• RFMXSPECAN_ATTR_NF_MEASUREMENT_ENABLED
• RFMXSPECAN_ATTR_NF_DUT_TYPE
• Frequency Converter
  • RFMXSPECAN_ATTR_NF_FREQUENCY_CONVERTER_LO_FREQUENCY
  • RFMXSPECAN_ATTR_NF_FREQUENCY_CONVERTER_FREQUENCY_CONTEXT
  • RFMXSPECAN_ATTR_NF_FREQUENCY_CONVERTER_SIDEBAND
  • RFMXSPECAN_ATTR_NF_FREQUENCY_CONVERTER_IMAGE_REJECTION
• RFMXSPECAN_ATTR_NF_FREQUENCY_LIST
• RFMXSPECAN_ATTR_NF_MEASUREMENT_BANDWIDTH
• RFMXSPECAN_ATTR_NF_MEASUREMENT_INTERVAL
• Averaging
  • RFMXSPECAN_ATTR_NF_AVERAGING_ENABLED
  • RFMXSPECAN_ATTR_NF_AVERAGING_COUNT
• RFMXSPECAN_ATTR_NF_CALIBRATION_SETUP_ID
• External Preamp
  • RFMXSPECAN_ATTR_NF_EXTERNAL_PREAMP_PRESENT
  • RFMXSPECAN_ATTR_NF_EXTERNAL_PREAMP_FREQUENCY
  • RFMXSPECAN_ATTR_NF_EXTERNAL_PREAMP_GAIN
• Loss
  • DUT Input
    • RFMXSPECAN_ATTR_NF_DUT_INPUT_LOSS_COMPENSATION_ENABLED
    • RFMXSPECAN_ATTR_NF_DUT_INPUT_LOSS_FREQUENCY
    • RFMXSPECAN_ATTR_NF_DUT_INPUT_LOSS
    • RFMXSPECAN_ATTR_NF_DUT_INPUT_LOSS_TEMPERATURE
  • DUT Output
    • RFMXSPECAN_ATTR_NF_DUT_OUTPUT_LOSS_COMPENSATION_ENABLED
    • RFMXSPECAN_ATTR_NF_DUT_OUTPUT_LOSS_FREQUENCY
    • RFMXSPECAN_ATTR_NF_DUT_OUTPUT_LOSS
    • RFMXSPECAN_ATTR_NF_DUT_OUTPUT_LOSS_TEMPERATURE
  • Calibration
    • RFMXSPECAN_ATTR_NF_CALIBRATION_LOSS_COMPENSATION_ENABLED
    • RFMXSPECAN_ATTR_NF_CALIBRATION_LOSS_FREQUENCY
    • RFMXSPECAN_ATTR_NF_CALIBRATION_LOSS
    • RFMXSPECAN_ATTR_NF_CALIBRATION_LOSS_TEMPERATURE
• RFMXSPECAN_ATTR_NF_MEASUREMENT_METHOD
• Y Factor
  • RFMXSPECAN_ATTR_NF_Y_FACTOR_MODE
  • Noise Source
    • RFMXSPECAN_ATTR_NF_Y_FACTOR_NOISE_SOURCE_ENR_FREQUENCY
    • RFMXSPECAN_ATTR_NF_Y_FACTOR_NOISE_SOURCE_ENR
    • RFMXSPECAN_ATTR_NF_Y_FACTOR_NOISE_SOURCE_COLD_TEMPERATURE
    • RFMXSPECAN_ATTR_NF_Y_FACTOR_NOISE_SOURCE_OFF_TEMPERATURE
    • RFMXSPECAN_ATTR_NF_Y_FACTOR_NOISE_SOURCE_SETTLING_TIME
    • Loss
      • RFMXSPECAN_ATTR_NF_Y_FACTOR_NOISE_SOURCE_LOSS_COMPENSATION_ENABLED
      • RFMXSPECAN_ATTR_NF_Y_FACTOR_NOISE_SOURCE_LOSS_FREQUENCY
      • RFMXSPECAN_ATTR_NF_Y_FACTOR_NOISE_SOURCE_LOSS
      • RFMXSPECAN_ATTR_NF_Y_FACTOR_NOISE_SOURCE_LOSS_TEMPERATURE
• Cold Source
  • RFMXSPECAN_ATTR_NF_COLD_SOURCE_MODE
  • Input Termination
    • RFMXSPECAN_ATTR_NF_COLD_SOURCE_INPUT_TERMINATION_VSWR
    • RFMXSPECAN_ATTR_NF_COLD_SOURCE_INPUT_TERMINATION_VSWR_FREQUENCY
    • RFMXSPECAN_ATTR_NF_COLD_SOURCE_INPUT_TERMINATION_TEMPERATURE
  • DUT
    • RFMXSPECAN_ATTR_NF_COLD_SOURCE_DUT_S_PARAMETERS_FREQUENCY
    • RFMXSPECAN_ATTR_NF_COLD_SOURCE_DUT_S21
    • RFMXSPECAN_ATTR_NF_COLD_SOURCE_DUT_S12
    • RFMXSPECAN_ATTR_NF_COLD_SOURCE_DUT_S11
    • RFMXSPECAN_ATTR_NF_COLD_SOURCE_DUT_S22
• RFMXSPECAN_ATTR_NF_ADVANCED_DEVICE_TEMPERATURE_TOLERANCE
• RFMXSPECAN_ATTR_NF_NUMBER_OF_ANALYSIS_THREADS
• Results
  • DUT
    • RFMXSPECAN_ATTR_NF_RESULTS_DUT_NOISE_FIGURE
    • RFMXSPECAN_ATTR_NF_RESULTS_DUT_NOISE_TEMPERATURE
    • RFMXSPECAN_ATTR_NF_RESULTS_DUT_GAIN
  • RFMXSPECAN_ATTR_NF_RESULTS_ANALYZER_NOISE_FIGURE
  • Y Factor
    • RFMXSPECAN_ATTR_NF_RESULTS_MEASUREMENT_Y_FACTOR
    • RFMXSPECAN_ATTR_NF_RESULTS_CALIBRATION_Y_FACTOR
    • RFMXSPECAN_ATTR_NF_RESULTS_Y_FACTOR_HOT_POWER
    • RFMXSPECAN_ATTR_NF_RESULTS_Y_FACTOR_COLD_POWER
  • Cold Source
    • RFMXSPECAN_ATTR_NF_RESULTS_COLD_SOURCE_POWER

