Invoke ADCUpdateNspbr - j81blog/J81.ADCToolkit GitHub Wiki

Invoke-ADCUpdateNspbr

SYNOPSIS

Update NS configuration Object.

SYNTAX

Invoke-ADCUpdateNspbr [-Name] <String> [[-Action] <String>] [[-Srcip] <Boolean>] [[-Srcipop] <String>]
 [[-Srcipval] <String>] [[-Srcport] <Boolean>] [[-Srcportop] <String>] [[-Srcportval] <String>]
 [[-Destip] <Boolean>] [[-Destipop] <String>] [[-Destipval] <String>] [[-Destport] <Boolean>]
 [[-Destportop] <String>] [[-Destportval] <String>] [[-Nexthop] <Boolean>] [[-Nexthopval] <String>]
 [[-Iptunnel] <Boolean>] [[-Iptunnelname] <String>] [[-Vxlanvlanmap] <String>] [[-Srcmac] <String>]
 [[-Srcmacmask] <String>] [[-Protocol] <String>] [[-Protocolnumber] <Double>] [[-Vlan] <Double>]
 [[-Vxlan] <Double>] [[-Interface] <String>] [[-Priority] <Double>] [[-Msr] <String>] [[-Monitor] <String>]
 [-PassThru] [-WhatIf] [-Confirm] [<CommonParameters>]

DESCRIPTION

Configuration for Policy Based Routing(PBR) entry resource.

EXAMPLES

EXAMPLE 1

Invoke-ADCUpdateNspbr -name <string>

An example how to update nspbr configuration Object(s).

PARAMETERS

-Name

Name for the PBR. Must begin with an ASCII alphabetic or underscore \(_\) character, and must contain only ASCII alphanumeric, underscore, hash \(#\), period \(.\), space, colon \(:\), at \(@\), equals \(=\), and hyphen \(-\) characters. Cannot be changed after the PBR is created.

Type: String
Parameter Sets: (All)
Aliases:

Required: True
Position: 2
Default value: None
Accept pipeline input: False
Accept wildcard characters: False

-Action

Action to perform on the outgoing IPv4 packets that match the PBR. Available settings function as follows:

  • ALLOW - The Citrix ADC sends the packet to the designated next-hop router.
  • DENY - The Citrix ADC applies the routing table for normal destination-based routing. Possible values = ALLOW, DENY
Type: String
Parameter Sets: (All)
Aliases:

Required: False
Position: 3
Default value: None
Accept pipeline input: False
Accept wildcard characters: False

-Srcip

IP address or range of IP addresses to match against the source IP address of an outgoing IPv4 packet. In the command line interface, separate the range with a hyphen. For example: 10.102.29.30-10.102.29.189.

Type: Boolean
Parameter Sets: (All)
Aliases:

Required: False
Position: 4
Default value: False
Accept pipeline input: False
Accept wildcard characters: False

-Srcipop

Either the equals (=) or does not equal (!=) logical operator. Possible values = =, !=, EQ, NEQ

Type: String
Parameter Sets: (All)
Aliases:

Required: False
Position: 5
Default value: None
Accept pipeline input: False
Accept wildcard characters: False

-Srcipval

IP address or range of IP addresses to match against the source IP address of an outgoing IPv4 packet. In the command line interface, separate the range with a hyphen. For example: 10.102.29.30-10.102.29.189.

Type: String
Parameter Sets: (All)
Aliases:

Required: False
Position: 6
Default value: None
Accept pipeline input: False
Accept wildcard characters: False

-Srcport

Port number or range of port numbers to match against the source port number of an outgoing IPv4 packet. In the command line interface, separate the range with a hyphen. For example: 40-90. Note: The destination port can be specified only for TCP and UDP protocols.

Type: Boolean
Parameter Sets: (All)
Aliases:

Required: False
Position: 7
Default value: False
Accept pipeline input: False
Accept wildcard characters: False

-Srcportop

Either the equals (=) or does not equal (!=) logical operator. Possible values = =, !=, EQ, NEQ

Type: String
Parameter Sets: (All)
Aliases:

Required: False
Position: 8
Default value: None
Accept pipeline input: False
Accept wildcard characters: False

-Srcportval

Port number or range of port numbers to match against the source port number of an outgoing IPv4 packet. In the command line interface, separate the range with a hyphen. For example: 40-90. Note: The destination port can be specified only for TCP and UDP protocols.

Type: String
Parameter Sets: (All)
Aliases:

Required: False
Position: 9
Default value: None
Accept pipeline input: False
Accept wildcard characters: False

-Destip

IP address or range of IP addresses to match against the destination IP address of an outgoing IPv4 packet. In the command line interface, separate the range with a hyphen. For example: 10.102.29.30-10.102.29.189.

