Plugwise Binding - jfederico/openhab GitHub Wiki

• Introduction
• Binding installation
• openHAB 1.8 (OH1)
• openHAB 2.0 (OH2)
• Binding configuration
• Stick configuration
• Device configuration
• Binding configuration example
• Item configuration
• Syntax
• Commands
• Variables
• Item configuration example
• Sitemap with example items
• Known issues
• Change log

The Plugwise binding adds support to openHAB for Plugwise ZigBee devices using the Stick.

The binding supports the following Plugwise devices:

• Circle, a power outlet plug that provides energy measurement and switching control of appliances
• Circle+, a special Circle that coordinates the ZigBee network and acts as network gateway
• Scan, a wireless motion (PIR) and light sensor
• Sense, a wireless temperature and humidity sensor
• Stealth, a Circle with a more compact form factor that can be built-in
• Stick, the ZigBee USB controller that openHAB uses to communicate with the Circle+
• Switch, a wireless wall switch

Users should use the Plugwise Source software to define the network, reset devices, perform firmware upgrade, and so forth, e.g. anything which requires user input or interactivity.

Currently only "V2" of the Plugwise protocol is supported. It is adviced that users of the binding upgrade their devices to the latest firmware using the Plugwise Source software.

This is the latest stable release of openHAB.

1. Follow Getting Started for installation of OH1.
2. To use the Plugwise Binding extract org.openhab.binding.serial-1.8.3.jar and org.openhab.binding.plugwise-1.8.3.jar from distribution-1.8.3-addons.zip to the openHAB addons directory.

The latest development version of the binding (1.9.0) can also be used with OH1 by downloading it from the openHAB build server.

Version 2.0 is the openHAB development version. It may be a little buggy but it looks better with its Basic UI and Paper UI.

1. Follow the Demo Tutorial for installation of OH2.
2. To use the Plugwise Binding, open Paper UI, click on Extensions, scroll down the list until you see the Plugwise Binding and click on its Install button.

The latest development version of the binding (1.9.0) is already part of OH2.

Before the binding can be used, the serial port of the Stick needs to be configured. This is done by uncommenting stick.port and assigning a proper value to it in the (binding) configuration file:

OH1: configurations/openhab.cfg

OH2: conf/services/plugwise.cfg

• In OH1 all Plugwise binding configuration keys are prefixed with plugwise:. In OH2 this prefix is optional.
• In OH2 you can also configure the Stick in Paper UI via Configuration > Bindings > Plugwise Binding > Configure.
• To determine the serial port in Linux, insert the Stick, then execute the dmesg command. The last few lines of the output will contain the USB port of the Stick (e.g. ttyUSB0). In Windows the Device Manager lists it in the Ports (COM & LPT) section.

The Plugwise device configuration is also stored in the (binding) configuration file. The binding does not (yet) support automatic device type detection. When no devices are configured, the binding assumes each device to be a Circle. In version 1.9.0 support was added for other device types. These need to be configured in the configuration file. The configuration file also allows you to assign names to MAC addresses of Plugwise devices. This makes Item configurations easier to understand.

Below follows an example configuration with all possible device types. It is also used for the Item configuration example.

############################## Plugwise Binding #######################################
#
# the serial port of the Stick, e.g. "COM1" for Windows or "/dev/ttyUSB0" for Linux
# "stick" is reserved Plugwise ID
plugwise:stick.port=/dev/ttyUSB0
# interval in ms to wait between messages sent on the ZigBee network
#plugwise:stick.interval=150

# you can also name your device circleplus and omit the line specifying the circleplus type (backwards compatibility)
plugwise:lamp.mac=000D6F0000A1B1C1
plugwise:lamp.type=circleplus

# the default device type is circle, so in this case the type could be ommitted (backwards compatibility)
plugwise:fan.mac=000D6F0000A2B2C2
plugwise:fan.type=circle

plugwise:motionsensor.mac=000D6F0000A3B3C3
plugwise:motionsensor.type=scan

plugwise:climatesensor.mac=000D6F0000A4B4C4
plugwise:climatesensor.type=sense

plugwise:fridge.mac=000D6F0000A5B5C5
plugwise:fridge.type=stealth

plugwise:lightswitches.mac=000D6F0000A6B6C6
plugwise:lightswitches.type=switch

• The device .type= configuration option is available since version 1.9.0 of the binding. In older versions of the binding a Circle+ is configured by giving it the name circleplus.
• openHAB may need to be restarted when you change the stick.port or device configurations.
• The MACs are stickered to the back of Plugwise devices. The binding uses full MACs i.e. also the fine print on the sticker. If you don't want to get off your chair, climb up ladders and unplug devices all across your home, causing all sorts of havoc; you can also find them in Source. Open Settings > Appliances. Then double click on an appliance. Click on the little Circle icon to the right of the short Address to see the details of a module and the full MAC (Address). Similarly the MACs of a Scan, Sense and Switch can also be obtained from the Appliances screen by double clicking them in the Sensors and other modules list.