Data Type:	int32
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeI32 RFmxSpecAn_GetAttributeI32
Description:	Enables the noise figure (NF) measurement. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is RFMXSPECAN_VAL_FALSE. Get Function: RFmxSpecAn_NFGetMeasurementEnabled Set Function: RFmxSpecAn_NFSetMeasurementEnabled

Data Type:	int32
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeI32 RFmxSpecAn_GetAttributeI32
Description:	Specifies the type of DUT. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is RFMXSPECAN_VAL_NF_DUT_TYPE_AMPLIFIER. Get Function: RFmxSpecAn_NFGetDUTType Set Function: RFmxSpecAn_NFSetDUTType
Values:

RFMXSPECAN_VAL_NF_DUT_TYPE_AMPLIFIER (0)	Specifies that the DUT only amplifies or attenuates the signal, and does not change the frequency.
RFMXSPECAN_VAL_NF_DUT_TYPE_DOWNCONVERTER (1)	Specifies that the DUT is a downconverter, that is, the IF frequency is the difference between the LO and RF frequencies.
RFMXSPECAN_VAL_NF_DUT_TYPE_UPCONVERTER (2)	Specifies that the DUT is an upconverter, that is, the IF frequency is the sum of LO and RF frequencies.

Data Type:	float64
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeF64 RFmxSpecAn_GetAttributeF64
Description:	Specifies the fixed LO frequency of the DUT when you set the RFMXSPECAN_ATTR_NF_DUT_TYPE attribute to either RFMXSPECAN_VAL_NF_DUT_TYPE_DOWNCONVERTER or RFMXSPECAN_VAL_NF_DUT_TYPE_UPCONVERTER. This value is expressed in Hz. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is 10 MHz. Get Function: RFmxSpecAn_NFGetFrequencyConverterLOFrequency Set Function: RFmxSpecAn_NFSetFrequencyConverterLOFrequency

Data Type:	int32
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeI32 RFmxSpecAn_GetAttributeI32
Description:	Specifies the context of the NF Frequency List attribute. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is RFMXSPECAN_VAL_NF_FREQUENCY_CONVERTER_FREQUENCY_CONTEXT_RF. Get Function: RFmxSpecAn_NFGetFrequencyConverterFrequencyContext Set Function: RFmxSpecAn_NFSetFrequencyConverterFrequencyContext
Values:

RFMXSPECAN_VAL_NF_FREQUENCY_CONVERTER_FREQUENCY_CONTEXT_RF (0)	Specifies that the frequency context is RF.
RFMXSPECAN_VAL_NF_FREQUENCY_CONVERTER_FREQUENCY_CONTEXT_IF (1)	Specifies that the frequency context is IF.

Data Type:	int32
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeI32 RFmxSpecAn_GetAttributeI32
Description:	Specifies the sideband when you set the RFMXSPECAN_ATTR_NF_DUT_TYPE attribute to either RFMXSPECAN_VAL_NF_DUT_TYPE_DOWNCONVERTER or RFMXSPECAN_VAL_NF_DUT_TYPE_UPCONVERTER, and the RFMXSPECAN_ATTR_NF_FREQUENCY_CONVERTER_FREQUENCY_CONTEXT attribute to RFMXSPECAN_VAL_NF_FREQUENCY_CONVERTER_FREQUENCY_CONTEXT_IF. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is RFMXSPECAN_VAL_NF_FREQUENCY_CONVERTER_SIDEBAND_LSB. Get Function: RFmxSpecAn_NFGetFrequencyConverterSideband Set Function: RFmxSpecAn_NFSetFrequencyConverterSideband
Values:

RFMXSPECAN_VAL_NF_FREQUENCY_CONVERTER_SIDEBAND_LSB (0)	When the frequency context is IF, out of the two possible input frequencies that gets translated to IF, the lower is treated as the RF (signal) frequency while the higher is treated as the image frequency.
RFMXSPECAN_VAL_NF_FREQUENCY_CONVERTER_SIDEBAND_USB (1)	When the frequency context is IF, out of the two possible input frequencies that gets translated to IF, the lower is treated as the image frequency while the higher is treated as the RF (signal) frequency.

