This document reflects conflicts between

• NodeMCU/ESP8266,
• NodeMCU/ESP32,
• NodeMCU/Linux

and requirements to achieve larger degree of compatibility.

• adc: configure ADC (Analog/Digital Converter), read
• file: file operations, read/write
• gpio: configure GPIO, read/write
• i2c: configure I2C, read/write
• spi: configure SPI, read/write
• tmr: timer operations millisecond exact
• net: client and server (tcp/udp) networking
• node: general device information, cpu freq settings etc, read/write
• uart: configure UART, read/write
• wifi: configure WIFI (station/access-point)

Function	ESP8266	ESP32	Linux
init ADC	adc.force_init_mode(node)	adc.setup(adc_number,channel,atten)
read ADC	adc.read()	adc.read()
read system ADC	adc.readvdd33()

ESP8266:

• adc.force_init_mode(node) Checks and if necessary reconfigures the ADC mode setting in the ESP init data block.
  • mode:
    • adc.INIT_ADC
    • adc.INIT_VDD33
• adc.read() Samples the ADC.
• adc.readvdd33() Reads the system voltage.

ESP32:

• adc.setup(adc_number,channel,atten)
  • adc_number Only adc.ADC1 now
  • channel When using adc.ADC1: 0 to 7. 0: GPIO36, 1: GPIO37, 2: GPIO38, 3: GPIO39, 4: GPIO32, 5: GPIO33, 6: GPIO34, 7: GPIO35
  • atten One of following constants
    • adc.ATTEN_0db The input voltage of ADC will be reduced to about 1/1 (1.1V when VDD_A=3.3V)
    • adc.ATTEN_2_5db The input voltage of ADC will be reduced to about 1/1.34 (1.5V when VDD_A=3.3V)
    • adc.ATTEN_6db The input voltage of ADC will be reduced to about 1/2 (2.2V when VDD_A=3.3V)
    • adc.ATTEN_11db The input voltage of ADC will be reduced to about 1/3.6 (3.9V when VDD_A=3.3V, maximum voltage is limited by VDD_A)
• adc.read() Samples the ADC.

The object mode of file operations isn't implemented yet (file.read() vs src = file.open() src:read()) according dev-esp32 documentation.

Function	ESP8266	ESP32	Linux
open file	file.open()	file.open()	file.open()
close file	file.close()	file.close()	file.close()
read file	file.read()	file.read()	file.read()
write file	file.write()	file.write()	file.write()
seek file	file.seek()	file.seek()	file.seek()
flush file	file.flush()	file.flush()	file.flush()
stat file	file.stat()	file.stat()	file.stat()
list files	file.list()	file.list()	file.list()
close file (object-based)	file:close()		file:close()
read file (object-based)	file:read()		file:read()
write file (object-based)	file:write()		file:write()
read line (object-based)	file:readline()		file:readline()
write line (object-based)	file:writeline()		file:writeline()
seek file (object-based)	file:seek()		file:seek()
flush file (object-based)	file:flush()		file:flush()

ESP8266:

• file.obj:close() Closes the open file, if any.
• file.obj:flush() Flushes any pending writes to the file system, ensuring no data is lost on a restart.
• file.obj:read() Read content from the open file.
• file.obj:readline() Read the next line from the open file.
• file.obj:seek() Sets and gets the file position, measured from the beginning of the file, to the position given by offset plus a base specified by the string whence.
• file.obj:write() Write a string to the open file.
• file.obj:writeline() Write a string to the open file and append '\n' at the end.

ESP32:

• all above listed are missing according documentation

Function	ESP8266	ESP32	Linux
set single pin mode	gpio.mode(pin,type,pullup)		gpio.mode(pin,type,pullup)
set multiple pin mode		gpio.config({gpio=..,dir=..,pull=..,opendrain=..})
trigger callback	gpio.trig(pin,type,callback(level,when))	gpio.trig(pin,types,callback(pin,level))

ESP8266:

• gpio.mode(pin,type,pullup)
  • type:
    • gpio.INPUT
    • gpio.OUTPUT
    • gpio.OPENDRAIN
    • gpio.INT
  • pullup:
    • gpio.FLOAT (default)
    • gpio.PULLUP enables the weak pull-up resistor
• gpio.trig(pin,type,callback(level,when))
  • type: "up", "down", "both", "low", "high"

ESP32:

• gpio.config({gpio=..,dir=..,pull=..,opendrain=..})

  • dir:
    • gpio.IN
    • gpio.OUT
    • gpio.IN_OUT
  • pull:
    • gpio.FLOATING disables both pull-up and -down
    • gpio.PULL_UP enables pull-up and disables pull-down
    • gpio.PULL_DOWN enables pull-down and disables pull-up
    • gpio.PULL_UP_DOWN enables both pull-up and -down

• gpio.trig(pin,types,callback(pin,level))

  • type:
    • gpio.INTR_UP for trigger on rising edge
    • gpio.INTR_DOWN for trigger on falling edge
    • gpio.INTR_UP_DOWN for trigger on both edges
    • gpio.INTR_LOW for trigger on low level
    • gpio.INTR_HIGH for trigger on high level

Function	ESP8266	ESP32	Linux
general info	node.info()		node.info()
chip id	node.chipid()	node.chipid()	node.chipid()

ESP8266:

• node.info() returns 8 elements:

  • majorVer (number)
  • minorVer (number)
  • devVer (number)
  • chipid (number)
  • flashid (number)
  • flashsize (number)
  • flashmode (number)
  • flashspeed (number)

• node.chipid() returns an integer (last 3 bytes of the station MAC address)

ESP32:

• node.info() missing
• node.chipid() returns hex string with '0x' as prefix and 7 bytes whereas the last byte of the MAC address is dropped (risk of 256 identical chipids)

Linux:

• node.info() reports 8 elements plus new 9th element the architecture 'linux' ('esp8266' or 'esp32' as other options)
• node.chipid() reports last 3 octets of first network MAC address

Function	ESP8266	ESP32	Linux
microsecond counter [integer]	tmr.now()		tmr.now()
second counter [integer]	tmr.time()		tmr.time()
seconds with us precision [float]			tmr.uptime()

ESP8266:

• tmr.now() returns microseconds [integer]
• tmr.time() time in seconds since boot (uptime) [integer]
• tmr.uptime() might not be available when integer only firmware

ESP32:

• tmr.now() missing
• tmr.time() missing
• tmr.uptime() missing

Linux:

• tmr.uptime() added, uptime with microsecond precision [float]

Function	ESP8266	ESP32	Linux
change pins	uart.alt()
set callbacks	uart.on()1)	uart.on()2)
setup	uart.setup()	uart.setup()
get config	uart.getconfig()
write uart	uart.write()	uart.write()
start uart		uart.start()
stop uart		uart.stop()

1. and 2) API has changed, not compatible.

ESP8266:

• uart.alt(on) Change UART pin assignment (on: 0 = default, 1 = use alternate pins GPIO13 and GPIO15)
• uart.on(method, [number/end_char], [function], [run_input]) Sets the callback function to handle UART events.
• uart.setup() (Re-)configures the communication parameters of the UART.
• uart.getconfig() Returns the current configuration parameters of the UART.
• uart.write() Write string or byte to the UART.

ESP32:

• uart.on([id], method, [number/end_char], [function], [run_input]) Sets the callback function to handle UART events.
• uart.setup() (Re-)configures the communication parameters of the UART.
• uart.start() Start the UART.
• uart.stop() Stop the UART.
• uart.write() Write string or byte to the UART.

ESP8266 and ESP32 differ a lot:

ESP8266

• events are captured via wifi.eventmon.*:
  • wifi.eventmon.register(event[, function(T)])
    • wifi.eventmon.STA_CONNECTED
    • wifi.eventmon.STA_DISCONNECTED
    • wifi.eventmon.STA_AUTHMODE_CHANGE
    • wifi.eventmon.STA_GOT_IP
    • wifi.eventmon.STA_DHCP_TIMEOUT
    • wifi.eventmon.AP_STACONNECTED
    • wifi.eventmon.AP_STADISCONNECTED
    • wifi.eventmon.AP_PROBEREQRECVED

ESP32:

• events are captured via wifi.on()
  • wifi.ap.on(event, callback)
    • event:
      • start: no additional info
      • stop: no additional info
      • sta_connected: information about the client that connected:
      • mac: the MAC address
      • id: assigned station id (AID)
      • disconnected: information about disconnecting client
      • mac: the MAC address
      • probe_req: information about the probing client
      • from: MAC address of the probing client
      • rssi: Received Signal Strength Indicator value