The Plugwise Binding binds Plugwise devices to openHAB items. This is done using a binding specific syntax in the openHAB item configuration files. The item configuration files are stored in:

OH1: configurations/items

OH2: conf/items

The syntax below uses the following elements:

• <command> is an OnOff type command/variable, i.e. either ON or OFF
• <plugwise id> corresponds with the device name (from the device configuration, i.e. plugwise:<plugwise id>.mac=[MAC]) or the full MAC address
• <plugwise command> is the command to be send to the Plugwise device when <command> is received
• <plugwise variable> is a device status variable polled or pushed from the device and stored in an Item
• <polling interval> is the interval in seconds to poll the given variable

The binding syntax for OH1 and OH2 is the same.

Mains powered devices (Circle(+), Stealth) are polled by the binding for their state.

The syntax for items that trigger OnOff commands is:

plugwise="[<command>:<plugwise id>:<plugwise command>:<polling interval>], [<command>:<plugwise id>:<plugwise command>:<polling interval>], ..."

The syntax for items that store a device status variable is:

plugwise="[<plugwise id>:<plugwise variable>:<polling interval>], [<plugwise id>:<plugwise variable>:<polling interval>], ..."

Battery powered devices (Scan, Sense, Switch) push their state to the binding.

The syntax for items that have an OnOff state have is:

plugwise="[<command>:<plugwise id>:<plugwise variable>], [<command>:<plugwise id>:<plugwise variable>], ..."

The syntax for items that store a device status variable is:

plugwise="[<plugwise id>:<plugwise variable>], [<plugwise id>:<plugwise variable>], ..."

Valid <plugwise command>'s are:

Valid <plugwise variable>s are:

For each device type, command and variable type an example is given below. This example uses the devices defined in the Binding configuration example.

/* Circle+ */
Switch Lamp_Switch "Switch" <switch> { plugwise="[ON:lamp:state:15], [OFF:lamp:state:15]" }
String Lamp_Clock "Clock [%s]" <clock> { plugwise="[lamp:clock:15]"}
Number Lamp_Power "Power [%.1f W]" <energy> { plugwise="[lamp:power:10]"}
DateTime Lamp_Power_Stamp "Power stamp [%1$tY-%1$tm-%1$td %1$tH:%1$tM:%1$tS]" <calendar> { plugwise="[lamp:power-stamp:15]"}
Number Lamp_Last_Hour "Last hour [%.3f kWh]" <chart> { plugwise="[lamp:lasthour:60]"}
DateTime Lamp_Last_Hour_Stamp "Last hour stamp [%1$tY-%1$tm-%1$td %1$tH:%1$tM:%1$tS]" <calendar> { plugwise="[lamp:lasthour-stamp:60]"}
DateTime Lamp_Real_Time_Clock "Real time clock [%1$tY-%1$tm-%1$td %1$tH:%1$tM:%1$tS]" <clock> { plugwise="[lamp:realtime-clock:60]"}


/* Circle or Stealth */
Switch Fan_Switch "Switch" <switch> { plugwise="[ON:fan:state:15], [OFF:fan:state:15]" }
String Fan_Clock "Clock [%s]" <clock> { plugwise="[fan:clock:15]" }
Number Fan_Power "Power [%.1f W]" <energy> { plugwise="[fan:power:10]" }
DateTime Fan_Power_Stamp "Power stamp [%1$tY-%1$tm-%1$td %1$tH:%1$tM:%1$tS]" <calendar> { plugwise="[fan:power-stamp:15]" }
Number Fan_Last_Hour "Last hour [%.3f kWh]" <chart> { plugwise="[fan:lasthour:60]" }
DateTime Fan_Last_Hour_Stamp "Last hour stamp [%1$tY-%1$tm-%1$td %1$tH:%1$tM:%1$tS]" <calendar> { plugwise="[fan:lasthour-stamp:60]" }


/* Scan */
Switch Motion_Sensor_Switch "Triggered [%s]" <switch> { plugwise="[ON:motionsensor:triggered], [OFF:motionsensor:triggered]" }
DateTime Motion_Sensor_Triggered_Stamp "Triggered stamp [%1$tY-%1$tm-%1$td %1$tH:%1$tM:%1$tS]" <calendar> { plugwise="[motionsensor:triggered-stamp]" }
DateTime Motion_Sensor_Last_Seen "Last seen [%1$tY-%1$tm-%1$td %1$tH:%1$tM:%1$tS]" <clock> { plugwise="[motionsensor:lastseen]" }