Data Type:	float64
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeF64 RFmxSpecAn_GetAttributeF64
Description:	Specifies the gain ratio of the DUT at the image frequency to that at the RF frequency. This value is expressed in dB. Refer to NF concept help for more details. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is 999.99 dB. Get Function: RFmxSpecAn_NFGetFrequencyConverterImageRejection Set Function: RFmxSpecAn_NFSetFrequencyConverterImageRejection

Data Type:	float64 []
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeF64Array RFmxSpecAn_GetAttributeF64Array
Description:	Specifies the list of frequencies at which the noise figure (NF) of the DUT is computed. This value is expressed in Hz. The default value is an empty array. Get Function: RFmxSpecAn_NFGetFrequencyList Set Function: RFmxSpecAn_NFSetFrequencyList

Data Type:	float64
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeF64 RFmxSpecAn_GetAttributeF64
Description:	Specifies the effective noise-bandwidth in which power measurements are performed for the noise figure (NF) measurement. This value is expressed in Hz. The default value is 100 kHz. Get Function: RFmxSpecAn_NFGetMeasurementBandwidth Set Function: RFmxSpecAn_NFSetMeasurementBandwidth

Data Type:	float64
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeF64 RFmxSpecAn_GetAttributeF64
Description:	Specifies the duration for which the signals are acquired at each frequency which you specify in the RFMXSPECAN_ATTR_NF_FREQUENCY_LIST attribute. This value is expressed in seconds. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is 1 ms. Get Function: RFmxSpecAn_NFGetMeasurementInterval Set Function: RFmxSpecAn_NFSetMeasurementInterval

Data Type:	int32
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeI32 RFmxSpecAn_GetAttributeI32
Description:	Specifies whether to enable averaging for the noise figure (NF) measurement. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is RFMXSPECAN_VAL_NF_AVERAGING_ENABLED_FALSE. Get Function: RFmxSpecAn_NFGetAveragingEnabled Set Function: RFmxSpecAn_NFSetAveragingEnabled
Values:

RFMXSPECAN_VAL_NF_AVERAGING_ENABLED_FALSE (0)	The measurement is performed on a single acquisition.
RFMXSPECAN_VAL_NF_AVERAGING_ENABLED_TRUE (1)	The NF measurement uses the value of the RFMXSPECAN_ATTR_NF_AVERAGING_COUNT attribute as the number of acquisitions for each frequency which you specify in the RFMXSPECAN_ATTR_NF_FREQUENCY_LIST attribute, over which the NF measurement is averaged.

Data Type:	int32
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeI32 RFmxSpecAn_GetAttributeI32
Description:	Specifies the number of acquisitions used for averaging when you set the RFMXSPECAN_ATTR_NF_AVERAGING_ENABLED attribute to RFMXSPECAN_VAL_NF_AVERAGING_ENABLED_TRUE. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is 10. Get Function: RFmxSpecAn_NFGetAveragingCount Set Function: RFmxSpecAn_NFSetAveragingCount

Data Type:	char []
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeString RFmxSpecAn_GetAttributeString
Description:	Associates a unique string identifier with the hardware setup used to perform calibration for the NF measurement. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is an empty string. Get Function: RFmxSpecAn_NFGetCalibrationSetupId Set Function: RFmxSpecAn_NFSetCalibrationSetupId

Data Type:	int32
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeI32 RFmxSpecAn_GetAttributeI32
Description:	Specifies if an external preamplifier is present in the signal path. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is RFMXSPECAN_VAL_NF_EXTERNAL_PREAMP_PRESENT_FALSE. Get Function: RFmxSpecAn_NFGetExternalPreampPresent Set Function: RFmxSpecAn_NFSetExternalPreampPresent
Values:

RFMXSPECAN_VAL_NF_EXTERNAL_PREAMP_PRESENT_FALSE (0)	No external preamplifier present in the signal path.
RFMXSPECAN_VAL_NF_EXTERNAL_PREAMP_PRESENT_TRUE (1)	An external preamplifier present in the signal path.

Data Type:	float64 []
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeF64Array RFmxSpecAn_GetAttributeF64Array
Description:	Specifies the array of frequencies corresponding to the value of the RFMXSPECAN_ATTR_NF_EXTERNAL_PREAMP_GAIN attribute. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. Get Function: RFmxSpecAn_NFGetExternalPreampFrequency Set Function: RFmxSpecAn_NFSetExternalPreampFrequency

Data Type:	float64 []
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeF64Array RFmxSpecAn_GetAttributeF64Array
Description:	Specifies the gain of the external preamp as a function of frequency. The value is expressed in dB. Specify the frequencies at which gain values were measured using the RFMXSPECAN_ATTR_NF_EXTERNAL_PREAMP_FREQUENCY attribute. Get Function: RFmxSpecAn_NFGetExternalPreampGain Set Function: RFmxSpecAn_NFSetExternalPreampGain

Data Type:	int32
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeI32 RFmxSpecAn_GetAttributeI32
Description:	Specifies whether the noise figure (NF) measurement accounts for ohmic losses between the noise source and the input port of the DUT, excluding the losses that are common to calibration and the measurement steps for the Y-Factor method, which are specified by the RFMXSPECAN_ATTR_NF_Y_FACTOR_NOISE_SOURCE_LOSS attribute. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is RFMXSPECAN_VAL_NF_DUT_INPUT_LOSS_COMPENSATION_ENABLED_FALSE. Get Function: RFmxSpecAn_NFGetDUTInputLossCompensationEnabled Set Function: RFmxSpecAn_NFSetDUTInputLossCompensationEnabled
Values:

RFMXSPECAN_VAL_NF_DUT_INPUT_LOSS_COMPENSATION_ENABLED_FALSE (0)	The NF measurement ignores the ohmic losses.
RFMXSPECAN_VAL_NF_DUT_INPUT_LOSS_COMPENSATION_ENABLED_TRUE (1)	The NF measurement accounts for the ohmic losses.