Type: Boolean
Parameter Sets: (All)
Aliases:

Required: False
Position: 10
Default value: False
Accept pipeline input: False
Accept wildcard characters: False

-Destipop

Either the equals (=) or does not equal (!=) logical operator. Possible values = =, !=, EQ, NEQ

Type: String
Parameter Sets: (All)
Aliases:

Required: False
Position: 11
Default value: None
Accept pipeline input: False
Accept wildcard characters: False

-Destipval

IP address or range of IP addresses to match against the destination IP address of an outgoing IPv4 packet. In the command line interface, separate the range with a hyphen. For example: 10.102.29.30-10.102.29.189.

Type: String
Parameter Sets: (All)
Aliases:

Required: False
Position: 12
Default value: None
Accept pipeline input: False
Accept wildcard characters: False

-Destport

Port number or range of port numbers to match against the destination port number of an outgoing IPv4 packet. In the command line interface, separate the range with a hyphen. For example: 40-90. Note: The destination port can be specified only for TCP and UDP protocols.

Type: Boolean
Parameter Sets: (All)
Aliases:

Required: False
Position: 13
Default value: False
Accept pipeline input: False
Accept wildcard characters: False

-Destportop

Either the equals (=) or does not equal (!=) logical operator. Possible values = =, !=, EQ, NEQ

Type: String
Parameter Sets: (All)
Aliases:

Required: False
Position: 14
Default value: None
Accept pipeline input: False
Accept wildcard characters: False

-Destportval

Port number or range of port numbers to match against the destination port number of an outgoing IPv4 packet. In the command line interface, separate the range with a hyphen. For example: 40-90. Note: The destination port can be specified only for TCP and UDP protocols.

Type: String
Parameter Sets: (All)
Aliases:

Required: False
Position: 15
Default value: None
Accept pipeline input: False
Accept wildcard characters: False

-Nexthop

IP address of the next hop router or the name of the link load balancing virtual server to which to send matching packets if action is set to ALLOW. If you specify a link load balancing (LLB) virtual server, which can provide a backup if a next hop link fails, first make sure that the next hops bound to the LLB virtual server are actually next hops that are directly connected to the Citrix ADC. Otherwise, the Citrix ADC throws an error when you attempt to create the PBR. The next hop can be null to represent null routes.

Type: Boolean
Parameter Sets: (All)
Aliases:

Required: False
Position: 16
Default value: False
Accept pipeline input: False
Accept wildcard characters: False

-Nexthopval

The Next Hop IP address or gateway name.

Type: String
Parameter Sets: (All)
Aliases:

Required: False
Position: 17
Default value: None
Accept pipeline input: False
Accept wildcard characters: False

-Iptunnel

The Tunnel name.

Type: Boolean
Parameter Sets: (All)
Aliases:

Required: False
Position: 18
Default value: False
Accept pipeline input: False
Accept wildcard characters: False

-Iptunnelname

The iptunnel name where packets need to be forwarded upon.

Type: String
Parameter Sets: (All)
Aliases:

Required: False
Position: 19
Default value: None
Accept pipeline input: False
Accept wildcard characters: False

-Vxlanvlanmap

The vlan to vxlan mapping to be applied for incoming packets over this pbr tunnel.

Type: String
Parameter Sets: (All)
Aliases:

Required: False
Position: 20
Default value: None
Accept pipeline input: False
Accept wildcard characters: False

-Srcmac

MAC address to match against the source MAC address of an outgoing IPv4 packet.

Type: String
Parameter Sets: (All)
Aliases:

Required: False
Position: 21
Default value: None
Accept pipeline input: False
Accept wildcard characters: False

-Srcmacmask

Used to define range of Source MAC address. It takes string of 0 and 1, 0s are for exact match and 1s for wildcard. For matching first 3 bytes of MAC address, srcMacMask value "000000111111". .

Type: String
Parameter Sets: (All)
Aliases:

Required: False
Position: 22
Default value: None
Accept pipeline input: False
Accept wildcard characters: False

-Protocol

Protocol, identified by protocol name, to match against the protocol of an outgoing IPv4 packet. Possible values = ICMP, IGMP, TCP, EGP, IGP, ARGUS, UDP, RDP, RSVP, EIGRP, L2TP, ISIS, GGP, IPoverIP, ST, CBT, BBN-RCC-M, NVP-II, PUP, EMCON, XNET, CHAOS, MUX, DCN-MEAS, HMP, PRM, XNS-IDP, TRUNK-1, TRUNK-2, LEAF-1, LEAF-2, IRTP, ISO-TP4, NETBLT, MFE-NSP, MERIT-INP, SEP, 3PC, IDPR, XTP, DDP, IDPR-CMTP, TP++, IL, IPv6, SDRP, IPv6-Route, IPv6-Frag, IDRP, GRE, MHRP, BNA, ESP, AH, I-NLSP, SWIPE, NARP, MOBILE, TLSP, SKIP, ICMPV6, IPv6-NoNx, IPv6-Opts, Any-Host-Internal-Protocol, CFTP, Any-Local-Network, SAT-EXPAK, KRYPTOLAN, RVD, IPPC, Any-Distributed-File-System, TFTP, VISA, IPCV, CPNX, CPHB, WSN, PVP, BR-SAT-MO, SUN-ND, WB-MON, WB-EXPAK, ISO-IP, VMTP, SECURE-VM, VINES, TTP, NSFNET-IG, DGP, TCF, OSPFIGP, Sprite-RP, LARP, MTP, AX.25, IPIP, MICP, SCC-SP, ETHERIP, Any-Private-Encryption-Scheme, GMTP, IFMP, PNNI, PIM, ARIS, SCPS, QNX, A/N, IPComp, SNP, Compaq-Pe, IPX-in-IP, VRRP, PGM, Any-0-Hop-Protocol, ENCAP, DDX, IATP, STP, SRP, UTI, SMP, SM, PTP, FIRE, CRTP, CRUDP, SSCOPMCE, IPLT, SPS, PIPE, SCTP, FC, RSVP-E2E-IGNORE, Mobility-Header, UDPLite