/* Sense */
Switch Climate_Sensor_Switch "Triggered [%s]" <switch> { plugwise="[ON:climatesensor:triggered], [OFF:climatesensor:triggered]" }
DateTime Climate_Sensor_Triggered_Stamp "Triggered stamp [%1$tY-%1$tm-%1$td %1$tH:%1$tM:%1$tS]" <calendar> { plugwise="[climatesensor:triggered-stamp]" }
Number Climate_Sensor_Humidity "Humidity [%.1f %%]" <humidity> { plugwise="[climatesensor:humidity]" }
DateTime Climate_Sensor_Humidity_Stamp "Humidity stamp [%1$tY-%1$tm-%1$td %1$tH:%1$tM:%1$tS]" <calendar> { plugwise="[climatesensor:humidity-stamp]" }
Number Climate_Sensor_Temperature "Temperature [%.1f °C]" <temperature> { plugwise="[climatesensor:temperature]" }
DateTime Climate_Sensor_Temperature_Stamp "Temperature stamp [%1$tY-%1$tm-%1$td %1$tH:%1$tM:%1$tS]" <calendar> { plugwise="[climatesensor:temperature-stamp]" }
DateTime Climate_Sensor_Last_Seen "Last seen [%1$tY-%1$tm-%1$td %1$tH:%1$tM:%1$tS]" <clock> { plugwise="[climatesensor:lastseen]" }


/* Switch */
Switch Light_Switches_Left_Button_State "Left button [%s]" <switch> { plugwise="[ON:lightswitches:left-button-state], [OFF:lightswitches:left-button-state]" }
DateTime Light_Switches_Left_Button_State_Stamp "Left button stamp [%1$tY-%1$tm-%1$td %1$tH:%1$tM:%1$tS]" <calendar> { plugwise="[lightswitches:left-button-state-stamp]" }
Switch Light_Switches_Right_Button_State "Right button [%s]" <switch> { plugwise="[ON:lightswitches:right-button-state], [OFF:lightswitches:right-button-state]" }
DateTime Light_Switches_Right_Button_State_Stamp "Right button stamp [%1$tY-%1$tm-%1$td %1$tH:%1$tM:%1$tS]" <calendar> { plugwise="[lightswitches:right-button-state-stamp]" }
DateTime Light_Switches_Last_Seen "Last seen [%1$tY-%1$tm-%1$td %1$tH:%1$tM:%1$tS]" <clock> { plugwise="[lightswitches:lastseen]" }

A MAC can be used instead of a device name, e.g. fan can be replaced with 000D6F0000A2B2C2:

Number Fan_Power "Power [%.1f W]" <energy> { plugwise="[000D6F0000A2B2C2:power:10]" }

You can now add all these items to a sitemap as shown in the example below. Sitemaps are located in:

OH1: configurations/sitemaps

OH2: conf/sitemaps

sitemap default label="Main Menu"
{

    Frame label="Lamp (Circle+)" {
	    Switch item=Lamp_Switch
	    Text item=Lamp_Clock
	    Text item=Lamp_Power
	    Text item=Lamp_Power_Stamp
	    Text item=Lamp_Last_Hour
	    Text item=Lamp_Last_Hour_Stamp
	    Text item=Lamp_Real_Time_Clock
    }

    Frame label="Fan (Circle)" {
	    Switch item=Fan_Switch
	    Text item=Fan_Clock
	    Text item=Fan_Power
	    Text item=Fan_Power_Stamp
	    Text item=Fan_Last_Hour
	    Text item=Fan_Last_Hour_Stamp
    }

    Frame label="Motion Sensor (Scan)" {
	    Text item=Motion_Sensor_Switch
	    Text item=Motion_Sensor_Triggered_Stamp
	    Text item=Motion_Sensor_Last_Seen
    }

    Frame label="Climate Sensor (Sense)" {
	    Text item=Climate_Sensor_Switch
	    Text item=Climate_Sensor_Triggered_Stamp
	    Text item=Climate_Sensor_Humidity
	    Text item=Climate_Sensor_Humidity_Stamp
	    Text item=Climate_Sensor_Temperature
	    Text item=Climate_Sensor_Temperature_Stamp
	    Text item=Climate_Sensor_Last_Seen
    }

    Frame label="Light Switches (Switch)" {
	    Text item=Light_Switches_Left_Button_State
	    Text item=Light_Switches_Left_Button_State_Stamp
	    Text item=Light_Switches_Right_Button_State
	    Text item=Light_Switches_Right_Button_State_Stamp
	    Text item=Light_Switches_Last_Seen
    }

}

Click on a thumbnail below to see how this sitemap is rendered in the various openHAB user interfaces.

OH1 Classic UI	OH2 Classic UI	OH2 Basic UI

• OH2: When you rename or remove devices from plugwise.cfg they are still persisted in openHAB. To fix this enter config:delete Plugwise in the openHAB console and restart openHAB. This will clear the persisted Plugwise configuration and reload it from plugwise.cfg

• Issue #456 - Various fixes of Plugwise binding (#11)
• Change Plugwise Binding from AbstractBinding to AbstractActiveBinding + Fix issue #456 (#40)
• Fixes for issues #649, #496 and #497 (#810)
• Further improvement of Quartz Job scheduling (#812)
• Fix configuration file parsing, quartz scheduling problem (#823)

• Various fixes (#850)

• Clean up logging (#4122)
• Fix #1003: High CPU load (#4162)
• Add support for Scan, Sense, Stealth and Switch #4565 (#4586)
• Add openHAB 2 feature addon (#4644)
• NullPointerException may occur when concurrent threads get PlugwiseDevice from Stick (#4648)