Data Type:	float64 []
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeF64Array RFmxSpecAn_GetAttributeF64Array
Description:	Specifies an array of frequencies corresponding to the value of the RFMXSPECAN_ATTR_NF_DUT_INPUT_LOSS attribute. This value is expressed in Hz. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is an empty array. Get Function: RFmxSpecAn_NFGetDUTInputLossFrequency Set Function: RFmxSpecAn_NFSetDUTInputLossFrequency

Data Type:	float64 []
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeF64Array RFmxSpecAn_GetAttributeF64Array
Description:	Specifies an array of the ohmic losses between the noise source and the input port of the DUT, as a function of the frequency. This value is expressed in dB. This loss is accounted for by the NF measurement when you set the RFMXSPECAN_ATTR_NF_DUT_INPUT_LOSS_COMPENSATION_ENABLED attribute to RFMXSPECAN_VAL_NF_DUT_INPUT_LOSS_COMPENSATION_ENABLED_TRUE. You must exclude any loss which is inherent to the noise source and is common between the calibration and measurement steps, and configure the loss using the RFMXSPECAN_ATTR_NF_Y_FACTOR_NOISE_SOURCE_LOSS attribute. Specify the frequencies at which the losses were measured using the RFMXSPECAN_ATTR_NF_DUT_INPUT_LOSS_FREQUENCY attribute. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is an empty array. Get Function: RFmxSpecAn_NFGetDUTInputLoss Set Function: RFmxSpecAn_NFSetDUTInputLoss

Data Type:	float64
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeF64 RFmxSpecAn_GetAttributeF64
Description:	Specifies the physical temperature of the ohmic loss elements considered in the RFMXSPECAN_ATTR_NF_DUT_INPUT_LOSS attribute. This value is expressed in kelvin. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is 297. Get Function: RFmxSpecAn_NFGetDUTInputLossTemperature Set Function: RFmxSpecAn_NFSetDUTInputLossTemperature

Data Type:	int32
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeI32 RFmxSpecAn_GetAttributeI32
Description:	Specifies whether the noise figure (NF) measurement accounts for ohmic losses between the output port of the DUT and the input port of the analyzer. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is RFMXSPECAN_VAL_NF_DUT_OUTPUT_LOSS_COMPENSATION_ENABLED_FALSE. Get Function: RFmxSpecAn_NFGetDUTOutputLossCompensationEnabled Set Function: RFmxSpecAn_NFSetDUTOutputLossCompensationEnabled
Values:

RFMXSPECAN_VAL_NF_DUT_OUTPUT_LOSS_COMPENSATION_ENABLED_FALSE (0)	The NF measurement ignores ohmic losses.
RFMXSPECAN_VAL_NF_DUT_OUTPUT_LOSS_COMPENSATION_ENABLED_TRUE (1)	The NF measurement accounts for the ohmic losses.

Data Type:	float64 []
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeF64Array RFmxSpecAn_GetAttributeF64Array
Description:	Specifies the array of frequencies corresponding to the value of the RFMXSPECAN_ATTR_NF_DUT_OUTPUT_LOSS attribute. This value is expressed in Hz. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is an empty array. Get Function: RFmxSpecAn_NFGetDUTOutputLossFrequency Set Function: RFmxSpecAn_NFSetDUTOutputLossFrequency

Data Type:	float64 []
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeF64Array RFmxSpecAn_GetAttributeF64Array
Description:	Specifies the array of ohmic losses between the output port of the DUT and the input port of the analyzer, as a function of frequency. This value is expressed in dB. This loss is accounted for by the noise figure (NF) measurement when you set the RFMXSPECAN_ATTR_NF_DUT_OUTPUT_LOSS_COMPENSATION_ENABLED attribute to RFMXSPECAN_VAL_NF_DUT_OUTPUT_LOSS_COMPENSATION_ENABLED_TRUE. Specify the array of frequencies at which the losses were measured using the RFMXSPECAN_ATTR_NF_DUT_OUTPUT_LOSS_FREQUENCY attribute. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is an empty array. Get Function: RFmxSpecAn_NFGetDUTOutputLoss Set Function: RFmxSpecAn_NFSetDUTOutputLoss

Data Type:	float64
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeF64 RFmxSpecAn_GetAttributeF64
Description:	Specifies the physical temperature of the ohmic loss elements specified by the RFMXSPECAN_ATTR_NF_DUT_OUTPUT_LOSS attribute. This value is expressed in kelvin. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is 297. Get Function: RFmxSpecAn_NFGetDUTOutputLossTemperature Set Function: RFmxSpecAn_NFSetDUTOutputLossTemperature

Data Type:	int32
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeI32 RFmxSpecAn_GetAttributeI32
Description:	Specifies whether the noise figure (NF) measurement accounts for the ohmic losses between the noise source and input port of the analyzer during the calibration step, excluding any losses which you have specified using the RFMXSPECAN_ATTR_NF_Y_FACTOR_NOISE_SOURCE_LOSS attribute. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is RFMXSPECAN_VAL_NF_CALIBRATION_LOSS_COMPENSATION_ENABLED_FALSE. Get Function: RFmxSpecAn_NFGetCalibrationLossCompensationEnabled Set Function: RFmxSpecAn_NFSetCalibrationLossCompensationEnabled
Values:

RFMXSPECAN_VAL_NF_CALIBRATION_LOSS_COMPENSATION_ENABLED_FALSE (0)	The NF measurement ignores the ohmic losses.
RFMXSPECAN_VAL_NF_CALIBRATION_LOSS_COMPENSATION_ENABLED_TRUE (1)	The NF measurement accounts for the ohmic losses.