Type: String
Parameter Sets: (All)
Aliases:

Required: False
Position: 23
Default value: None
Accept pipeline input: False
Accept wildcard characters: False

-Protocolnumber

Protocol, identified by protocol number, to match against the protocol of an outgoing IPv4 packet.

Type: Double
Parameter Sets: (All)
Aliases:

Required: False
Position: 24
Default value: 0
Accept pipeline input: False
Accept wildcard characters: False

-Vlan

ID of the VLAN. The Citrix ADC compares the PBR only to the outgoing packets on the specified VLAN. If you do not specify any interface ID, the appliance compares the PBR to the outgoing packets on all VLANs.

Type: Double
Parameter Sets: (All)
Aliases:

Required: False
Position: 25
Default value: 0
Accept pipeline input: False
Accept wildcard characters: False

-Vxlan

ID of the VXLAN. The Citrix ADC compares the PBR only to the outgoing packets on the specified VXLAN. If you do not specify any interface ID, the appliance compares the PBR to the outgoing packets on all VXLANs.

Type: Double
Parameter Sets: (All)
Aliases:

Required: False
Position: 26
Default value: 0
Accept pipeline input: False
Accept wildcard characters: False

-Interface

ID of an interface. The Citrix ADC compares the PBR only to the outgoing packets on the specified interface. If you do not specify any value, the appliance compares the PBR to the outgoing packets on all interfaces.

Type: String
Parameter Sets: (All)
Aliases:

Required: False
Position: 27
Default value: None
Accept pipeline input: False
Accept wildcard characters: False

-Priority

Priority of the PBR, which determines the order in which it is evaluated relative to the other PBRs. If you do not specify priorities while creating PBRs, the PBRs are evaluated in the order in which they are created.

Type: Double
Parameter Sets: (All)
Aliases:

Required: False
Position: 28
Default value: 0
Accept pipeline input: False
Accept wildcard characters: False

-Msr

Monitor the route specified byte Next Hop parameter. This parameter is not applicable if you specify a link load balancing (LLB) virtual server name with the Next Hop parameter. Possible values = ENABLED, DISABLED

Type: String
Parameter Sets: (All)
Aliases:

Required: False
Position: 29
Default value: None
Accept pipeline input: False
Accept wildcard characters: False

-Monitor

The name of the monitor.(Can be only of type ping or ARP ).

Type: String
Parameter Sets: (All)
Aliases:

Required: False
Position: 30
Default value: None
Accept pipeline input: False
Accept wildcard characters: False

-PassThru

Return details about the created nspbr item.

Type: SwitchParameter
Parameter Sets: (All)
Aliases:

Required: False
Position: Named
Default value: False
Accept pipeline input: False
Accept wildcard characters: False

-WhatIf

Shows what would happen if the cmdlet runs. The cmdlet is not run.

Type: SwitchParameter
Parameter Sets: (All)
Aliases: wi

Required: False
Position: Named
Default value: None
Accept pipeline input: False
Accept wildcard characters: False

-Confirm

Prompts you for confirmation before running the cmdlet.

Type: SwitchParameter
Parameter Sets: (All)
Aliases: cf

Required: False
Position: Named
Default value: None
Accept pipeline input: False
Accept wildcard characters: False

CommonParameters

This cmdlet supports the common parameters: -Debug, -ErrorAction, -ErrorVariable, -InformationAction, -InformationVariable, -OutVariable, -OutBuffer, -PipelineVariable, -Verbose, -WarningAction, and -WarningVariable. For more information, see about_CommonParameters.

INPUTS

OUTPUTS

NOTES

File Name : Invoke-ADCUpdateNspbr Version : v2111.2521 Author : John Billekens Reference : https://developer-docs.citrix.com/projects/citrix-adc-nitro-api-reference/en/latest/configuration/ns/nspbr/ Requires : PowerShell v5.1 and up ADC 13.x and up. ADC 12 and lower may work, not guaranteed.

RELATED LINKS

https://blog.j81.nl

⚠️ **GitHub.com Fallback** ⚠️