Unset Lsn configuration Object.

Invoke-ADCUnsetLsngroup [[-Groupname] <String>] [[-portblocksize] <Boolean>] [[-logging] <Boolean>]
 [[-sessionlogging] <Boolean>] [[-sessionsync] <Boolean>] [[-snmptraplimit] <Boolean>] [[-ftp] <Boolean>]
 [[-pptp] <Boolean>] [[-sipalg] <Boolean>] [[-rtspalg] <Boolean>] [[-ftpcm] <Boolean>] [-WhatIf] [-Confirm]
 [<CommonParameters>]

Configuration for LSN group resource.

Invoke-ADCUnsetLsngroup -groupname <string>

An example how to unset lsngroup configuration Object(s).

Name for the LSN group. Must begin with an ASCII alphanumeric or underscore (_) character, and must contain only ASCII alphanumeric, underscore, hash (#), period (.), space, colon (:), at (@), equals (=), and hyphen (-) characters. Cannot be changed after the LSN group is created.

Type: String
Parameter Sets: (All)
Aliases:

Required: False
Position: 2
Default value: None
Accept pipeline input: False
Accept wildcard characters: False

Size of the NAT port block to be allocated for each subscriber. To set this parameter for Dynamic NAT, you must enable the port block allocation parameter in the bound LSN pool. For Deterministic NAT, the port block allocation parameter is always enabled, and you cannot disable it. In Dynamic NAT, the Citrix ADC allocates a random NAT port block, from the available NAT port pool of an NAT IP address, for each subscriber. For a subscriber, if all the ports are allocated from the subscriber's allocated port block, the ADC allocates a new random port block for the subscriber. The default port block size is 256 for Deterministic NAT, and 0 for Dynamic NAT.

Type: Boolean
Parameter Sets: (All)
Aliases:

Required: False
Position: 3
Default value: False
Accept pipeline input: False
Accept wildcard characters: False

Log mapping entries and sessions created or deleted for this LSN group. The Citrix ADC logs LSN sessions for this LSN group only when both logging and session logging parameters are enabled. The ADC uses its existing syslog and audit log framework to log LSN information. You must enable global level LSN logging by enabling the LSN parameter in the related NSLOG action and SYLOG action entities. When the Logging parameter is enabled, the Citrix ADC generates log messages related to LSN mappings and LSN sessions of this LSN group. The ADC then sends these log messages to servers associated with the NSLOG action and SYSLOG actions entities. A log message for an LSN mapping entry consists of the following information:

• NSIP address of the Citrix ADC
• Time stamp
• Entry type (MAPPING or SESSION)
• Whether the LSN mapping entry is created or deleted
• Subscriber's IP address, port, and traffic domain ID
• NAT IP address and port
• Protocol name
• Destination IP address, port, and traffic domain ID might be present, depending on the following conditions: ** Destination IP address and port are not logged for Endpoint-Independent mapping ** Only Destination IP address (and not port) is logged for Address-Dependent mapping ** Destination IP address and port are logged for Address-Port-Dependent mapping. Possible values = ENABLED, DISABLED

Type: Boolean
Parameter Sets: (All)
Aliases:

Required: False
Position: 4
Default value: False
Accept pipeline input: False
Accept wildcard characters: False

Log sessions created or deleted for the LSN group. The Citrix ADC logs LSN sessions for this LSN group only when both logging and session logging parameters are enabled. A log message for an LSN session consists of the following information:

• NSIP address of the Citrix ADC
• Time stamp
• Entry type (MAPPING or SESSION)
• Whether the LSN session is created or removed
• Subscriber's IP address, port, and traffic domain ID
• NAT IP address and port
• Protocol name
• Destination IP address, port, and traffic domain ID. Possible values = ENABLED, DISABLED

Type: Boolean
Parameter Sets: (All)
Aliases:

Required: False
Position: 5
Default value: False
Accept pipeline input: False
Accept wildcard characters: False