Data Type:	float64 []
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeF64Array RFmxSpecAn_GetAttributeF64Array
Description:	Specifies an array of frequencies corresponding to the ohmic losses between the source and the input port of the analyzer. This value is expressed in Hz. This attribute is applicable only when you set the RFMXSPECAN_ATTR_NF_Y_FACTOR_MODE attribute to RFMXSPECAN_VAL_NF_Y_FACTOR_MODE_CALIBRATE and set the RFMXSPECAN_ATTR_NF_MEASUREMENT_METHOD attribute to RFMXSPECAN_VAL_NF_MEASUREMENT_METHOD_Y_FACTOR, or when you set the RFMXSPECAN_ATTR_NF_COLD_SOURCE_MODE attribute to RFMXSPECAN_VAL_NF_Y_FACTOR_MODE_CALIBRATE and set the RFMXSPECAN_ATTR_NF_MEASUREMENT_METHOD attribute to RFMXSPECAN_VAL_NF_MEASUREMENT_METHOD_COLD_SOURCE. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is an empty array. Get Function: RFmxSpecAn_NFGetCalibrationLossFrequency Set Function: RFmxSpecAn_NFSetCalibrationLossFrequency

Data Type:	float64 []
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeF64Array RFmxSpecAn_GetAttributeF64Array
Description:	Specifies the array of ohmic losses between the noise source and input port of the analyzer during calibration, as a function of frequency. This value is expressed in dB. This loss is accounted for by the noise figure (NF) measurement when you set the RFMXSPECAN_ATTR_NF_CALIBRATION_LOSS_COMPENSATION_ENABLED attribute to RFMXSPECAN_VAL_NF_CALIBRATION_LOSS_COMPENSATION_ENABLED_TRUE. You must exclude any loss specified by the RFMXSPECAN_ATTR_NF_Y_FACTOR_NOISE_SOURCE_LOSS attribute. This attribute specifies the frequencies at which the RFMXSPECAN_ATTR_NF_CALIBRATION_LOSS_FREQUENCY attribute measures the losses. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is an empty array. Get Function: RFmxSpecAn_NFGetCalibrationLoss Set Function: RFmxSpecAn_NFSetCalibrationLoss

Data Type:	float64
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeF64 RFmxSpecAn_GetAttributeF64
Description:	Specifies the physical temperature of the ohmic loss elements specified by the RFMXSPECAN_ATTR_NF_CALIBRATION_LOSS attribute. This value is expressed in kelvin. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is 297. Get Function: RFmxSpecAn_NFGetCalibrationLossTemperature Set Function: RFmxSpecAn_NFSetCalibrationLossTemperature

Data Type:	int32
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeI32 RFmxSpecAn_GetAttributeI32
Description:	Specifies the measurement method used to perform the noise figure (NF) measurement. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is Y-Factor. Get Function: RFmxSpecAn_NFGetMeasurementMethod Set Function: RFmxSpecAn_NFSetMeasurementMethod
Values:

RFMXSPECAN_VAL_NF_MEASUREMENT_METHOD_Y_FACTOR (0)	The NF measurement computes the noise figure of the DUT using a noise source with a calibrated excess-noise ratio (ENR). Supported Devices: PXIe-5665 (3.6 GHz), PXIe-5668, PXIe-5644/5645/5646, PXIe-5840/5841, PXIe 5830/5831/5832 Refer to the NF concept topic for more information.
RFMXSPECAN_VAL_NF_MEASUREMENT_METHOD_COLD_SOURCE (1)	The NF measurement computes the noise figure of the DUT using a 50 ohm microwave termination as the noise source. Supported Devices: PXIe-5644/5645/5646/5840/5841, PXIe-5830/5831/5832 Refer to the NF concept topic for more information.

Data Type:	int32
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeI32 RFmxSpecAn_GetAttributeI32
Description:	Specifies whether the measurement should calibrate the noise characteristics of the analyzer or compute the noise characteristics of the DUT when you set the RFMXSPECAN_ATTR_NF_MEASUREMENT_METHOD attribute to RFMXSPECAN_VAL_NF_MEASUREMENT_METHOD_Y_FACTOR. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is RFMXSPECAN_VAL_NF_Y_FACTOR_MODE_MEASURE. Get Function: RFmxSpecAn_NFGetYFactorMode Set Function: RFmxSpecAn_NFSetYFactorMode
Values:

RFMXSPECAN_VAL_NF_Y_FACTOR_MODE_MEASURE (0)	The noise figure (NF) measurement computes the noise characteristics of the DUT, compensating for the noise figure of the analyzer.
RFMXSPECAN_VAL_NF_Y_FACTOR_MODE_CALIBRATE (1)	The NF measurement computes the noise characteristics of the analyzer.

Data Type:	float64 []
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeF64Array RFmxSpecAn_GetAttributeF64Array
Description:	Specifies an array of frequencies corresponding to the effective noise ratio (ENR) values specified by the RFMXSPECAN_ATTR_NF_Y_FACTOR_NOISE_SOURCE_ENR attribute. This value is expressed in Hz. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is an empty array. Get Function: RFmxSpecAn_NFGetYFactorNoiseSourceENRFrequency Set Function: RFmxSpecAn_NFSetYFactorNoiseSourceENRFrequency

Data Type:	float64 []
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeF64Array RFmxSpecAn_GetAttributeF64Array
Description:	Specifies the array of effective noise ratio (ENR) values of the noise source as a function of the frequency. This value is expressed in dB. The corresponding frequencies are specified by the RFMXSPECAN_ATTR_NF_Y_FACTOR_NOISE_SOURCE_ENR_FREQUENCY attribute. This attribute is used only when you set the RFMXSPECAN_ATTR_NF_MEASUREMENT_METHOD attribute to RFMXSPECAN_VAL_NF_MEASUREMENT_METHOD_Y_FACTOR. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is an empty array. Get Function: RFmxSpecAn_NFGetYFactorNoiseSourceENR Set Function: RFmxSpecAn_NFSetYFactorNoiseSourceENR

