netdata process priority - hilbix/netdata GitHub Wiki

By default netdata runs with the idle process scheduling policy, so that it uses CPU resources, only when there is idle CPU to spare. On very busy servers (or weak servers), this can lead to gaps on the charts.

setting netdata process scheduling policy

You can set netdata scheduling policy in netdata.conf, like this:

[global]
  process scheduling policy = idle

You can use the following:

policy description
idle use CPU only when there is spare - this is lower than nice 19 - it is the default for netdata and it is so low that netdata will run in "slow motion" under extreme system load, resulting in short (1-2 seconds) gaps at the charts.
other
or
nice 		this is the default policy for all processes under Linux. It provides dynamic priorities based on the nice level of each process. Check below for setting this nice level for netdata.
batch This policy is similar to other in that it schedules the thread according to its dynamic priority (based on the nice value). The difference is that this policy will cause the scheduler to always assume that the thread is CPU-intensive. Consequently, the scheduler will apply a small scheduling penalty with respect to wake-up behavior, so that this thread is mildly disfavored in scheduling decisions.
fifo fifo can be used only with static priorities higher than 0, which means that when a fifo threads becomes runnable, it will always immediately preempt any currently running other, batch, or idle thread. fifo is a simple scheduling algorithm without time slicing.
rr a simple enhancement of fifo. Everything described above for fifo also applies to rr, except that each thread is allowed to run only for a maximum time quantum.
keep
or
none 		do not set scheduling policy, priority or nice level - i.e. keep running with whatever it is set already (e.g. by systemd).

For more information see man sched.

scheduling priority for rr and fifo

Once the policy is set to one of rr or fifo, the following will appear:

[global]
    process scheduling priority = 0

These priorities are usually from 0 to 99. Higher numbers make the process more important.

nice level for policies other or batch

When the policy is set to other, nice, or batch, the following will appear:

[global]
    process nice level = 19

scheduling settings and systemd

netdata will not be able to set its scheduling policy and priority to more important values when it is started as the netdata user (systemd case).

You can set these settings at /etc/systemd/system/netdata.service:

[Service]
# By default netdata switches to scheduling policy idle, which makes it use CPU, only
# when there is spare available.
# Valid policies: other (the system default) | batch | idle | fifo | rr
#CPUSchedulingPolicy=other

# This sets the maximum scheduling priority netdata can set (for policies: rr and fifo).
# netdata (via [global].process scheduling priority in netdata.conf) can only lower this value.
# Priority gets values 1 (lowest) to 99 (highest).
#CPUSchedulingPriority=1

# For scheduling policy 'other' and 'batch', this sets the lowest niceness of netdata.
# netdata (via [global].process nice level in netdata.conf) can only increase the value set here.
#Nice=0

Run systemctl daemon-reload to reload these changes.

Now, tell netdata to keep these settings, as set by systemd, by editing netdata.conf and setting:

[global]
    process scheduling policy = keep

Using the above, whatever scheduling settings you have set at netdata.service will be maintained by netdata.

Example 1: netdata with nice -1 on non-systemd systems

On a system that is not based on systemd, to make netdata run with nice level -1 (a little bit higher to the default for all programs), edit netdata.conf and set:

[global]
  process scheduling policy = other
  process nice level = -1

then execute this to restart netdata:

sudo service netdata restart

Example 2: netdata with nice -1 on systemd systems

On a system that is based on systemd, to make netdata run with nice level -1 (a little bit higher to the default for all programs), edit netdata.conf and set:

[global]
  process scheduling policy = keep

edit /etc/systemd/system/netdata.service and set:

[Service]
CPUSchedulingPolicy=other
Nice=-1

then execute:

sudo systemctl daemon-reload
sudo systemctl restart netdata

analytics

⚠️ **GitHub.com Fallback** ⚠️