aggregate_test - openconfig/featureprofiles GitHub Wiki

RT-5.2: Aggregate Interfaces

Canonical OC

{}

Summary

Validate link operational status of Static LAG and LACP.

Procedure

  • Connect ATE port-1 to DUT port-1, and ATE ports 2 through 8 to DUT ports 2-8. Configure ATE and DUT ports 2-8 to be part of a LAG.
  • For both static LAG and LACP:
    • Ensure that LAG is successfully negotiated, verifying port status for each of DUT ports 2-8 reflects expected LAG state via ATE and DUT telemetry.
    • Ensure that configuring a minimum links setting for the LAG the entire interface is marked:
      • Down when min-1 links are up
      • Up when min links are up
      • Up when >min links are up.
    • TODO: Verify the above by sending flows between ATE port-1 targeted towards the LAG.

Config Parameter Coverage

  • /interfaces/interface/ethernet/config/port-speed
  • /interfaces/interface/ethernet/config/duplex-mode
  • /interfaces/interface/ethernet/config/aggregate-id
  • /interfaces/interface/aggregation/config/lag-type
  • /interfaces/interface/aggregation/config/min-links
  • TODO: /lacp/config/system-priority
  • /lacp/interfaces/interface/config/name
  • /lacp/interfaces/interface/config/interval
  • /lacp/interfaces/interface/config/lacp-mode
  • TODO: /lacp/interfaces/interface/config/system-id-mac
  • TODO: /lacp/interfaces/interface/config/system-priority

Telemetry Parameter Coverage

  • TODO: /lacp/interfaces/interface/members/member/state/counters/lacp-in-pkts
  • TODO: /lacp/interfaces/interface/members/member/state/counters/lacp-out-pkts
  • TODO: /lacp/interfaces/interface/members/member/state/counters/lacp-rx-errors
  • /lacp/interfaces/interface/name
  • /lacp/interfaces/interface/state/name
  • /lacp/interfaces/interface/members/member/interface
  • /lacp/interfaces/interface/members/member/state/interface
  • /lacp/interfaces/interface/members/member/state/oper-key
  • /lacp/interfaces/interface/members/member/state/partner-key
  • /lacp/interfaces/interface/members/member/state/partner-id
  • /lacp/interfaces/interface/members/member/state/system-id
  • /lacp/interfaces/interface/members/member/state/port-num
  • /interfaces/interface/ethernet/state/aggregate-id

OpenConfig Path and RPC Coverage

The below yaml defines the OC paths intended to be covered by this test.

paths:
  /interfaces/interface/aggregation/config/lag-type:
  /interfaces/interface/aggregation/config/min-links:
  /interfaces/interface/config/description:
  /interfaces/interface/config/enabled:
  /interfaces/interface/config/name:
  /interfaces/interface/config/type:
  /interfaces/interface/ethernet/config/aggregate-id:
  /interfaces/interface/ethernet/state/aggregate-id:
  /interfaces/interface/state/admin-status:
  /interfaces/interface/state/oper-status:
  /interfaces/interface/state/type:
  /interfaces/interface/subinterfaces/subinterface/ipv4/addresses/address/config/prefix-length:
  /interfaces/interface/subinterfaces/subinterface/ipv4/config/enabled:
  /interfaces/interface/subinterfaces/subinterface/ipv6/addresses/address/config/prefix-length:
  /interfaces/interface/subinterfaces/subinterface/ipv6/config/enabled:
  /lacp/interfaces/interface/config/interval:
  /lacp/interfaces/interface/config/lacp-mode:
  /lacp/interfaces/interface/members/member/state/collecting:
  /lacp/interfaces/interface/members/member/state/distributing:
  /lacp/interfaces/interface/members/member/state/interface:
  /lacp/interfaces/interface/members/member/state/oper-key:
  /lacp/interfaces/interface/members/member/state/partner-id:
  /lacp/interfaces/interface/members/member/state/partner-key:
  /lacp/interfaces/interface/members/member/state/partner-port-num:
  /lacp/interfaces/interface/members/member/state/port-num:
  /lacp/interfaces/interface/members/member/state/system-id:
  /lacp/interfaces/interface/state/name:
rpcs:
  gnmi:
    gNMI.Set:
    gNMI.Subscribe:
⚠️ **GitHub.com Fallback** ⚠️