Data Type:	float64
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeF64 RFmxSpecAn_GetAttributeF64
Description:	Specifies the calibrated cold noise temperature of the noise source used in the Y-Factor method. This value is expressed in kelvin. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is 302.8. Get Function: RFmxSpecAn_NFGetYFactorNoiseSourceColdTemperature Set Function: RFmxSpecAn_NFSetYFactorNoiseSourceColdTemperature

Data Type:	float64
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeF64 RFmxSpecAn_GetAttributeF64
Description:	Specifies the physical temperature of the noise source used in the Y-Factor method when the noise source is turned off. This value is expressed in kelvin. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is 297. Get Function: RFmxSpecAn_NFGetYFactorNoiseSourceOffTemperature Set Function: RFmxSpecAn_NFSetYFactorNoiseSourceOffTemperature

Data Type:	float64
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeF64 RFmxSpecAn_GetAttributeF64
Description:	Specifies the time to wait till the noise source used in the Y-Factor method settles to either hot or cold state when the noise source is turned on or off. This value is expressed in seconds. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is 0. Get Function: RFmxSpecAn_NFGetYFactorNoiseSourceSettlingTime Set Function: RFmxSpecAn_NFSetYFactorNoiseSourceSettlingTime

Data Type:	int32
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeI32 RFmxSpecAn_GetAttributeI32
Description:	Specifies whether the noise figure (NF) measurement should account for ohmic losses inherent to the noise source used in the Y-Factor method common to the calibration and measurement steps. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is RFMXSPECAN_VAL_NF_Y_FACTOR_NOISE_SOURCE_LOSS_COMPENSATION_ENABLED_FALSE. Get Function: RFmxSpecAn_NFGetYFactorNoiseSourceLossCompensationEnabled Set Function: RFmxSpecAn_NFSetYFactorNoiseSourceLossCompensationEnabled
Values:

RFMXSPECAN_VAL_NF_Y_FACTOR_NOISE_SOURCE_LOSS_COMPENSATION_ENABLED_FALSE (0)	Ohmic losses are ignored.
RFMXSPECAN_VAL_NF_Y_FACTOR_NOISE_SOURCE_LOSS_COMPENSATION_ENABLED_TRUE (1)	Ohmic losses are accounted for in the NF measurement.

Data Type:	float64 []
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeF64Array RFmxSpecAn_GetAttributeF64Array
Description:	Specifies the frequencies corresponding to the ohmic loss inherent to the noise source used in the Y-Factor method specified by the RFMXSPECAN_ATTR_NF_Y_FACTOR_NOISE_SOURCE_LOSS attribute. This value is expressed in Hz. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is an empty array. Get Function: RFmxSpecAn_NFGetYFactorNoiseSourceLossFrequency Set Function: RFmxSpecAn_NFSetYFactorNoiseSourceLossFrequency

Data Type:	float64 []
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeF64Array RFmxSpecAn_GetAttributeF64Array
Description:	Specifies an array of the ohmic losses inherent to the noise source used in the Y-Factor method. This value is expressed in dB. This loss is accounted for by the NF measurement when you set the RFMXSPECAN_ATTR_NF_Y_FACTOR_NOISE_SOURCE_LOSS_COMPENSATION_ENABLED attribute to RFMXSPECAN_VAL_NF_Y_FACTOR_NOISE_SOURCE_LOSS_COMPENSATION_ENABLED_TRUE. You must specify the frequencies at which the losses were measured using the RFMXSPECAN_ATTR_NF_Y_FACTOR_NOISE_SOURCE_LOSS_FREQUENCY attribute. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is an empty array. Get Function: RFmxSpecAn_NFGetYFactorNoiseSourceLoss Set Function: RFmxSpecAn_NFSetYFactorNoiseSourceLoss

Data Type:	float64
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeF64 RFmxSpecAn_GetAttributeF64
Description:	Specifies the physical temperature of the ohmic loss elements specified in the RFMXSPECAN_ATTR_NF_Y_FACTOR_NOISE_SOURCE_LOSS attribute. This value is expressed in kelvin. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is 297. Get Function: RFmxSpecAn_NFGetYFactorNoiseSourceLossTemperature Set Function: RFmxSpecAn_NFSetYFactorNoiseSourceLossTemperature

Data Type:	int32
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeI32 RFmxSpecAn_GetAttributeI32
Description:	Specifies whether the measurement should calibrate the noise characteristics of the analyzer or compute the noise characteristics of the DUT for the cold source method. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is RFMXSPECAN_VAL_NF_COLD_SOURCE_MODE_MEASURE. Get Function: RFmxSpecAn_NFGetColdSourceMode Set Function: RFmxSpecAn_NFSetColdSourceMode
Values:

RFMXSPECAN_VAL_NF_COLD_SOURCE_MODE_MEASURE (0)	The noise figure (NF) measurement computes the noise characteristics of the DUT and compensates for the noise figure of the analyzer.
RFMXSPECAN_VAL_NF_COLD_SOURCE_MODE_CALIBRATE (1)	The NF measurement computes the noise characteristics of the analyzer.

