7
},
"id": 7
}
]
}
}
]
}
}
]
},
"md-id": "3"
},
{
"config": {
"char-string": "D4",
"level": 5,
"md-id": "4",
"md-name-type": "CHARACTER_STRING"
},
"maintenance-associations": {
"maintenance-association": [
{
"config": {
"ccm-interval": "300MS",
"group-name": "GEO_4",
"loss-threshold": 3,
"ma-id": "S1",
"ma-name-type": "UINT16",
"unsigned-int16": 1
},
"ma-id": "S1",
"mep-endpoints": {
"mep-endpoint": [
{
"config": {
"ccm-enabled": true,
"direction": "UP",
"interface": "Bundle-Ether43.1100",
"local-mep-id": 36
},
"local-mep-id": 36,
"pm-profiles": {
"pm-profile": [
{
"config": {
"profile-name": "cfm_delay_Bundle-Ether43_1100"
},
"profile-name": "cfm_delay_Bundle-Ether43_1100"
},
{
"config": {
"profile-name": "cfm_loss_Bundle-Ether43_1100"
},
"profile-name": "cfm_loss_Bundle-Ether43_1100"
}
]
},
"rdi": {
"config": {
"transmit-on-defect": true
}
},
"remote-meps": {
"remote-mep": [
{
"config": {
"id": 35
},
"id": 35
}
]
}
}
]
}
}
]
},
"md-id": "4"
}
]
},
"performance-measurement-profiles-global": {
"performance-measurement-profile": [
{
"config": {
"burst-interval": 10000,
"intervals-archived": 5,
"measurement-interval": 1,
"measurement-type": "DMM",
"packet-per-burst": 100,
"packets-per-meaurement-period": 60,
"profile-name": "cfm_delay_Bundle-Ether43_1100",
"repetition-period": 1
},
"profile-name": "cfm_delay_Bundle-Ether43_1100"
},
{
"config": {
"burst-interval": 10000,
"intervals-archived": 5,
"measurement-interval": 1,
"measurement-type": "DMM",
"packet-per-burst": 100,
"packets-per-meaurement-period": 60,
"profile-name": "cfm_delay_Bundle-Ether43_1600",
"repetition-period": 1
},
"profile-name": "cfm_delay_Bundle-Ether43_1600"
},
{
"config": {
"burst-interval": 10000,
"intervals-archived": 5,
"measurement-interval": 1,
"measurement-type": "DMM",
"packet-per-burst": 100,
"packets-per-meaurement-period": 60,
"profile-name": "cfm_delay_Bundle-Ether5_4010",
"repetition-period": 1
},
"profile-name": "cfm_delay_Bundle-Ether5_4010"
},
{
"config": {
"burst-interval": 10000,
"intervals-archived": 5,
"measurement-interval": 1,
"measurement-type": "DMM",
"packet-per-burst": 100,
"packets-per-meaurement-period": 60,
"profile-name": "cfm_delay_Bundle-Ether5_4050",
"repetition-period": 1
},
"profile-name": "cfm_delay_Bundle-Ether5_4050"
},
{
"config": {
"burst-interval": 10000,
"intervals-archived": 5,
"measurement-interval": 1,
"measurement-type": "SLM",
"packet-per-burst": 100,
"packets-per-meaurement-period": 60,
"profile-name": "cfm_loss_Bundle-Ether43_1100",
"repetition-period": 1
},
"profile-name": "cfm_loss_Bundle-Ether43_1100"
},
{
"config": {
"burst-interval": 10000,
"intervals-archived": 5,
"measurement-interval": 1,
"measurement-type": "SLM",
"packet-per-burst": 100,
"packets-per-meaurement-period": 60,
"profile-name": "cfm_loss_Bundle-Ether43_1600",
"repetition-period": 1
},
"profile-name": "cfm_loss_Bundle-Ether43_1600"
},
{
"config": {
"burst-interval": 10000,
"intervals-archived": 5,
"measurement-interval": 1,
"measurement-type": "SLM",
"packet-per-burst": 100,
"packets-per-meaurement-period": 60,
"profile-name": "cfm_loss_Bundle-Ether5_4010",
"repetition-period": 1
},
"profile-name": "cfm_loss_Bundle-Ether5_4010"
},
{
"config": {
"burst-interval": 10000,
"intervals-archived": 5,
"measurement-interval": 1,
"measurement-type": "SLM",
"packet-per-burst": 100,
"packets-per-meaurement-period": 60,
"profile-name": "cfm_loss_Bundle-Ether5_4050",
"repetition-period": 1
},
"profile-name": "cfm_loss_Bundle-Ether5_4050"
}
]
}
}
}
}paths:
# interface configs
/interfaces/interface/config/description:
/interfaces/interface/config/enabled:
/interfaces/interface/config/mtu:
/interfaces/interface/config/name:
/interfaces/interface/config/type:
/interfaces/interface/rates/config/load-interval:
/interfaces/interface/subinterfaces/subinterface/config/description:
/interfaces/interface/subinterfaces/subinterface/config/enabled:
/interfaces/interface/subinterfaces/subinterface/config/index:
/interfaces/interface/subinterfaces/subinterface/ipv4/config/mtu:
/interfaces/interface/subinterfaces/subinterface/ipv6/config/mtu:
/interfaces/interface/aggregation/config/lag-type:
#psuedowire configs
/network-instances/network-instance/config/name:
/network-instances/network-instance/config/type:
/network-instances/network-instance/connection-points/connection-point/config/connection-point-id:
/network-instances/network-instance/connection-points/connection-point/endpoints/endpoint/config/endpoint-id:
/network-instances/network-instance/connection-points/connection-point/endpoints/endpoint/local/config/interface:
/network-instances/network-instance/connection-points/connection-point/endpoints/endpoint/local/config/subinterface:
/network-instances/network-instance/connection-points/connection-point/endpoints/endpoint/remote/config/virtual-circuit-identifier:
#TODO: Add new OCs for labels and next-hop-group under connection-point
#/network-instances/network-instance/connection-points/connection-point/endpoints/endpoint/local/config/local-label
#/network-instances/network-instance/connection-points/connection-point/endpoints/endpoint/local/config/remote-label
#/network-instances/network-instance/connection-points/connection-point/endpoints/endpoint/remote/config/next-hop-group
#Tunnels/Next-hop group configs
#TODO: Revisit and update as per https://github.com/openconfig/public/pull/1308
#network-instances/network-instance/static/next-hop-groups/next-hop-group/nexthops/nexthop/config/index:
#/network-instances/network-instance/static/next-hop-groups/next-hop-group/nexthops/nexthop/config/next-hop:
#/network-instances/network-instance/static/next-hop-groups/next-hop-group/nexthops/nexthop/encap-headers/encap-header/config/index:
#/network-instances/network-instance/static/next-hop-groups/next-hop-group/nexthops/nexthop/encap-headers/encap-header/gre/config/type:
#/network-instances/network-instance/static/next-hop-groups/next-hop-group/nexthops/nexthop/encap-headers/encap-header/gre/config/dst-ip:
#/network-instances/network-instance/static/next-hop-groups/next-hop-group/nexthops/nexthop/encap-headers/encap-header/gre/config/src-ip:
#/network-instances/network-instance/static/next-hop-groups/next-hop-group/nexthops/nexthop/encap-headers/encap-header/gre/config/dscp:
#/network-instances/network-instance/static/next-hop-groups/next-hop-group/nexthops/nexthop/encap-headers/encap-header/gre/config/ip-ttl:
#/network-instances/network-instance/static/next-hop-groups/next-hop-group/nexthops/nexthop/encap-headers/encap-header/gre/config/index:
# Telemetry paths
/oam/cfm/domains/maintenance-domain/state/md-id:
/oam/cfm/domains/maintenance-domain/maintenance-associations/maintenance-association/state/ma-id:
/oam/cfm/domains/maintenance-domain/maintenance-associations/maintenance-association/mep-endpoints/mep-endpoint/state/local-mep-id:
/oam/cfm/domains/maintenance-domain/maintenance-associations/maintenance-association/mep-endpoints/mep-endpoint/remote-meps/remote-mep/state/id:
/oam/cfm/performance-measurement-profiles-global/performance-measurement-profile/state/profile-name:
/oam/cfm/domains/maintenance-domain/maintenance-associations/maintenance-association/mep-endpoints/mep-endpoint/pm-profiles/pm-profile/state/delay-measurement-state/frame-delay-two-way-average:
/oam/cfm/domains/maintenance-domain/maintenance-associations/maintenance-association/mep-endpoints/mep-endpoint/pm-profiles/pm-profile/state/delay-measurement-state/frame-delay-two-way-max:
/oam/cfm/domains/maintenance-domain/maintenance-associations/maintenance-association/mep-endpoints/mep-endpoint/pm-profiles/pm-profile/state/delay-measurement-state/frame-delay-two-way-min:
/oam/cfm/domains/maintenance-domain/maintenance-associations/maintenance-association/mep-endpoints/mep-endpoint/pm-profiles/pm-profile/state/measurement-type:
/oam/cfm/domains/maintenance-domain/maintenance-associations/maintenance-association/mep-endpoints/mep-endpoint/pm-profiles/pm-profile/state/loss-measurement-state/far-end-average-frame-loss-ratio:
/oam/cfm/domains/maintenance-domain/maintenance-associations/maintenance-association/mep-endpoints/mep-endpoint/pm-profiles/pm-profile/state/loss-measurement-state/far-end-max-frame-loss-ratio:
/oam/cfm/domains/maintenance-domain/maintenance-associations/maintenance-association/mep-endpoints/mep-endpoint/pm-profiles/pm-profile/state/loss-measurement-state/far-end-min-frame-loss-ratio:
/oam/cfm/domains/maintenance-domain/maintenance-associations/maintenance-association/mep-endpoints/mep-endpoint/pm-profiles/pm-profile/state/loss-measurement-state/near-end-average-frame-loss-ratio:
/oam/cfm/domains/maintenance-domain/maintenance-associations/maintenance-association/mep-endpoints/mep-endpoint/pm-profiles/pm-profile/state/loss-measurement-state/near-end-max-frame-loss-ratio:
/oam/cfm/domains/maintenance-domain/maintenance-associations/maintenance-association/mep-endpoints/mep-endpoint/pm-profiles/pm-profile/state/loss-measurement-state/near-end-min-frame-loss-ratio:
# Config paths for GRE decap
/network-instances/network-instance/policy-forwarding/policies/policy/rules/rule/action/config/decapsulate-gre:
# Config Paths for CFM
#/oam/cfm/domains/domain/config/name:
/oam/cfm/domains/maintenance-domain/config/level:
/oam/cfm/domains/maintenance-domain/config/md-id:
/oam/cfm/domains/maintenance-domain/config/md-name-type:
/oam/cfm/domains/maintenance-domain/maintenance-associations/maintenance-association/config/ccm-interval:
/oam/cfm/domains/maintenance-domain/maintenance-associations/maintenance-association/config/loss-threshold:
/oam/cfm/domains/maintenance-domain/maintenance-associations/maintenance-association/config/ma-id:
/oam/cfm/domains/maintenance-domain/maintenance-associations/maintenance-association/config/ma-name-type:
/oam/cfm/domains/maintenance-domain/maintenance-associations/maintenance-association/mep-endpoints/mep-endpoint/config/ccm-enabled:
/oam/cfm/domains/maintenance-domain/maintenance-associations/maintenance-association/mep-endpoints/mep-endpoint/config/direction:
/oam/cfm/domains/maintenance-domain/maintenance-associations/maintenance-association/mep-endpoints/mep-endpoint/config/interface:
/oam/cfm/domains/maintenance-domain/maintenance-associations/maintenance-association/mep-endpoints/mep-endpoint/config/local-mep-id:
/oam/cfm/domains/maintenance-domain/maintenance-associations/maintenance-association/mep-endpoints/mep-endpoint/pm-profiles/pm-profile/config/profile-name:
/oam/cfm/domains/maintenance-domain/maintenance-associations/maintenance-association/mep-endpoints/mep-endpoint/rdi/config/transmit-on-defect:
/oam/cfm/domains/maintenance-domain/maintenance-associations/maintenance-association/mep-endpoints/mep-endpoint/remote-meps/remote-mep/config/id:
/oam/cfm/performance-measurement-profiles-global/performance-measurement-profile/config/burst-interval:
/oam/cfm/performance-measurement-profiles-global/performance-measurement-profile/config/intervals-archived:
/oam/cfm/performance-measurement-profiles-global/performance-measurement-profile/config/measurement-interval:
/oam/cfm/performance-measurement-profiles-global/performance-measurement-profile/config/measurement-type:
/oam/cfm/performance-measurement-profiles-global/performance-measurement-profile/config/packet-per-burst:
/oam/cfm/performance-measurement-profiles-global/performance-measurement-profile/config/packets-per-meaurement-period:
/oam/cfm/performance-measurement-profiles-global/performance-measurement-profile/config/profile-name:
/oam/cfm/performance-measurement-profiles-global/performance-measurement-profile/config/repetition-period:
rpcs:
gnmi:
gNMI.Set:
union_replace: true
replace: true
gNMI.Subscribe:
on_change: true
- MFF
- FFF