MKS Gen_L

• MKS Gen L - Basics
  • A basic introduction to the functionality of MKS Gen L 1.0 and how to program with Marlin firmware.
• MKS Gen L - Micro Switch Endstop
  • This is a brief tutorial on how to connect a Micro switch and program and test with marlin firmware and Pronterface.
• MKS Gen L - Endstop
  • Explain basic end stop switch sensors and how to enable and load correctly in Marlin Firmware on MKS Gen L 1.0
• MKS Gen L - Optical Endstop
  • This will explains the basic process of using a optical end stop on MKS Gen L 1.0.
• MKS Gen L - A4988 Stepper Configuration
  • This is a quick tutorial on how to install an A4988.
• MKS Gen L - DRV8825 Stepper Configuration
  • This explains how to install a DRV8825 stepper driver and basic NEMA17 installation and test with an switch endstop on the MKS Gen L 1.0 board.
• MKS Gen L - RepRap Discount Smart Controller
  • This is a tutorial on how to add an RepRap discount smart controller LCD on the MKS Gen L 1.0 3d printer board.
• MKS Gen L - External Driver
  • This will explains the basic process of adding an External Stepper to the MKS Gen L 1.0 board. It also explains how to add an addition stepper.
• MKS Gen L - Adding a third extruder for a diamond print head
  • This is a basic tutorial on how to add a third stepper extruder to the MKS Gen L 1.0.
• MKS Gen L - Cooling Fan
  • This is a video explaining how to install a cooling fan and test.
• MKS Gen L - TFT 28 LCD Touch Screen
  • This is a simple tutorial on how to install and test a MKS TFT28 LCD on a MKS Gen L version 1.0.
• MKS Gen L - Hall Effect Sensor
  • This will explains the basic process of using a Hall Effect Sensor on MKS Gen L v1.0.
• MKS Gen L - Servo(s)
  • This video explains how to setup a servo(s) on MKS Gen L v1.0
• MKS Gen L - Parallel Motor Module
  • This is a brief tutorial on how to break a stepper motor output into two Nema 17 motors ports.
  • This does not explain how to tune stepper board for using divided stepper outputs.
• MKS Gen L - Extruder Fan and Fan (EFF)
  • This is a simple tutorial on how to connect and use an extruder fan and fan.
• MKS Gen L - A4988 Calibration
  • This is a somewhat simple way to calibrate your A4988 stepper driver board.
  • Keep in mind it's not perfect, but will allow you to get very close to a good configuration.
• MKS Gen L - DRV8825 Calibration
  • This tutorial will explain the process of calibrating a DRV8825.
• MKS Gen L - BLTouch
  • This is a brief tutorial on how to install and load Marlin firmware on the MKS Gen L v1.0
• MKS Gen L - Dual Axis Steppers
  • The purpose of this tutorial is to use Marlin firmware to enable dual Z-axis stepper motors on MKS GEN L version 1.0.
• MKS Gen L - Extruder Extruder and Fan (EEF)
  • This is a simple tutorial on how to connect and use an extruder extruder and fan.
• MKS Gen L - Ferrule
  • This is a brief video to demonstrate safer wiring connectors.
• MKS Gen L - Extruder Extruder Fan and Bed (EEFB)
  • This is a simple tutorial on how to connect and use an extruder extruder fan and heat bed.
• MKS Gen L - Fan Extender
  • This is a brief tutorial on how to add additional fans beyond the normal two fans.
• MKS Gen L - Fan Extender Hotend cooling
  • This is a basic tutorial on using fan extender and Marlin firmware to cool hotends.
• MKS Gen L - Marlin 1 1 9 (configuration.h)
  • This is a basic tutorial on the Marlin firmware Configure.h tab for MKS Gen L v1.0.
• MKS Gen L - 3D Touch
  • This is a brief tutorial on how to install 3DTouch on MKS Gen L version 1.0..
• MKS Gen L - Pins Debugging
  • This is a brief tutorial on how to troubleshoot pins on a MKS Gen L v 1.0 using Marlin firmware.
• MKS Gen L - REPRAP DISCOUNT FULL GRAPHIC SMART CONTROLLER
  • This is a tutorial on how to add an RepRap discount full graphics smart controller LCD on the MKS Gen L 1.0 3d printer board.
• MKS Gen L - Mixed Steppers A4988 and DRV8825
  • This is a basic tutorial explaining how to install A4988 and DRV8825 in MKS Gen L printer board configuration using Marlin firmware version 1.1.9