Data Type:	float64 []
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeF64Array RFmxSpecAn_GetAttributeF64Array
Description:	Specifies an array of voltage standing wave ratios (VSWR) as a function of frequency of the microwave termination used as the noise source in cold source method. The corresponding array of frequencies is specified by the RFMXSPECAN_ATTR_NF_COLD_SOURCE_INPUT_TERMINATION_VSWR_FREQUENCY attribute. In most cases, the exact VSWR of the microwave termination may not be known. Hence, NI recommends that you set this attribute to an empty array, in which case the noise figure (NF) measurement assumes that the VSWR of the microwave termination is unity for all frequencies. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is an empty array. Get Function: RFmxSpecAn_NFGetColdSourceInputTerminationVSWR Set Function: RFmxSpecAn_NFSetColdSourceInputTerminationVSWR

Data Type:	float64 []
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeF64Array RFmxSpecAn_GetAttributeF64Array
Description:	Specifies an array of frequencies corresponding to the voltage standing wave ratios (VSWR) of the microwave termination used in the cold source method as specified by the RFMXSPECAN_ATTR_NF_COLD_SOURCE_INPUT_TERMINATION_VSWR attribute. This value is expressed in Hz. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is an empty array. Get Function: RFmxSpecAn_NFGetColdSourceInputTerminationVSWRFrequency Set Function: RFmxSpecAn_NFSetColdSourceInputTerminationVSWRFrequency

Data Type:	float64
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeF64 RFmxSpecAn_GetAttributeF64
Description:	Specifies the physical temperature of the microwave termination used as the noise source in the cold source method. This value is expressed in kelvin. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is 297. Get Function: RFmxSpecAn_NFGetColdSourceInputTerminationTemperature Set Function: RFmxSpecAn_NFSetColdSourceInputTerminationTemperature

Data Type:	float64 []
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeF64Array RFmxSpecAn_GetAttributeF64Array
Description:	Specifies an array of frequencies corresponding to the s-parameters of the DUT specified by the RFMXSPECAN_ATTR_NF_COLD_SOURCE_DUT_S21, RFMXSPECAN_ATTR_NF_COLD_SOURCE_DUT_S12, RFMXSPECAN_ATTR_NF_COLD_SOURCE_DUT_S11, and RFMXSPECAN_ATTR_NF_COLD_SOURCE_DUT_S22 attributes. This value is expressed in Hz. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is an empty array. Get Function: RFmxSpecAn_NFGetColdSourceDUTSParametersFrequency Set Function: RFmxSpecAn_NFSetColdSourceDUTSParametersFrequency

Data Type:	float64 []
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeF64Array RFmxSpecAn_GetAttributeF64Array
Description:	Specifies an array of the gains of the DUT as a function of frequency, when the output port of the DUT is terminated with an impedance equal to the characteristic impedance. This value is expressed in dB. The corresponding array of frequencies is specified by the RFMXSPECAN_ATTR_NF_COLD_SOURCE_DUT_S_PARAMETERS_FREQUENCY attribute. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is an empty array. Get Function: RFmxSpecAn_NFGetColdSourceDUTS21 Set Function: RFmxSpecAn_NFSetColdSourceDUTS21

Data Type:	float64 []
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeF64Array RFmxSpecAn_GetAttributeF64Array
Description:	Specifies an array of the input-isolations of the DUT as a function of frequency, when the input port of the DUT is terminated with an impedance equal to the characteristic impedance. This value is expressed in dB. The corresponding array of frequencies is specified by the RFMXSPECAN_ATTR_NF_COLD_SOURCE_DUT_S_PARAMETERS_FREQUENCY attribute. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is an empty array. Get Function: RFmxSpecAn_NFGetColdSourceDUTS12 Set Function: RFmxSpecAn_NFSetColdSourceDUTS12

Data Type:	float64 []
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeF64Array RFmxSpecAn_GetAttributeF64Array
Description:	Specifies an array of the input-reflections of the DUT as a function of frequency, when the output port of the DUT is terminated with an impedance equal to the characteristic impedance. This value is expressed in dB. The corresponding array of frequencies is specified by the RFMXSPECAN_ATTR_NF_COLD_SOURCE_DUT_S_PARAMETERS_FREQUENCY attribute. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is an empty array. Get Function: RFmxSpecAn_NFGetColdSourceDUTS11 Set Function: RFmxSpecAn_NFSetColdSourceDUTS11

Data Type:	float64 []
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeF64Array RFmxSpecAn_GetAttributeF64Array
Description:	Specifies an array of the output-reflections of the DUT as a function of frequency, when the input port of the DUT is terminated with an impedance equal to the characteristic impedance. This value is expressed in dB. The corresponding array of frequencies is specified by the RFMXSPECAN_ATTR_NF_COLD_SOURCE_DUT_S_PARAMETERS_FREQUENCY attribute. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is an empty array. Get Function: RFmxSpecAn_NFGetColdSourceDUTS22 Set Function: RFmxSpecAn_NFSetColdSourceDUTS22

Data Type:	float64
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeF64 RFmxSpecAn_GetAttributeF64
Description:	Specifies the tolerance for device temperature beyond which the calibration data is considered invalid. This value is expressed in Celsius. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector Strings topic for information about the string syntax for named signals. The default value is 5. Get Function: RFmxSpecAn_NFGetAdvancedDeviceTemperatureTolerance Set Function: RFmxSpecAn_NFSetAdvancedDeviceTemperatureTolerance

Data Type:	int32
Access:	read/write
Functions:	RFmxSpecAn_SetAttributeI32 RFmxSpecAn_GetAttributeI32
Description:	Specifies the maximum number of threads used for parallelism for the noise figure (NF) measurement. The number of threads can range from 1 to the number of physical cores. The number of threads you set may not be used in calculations. The actual number of threads used depends on the problem size, system resources, data availability, and other considerations. The default value is 1. Get Function: RFmxSpecAn_NFGetNumberOfAnalysisThreads Set Function: RFmxSpecAn_NFSetNumberOfAnalysisThreads