In a high availability (HA) deployment, synchronize information of all LSN sessions related to this LSN group with the secondary node. After a failover, established TCP connections and UDP packet flows are kept active and resumed on the secondary node (new primary). For this setting to work, you must enable the global session synchronization parameter. Possible values = ENABLED, DISABLED

Type: Boolean
Parameter Sets: (All)
Aliases:

Required: False
Position: 6
Default value: False
Accept pipeline input: False
Accept wildcard characters: False

Maximum number of SNMP Trap messages that can be generated for the LSN group in one minute.

Type: Boolean
Parameter Sets: (All)
Aliases:

Required: False
Position: 7
Default value: False
Accept pipeline input: False
Accept wildcard characters: False

Enable Application Layer Gateway (ALG) for the FTP protocol. For some application-layer protocols, the IP addresses and protocol port numbers are usually communicated in the packet's payload. When acting as an ALG, the Citrix ADC changes the packet's payload to ensure that the protocol continues to work over LSN. Note: The Citrix ADC also includes ALG for ICMP and TFTP protocols. ALG for the ICMP protocol is enabled by default, and there is no provision to disable it. ALG for the TFTP protocol is disabled by default. ALG is enabled automatically for an LSN group when you bind a UDP LSN application profile, with endpoint-independent-mapping, endpoint-independent filtering, and destination port as 69 (well-known port for TFTP), to the LSN group. Possible values = ENABLED, DISABLED

Type: Boolean
Parameter Sets: (All)
Aliases:

Required: False
Position: 8
Default value: False
Accept pipeline input: False
Accept wildcard characters: False

Enable the PPTP Application Layer Gateway. Possible values = ENABLED, DISABLED

Type: Boolean
Parameter Sets: (All)
Aliases:

Required: False
Position: 9
Default value: False
Accept pipeline input: False
Accept wildcard characters: False

Enable the SIP ALG. Possible values = ENABLED, DISABLED

Type: Boolean
Parameter Sets: (All)
Aliases:

Required: False
Position: 10
Default value: False
Accept pipeline input: False
Accept wildcard characters: False

Enable the RTSP ALG. Possible values = ENABLED, DISABLED

Type: Boolean
Parameter Sets: (All)
Aliases:

Required: False
Position: 11
Default value: False
Accept pipeline input: False
Accept wildcard characters: False

Enable the FTP connection mirroring for specified LSN group. Connection mirroring (CM or connection failover) refers to keeping active an established TCP or UDP connection when a failover occurs. Possible values = ENABLED, DISABLED

Type: Boolean
Parameter Sets: (All)
Aliases:

Required: False
Position: 12
Default value: False
Accept pipeline input: False
Accept wildcard characters: False

Shows what would happen if the cmdlet runs. The cmdlet is not run.

Type: SwitchParameter
Parameter Sets: (All)
Aliases: wi

Required: False
Position: Named
Default value: None
Accept pipeline input: False
Accept wildcard characters: False

Prompts you for confirmation before running the cmdlet.

Type: SwitchParameter
Parameter Sets: (All)
Aliases: cf

Required: False
Position: Named
Default value: None
Accept pipeline input: False
Accept wildcard characters: False

This cmdlet supports the common parameters: -Debug, -ErrorAction, -ErrorVariable, -InformationAction, -InformationVariable, -OutVariable, -OutBuffer, -PipelineVariable, -Verbose, -WarningAction, and -WarningVariable. For more information, see about_CommonParameters.

File Name : Invoke-ADCUnsetLsngroup Version : v2111.2521 Author : John Billekens Reference : https://developer-docs.citrix.com/projects/citrix-adc-nitro-api-reference/en/latest/configuration/lsn/lsngroup Requires : PowerShell v5.1 and up ADC 13.x and up. ADC 12 and lower may work, not guaranteed.

https://blog.j81.nl