Unset High Availability configuration Object.

Invoke-ADCUnsetHanode [[-id] <Boolean>] [[-hastatus] <Boolean>] [[-hasync] <Boolean>] [[-haprop] <Boolean>]
 [[-hellointerval] <Boolean>] [[-deadinterval] <Boolean>] [[-failsafe] <Boolean>] [[-maxflips] <Boolean>]
 [[-maxfliptime] <Boolean>] [[-syncvlan] <Boolean>] [[-syncstatusstrictmode] <Boolean>] [-WhatIf] [-Confirm]
 [<CommonParameters>]

Configuration for node resource.

Invoke-ADCUnsetHanode

An example how to unset hanode configuration Object(s).

Number that uniquely identifies the node. For self node, it will always be 0. Peer node values can range from 1-64.

Type: Boolean
Parameter Sets: (All)
Aliases:

Required: False
Position: 2
Default value: False
Accept pipeline input: False
Accept wildcard characters: False

The HA status of the node. The HA status STAYSECONDARY is used to force the secondary device stay as secondary independent of the state of the Primary device. For example, in an existing HA setup, the Primary node has to be upgraded and this process would take few seconds. During the upgradation, it is possible that the Primary node may suffer from a downtime for a few seconds. However, the Secondary should not take over as the Primary node. Thus, the Secondary node should remain as Secondary even if there is a failure in the Primary node. STAYPRIMARY configuration keeps the node in primary state in case if it is healthy, even if the peer node was the primary node initially. If the node with STAYPRIMARY setting (and no peer node) is added to a primary node (which has this node as the peer) then this node takes over as the new primary and the older node becomes secondary. ENABLED state means normal HA operation without any constraints/preferences. DISABLED state disables the normal HA operation of the node. Possible values = ENABLED, STAYSECONDARY, DISABLED, STAYPRIMARY

Type: Boolean
Parameter Sets: (All)
Aliases:

Required: False
Position: 3
Default value: False
Accept pipeline input: False
Accept wildcard characters: False

Automatically maintain synchronization by duplicating the configuration of the primary node on the secondary node. This setting is not propagated. Automatic synchronization requires that this setting be enabled (the default) on the current secondary node. Synchronization uses TCP port 3010. Possible values = ENABLED, DISABLED

Type: Boolean
Parameter Sets: (All)
Aliases:

Required: False
Position: 4
Default value: False
Accept pipeline input: False
Accept wildcard characters: False

Automatically propagate all commands from the primary to the secondary node, except the following:

• All HA configuration related commands. For example, add ha node, set ha node, and bind ha node.
• All Interface related commands. For example, set interface and unset interface.
• All channels related commands. For example, add channel, set channel, and bind channel. The propagated command is executed on the secondary node before it is executed on the primary. If command propagation fails, or if command execution fails on the secondary, the primary node executes the command and logs an error. Command propagation uses port 3010. Note: After enabling propagation, run force synchronization on either node. Possible values = ENABLED, DISABLED

Type: Boolean
Parameter Sets: (All)
Aliases:

Required: False
Position: 5
Default value: False
Accept pipeline input: False
Accept wildcard characters: False

Interval, in milliseconds, between heartbeat messages sent to the peer node. The heartbeat messages are UDP packets sent to port 3003 of the peer node.

Type: Boolean
Parameter Sets: (All)
Aliases:

Required: False
Position: 6
Default value: False
Accept pipeline input: False
Accept wildcard characters: False

Number of seconds after which a peer node is marked DOWN if heartbeat messages are not received from the peer node.

Type: Boolean
Parameter Sets: (All)
Aliases:

Required: False
Position: 7
Default value: False
Accept pipeline input: False
Accept wildcard characters: False

Keep one node primary if both nodes fail the health check, so that a partially available node can back up data and handle traffic. This mode is set independently on each node. Possible values = ON, OFF

Type: Boolean
Parameter Sets: (All)
Aliases:

Required: False
Position: 8
Default value: False
Accept pipeline input: False
Accept wildcard characters: False

Max number of flips allowed before becoming sticky primary.

Type: Boolean
Parameter Sets: (All)
Aliases:

Required: False
Position: 9
Default value: False
Accept pipeline input: False
Accept wildcard characters: False

Interval after which flipping of node states can again start.

Type: Boolean
Parameter Sets: (All)
Aliases:

Required: False
Position: 10
Default value: False
Accept pipeline input: False
Accept wildcard characters: False

Vlan on which HA related communication is sent. This include sync, propagation, connection mirroring, LB persistency config sync, persistent session sync and session state sync. However HA heartbeats can go all interfaces.

Type: Boolean
Parameter Sets: (All)
Aliases:

Required: False
Position: 11
Default value: False
Accept pipeline input: False
Accept wildcard characters: False

strict mode flag for sync status. Possible values = ENABLED, DISABLED

Type: Boolean
Parameter Sets: (All)
Aliases:

Required: False
Position: 12
Default value: False
Accept pipeline input: False
Accept wildcard characters: False

Shows what would happen if the cmdlet runs. The cmdlet is not run.

Type: SwitchParameter
Parameter Sets: (All)
Aliases: wi

Required: False
Position: Named
Default value: None
Accept pipeline input: False
Accept wildcard characters: False

Prompts you for confirmation before running the cmdlet.

Type: SwitchParameter
Parameter Sets: (All)
Aliases: cf

Required: False
Position: Named
Default value: None
Accept pipeline input: False
Accept wildcard characters: False

This cmdlet supports the common parameters: -Debug, -ErrorAction, -ErrorVariable, -InformationAction, -InformationVariable, -OutVariable, -OutBuffer, -PipelineVariable, -Verbose, -WarningAction, and -WarningVariable. For more information, see about_CommonParameters.

File Name : Invoke-ADCUnsetHanode Version : v2111.2521 Author : John Billekens Reference : https://developer-docs.citrix.com/projects/citrix-adc-nitro-api-reference/en/latest/configuration/ha/hanode Requires : PowerShell v5.1 and up ADC 13.x and up. ADC 12 and lower may work, not guaranteed.

https://blog.j81.nl