Data Type:	float64 []
Access:	read only
Functions:	RFmxSpecAn_GetAttributeF64Array
Description:	Returns an array of the noise figures of the DUT measured at the frequencies specified by the RFMXSPECAN_ATTR_NF_FREQUENCY_LIST attribute. This value is expressed in dB. You do not need to use a selector string to read this result for default signal and result instance. Refer to the Selector Strings topic for information about the string syntax for named signals and results. Get Function: RFmxSpecAn_NFGetResultsDUTNoiseFigure

Data Type:	float64 []
Access:	read only
Functions:	RFmxSpecAn_GetAttributeF64Array
Description:	Returns an array of the equivalent thermal noise temperatures of the DUT measured at the frequencies specified by the RFMXSPECAN_ATTR_NF_FREQUENCY_LIST attribute. This value is expressed in kelvin. You do not need to use a selector string to read this result for default signal and result instance. Refer to the Selector Strings topic for information about the string syntax for named signals and results. Get Function: RFmxSpecAn_NFGetResultsDUTNoiseTemperature

Data Type:	float64 []
Access:	read only
Functions:	RFmxSpecAn_GetAttributeF64Array
Description:	Returns an array of the available gains of the DUT measured at the frequencies specified by the RFMXSPECAN_ATTR_NF_FREQUENCY_LIST attribute. This value is expressed in dB. You do not need to use a selector string to read this result for default signal and result instance. Refer to the Selector Strings topic for information about the string syntax for named signals and results. Get Function: RFmxSpecAn_NFGetResultsDUTGain

Data Type:	float64 []
Access:	read only
Functions:	RFmxSpecAn_GetAttributeF64Array
Description:	Returns an array of the noise figures of the analyzer measured at the frequencies specified by the RFMXSPECAN_ATTR_NF_FREQUENCY_LIST attribute. This value is expressed in dB. You do not need to use a selector string to read this result for default signal and result instance. Refer to the Selector Strings topic for information about the string syntax for named signals and results. Get Function: RFmxSpecAn_NFGetResultsAnalyzerNoiseFigure

Data Type:	float64 []
Access:	read only
Functions:	RFmxSpecAn_GetAttributeF64Array
Description:	Returns an array of the measurement Y-Factors measured at the frequencies specified by the RFMXSPECAN_ATTR_NF_FREQUENCY_LIST attribute. This value is expressed in dB. A valid result is returned only when you set the RFMXSPECAN_ATTR_NF_MEASUREMENT_METHOD attribute to RFMXSPECAN_VAL_NF_MEASUREMENT_METHOD_Y_FACTOR. You do not need to use a selector string to read this result for default signal and result instance. Refer to the Selector Strings topic for information about the string syntax for named signals and results. Get Function: RFmxSpecAn_NFGetResultsMeasurementYFactor

Data Type:	float64 []
Access:	read only
Functions:	RFmxSpecAn_GetAttributeF64Array
Description:	Returns an array of the calibration Y-Factors measured at the frequencies specified by the RFMXSPECAN_ATTR_NF_FREQUENCY_LIST attribute. This value is expressed in dB. A valid result is returned only when you set the RFMXSPECAN_ATTR_NF_MEASUREMENT_METHOD attribute to RFMXSPECAN_VAL_NF_MEASUREMENT_METHOD_Y_FACTOR. You do not need to use a selector string to read this result for default signal and result instance. Refer to the Selector Strings topic for information about the string syntax for named signals and results. Get Function: RFmxSpecAn_NFGetResultsCalibrationYFactor

Data Type:	float64 []
Access:	read only
Functions:	RFmxSpecAn_GetAttributeF64Array
Description:	Returns the array of powers measured at the frequencies specified by the RFMXSPECAN_ATTR_NF_FREQUENCY_LIST attribute, when the noise source is enabled. This value is expressed in dBm. A valid result is returned only when you set the RFMXSPECAN_ATTR_NF_MEASUREMENT_METHOD attribute to RFMXSPECAN_VAL_NF_MEASUREMENT_METHOD_Y_FACTOR. You do not need to use a selector string to read this result for default signal and result instance. Refer to the Selector Strings topic for information about the string syntax for named signals and results. Get Function: RFmxSpecAn_NFGetResultsYFactorHotPower

Data Type:	float64 []
Access:	read only
Functions:	RFmxSpecAn_GetAttributeF64Array
Description:	Returns the array of powers measured at the frequencies specified by the RFMXSPECAN_ATTR_NF_FREQUENCY_LIST attribute, when the noise source is disabled. This value is expressed in dBm. A valid result is returned only when you set the RFMXSPECAN_ATTR_NF_MEASUREMENT_METHOD attribute to RFMXSPECAN_VAL_NF_MEASUREMENT_METHOD_Y_FACTOR. You do not need to use a selector string to read this result for default signal and result instance. Refer to the Selector Strings topic for information about the string syntax for named signals and results. Get Function: RFmxSpecAn_NFGetResultsYFactorColdPower

Data Type:	float64 []
Access:	read only
Functions:	RFmxSpecAn_GetAttributeF64Array
Description:	Returns the power measured at the frequencies specified by the RFMXSPECAN_ATTR_NF_FREQUENCY_LIST attribute. This value is expressed in dBm. A valid result is returned only when you set the RFMXSPECAN_ATTR_NF_MEASUREMENT_METHOD attribute to Cold-source. You do not need to use a selector string to read this result for default signal and result instance. Refer to the Selector Strings topic for information about the string syntax for named signals and results. Get Function: RFmxSpecAn_NFGetResultsColdSourcePower