Validate optics related streaming telemetry performance monitoring parameters like input power, output power, bias current and so on.

Optics test requirements alongside the platform funtional tests require 2 optics DUT samples each optics part number, connect both two optical ethernet interfaces to Automatic Test Equipment (ATE).

• Connect at least one optical ethernet interface to ATE.

• Step 1: Using components/component/[name=%s]/state get the list of transceivers and validate following leafs are set:

  • /components/component/state/mfg-name

  • /components/component/transceiver/state/form-factor

  • /components/component/state/serial-no

  • /components/component/state/part-no

  • /components/component/state/firmware-version

  • Using /interfaces/interface/state get the list of Interfaces and validate following leafs are set:

    • /interfaces/interface/state/physical-channel
    • /interfaces/interface/state/transceiver

  • Verify that the list of transceivers received are the same. This is only a consistency check that the vendor implemented the model correctly.

    • /components/component/state
    • /interfaces/interface/state/transceiver

• Step 2: Get list of components of type TRANSCEIVER. Verify the instant value is between the corresponding lower and upper thresholds for both [severity]=WARNING and [severity]=CRITICAL. In case of multiple physical channels or lanes relevant PMs like TX and RX power should be reported for all the lanes.

  • Module case temperature
    • /components/component/transceiver/thresholds/threshold/state/module-temperature-lower
    • /components/component/transceiver/thresholds/threshold/state/module-temperature-upper
    • /components/component/transceiver/thresholds/threshold/state/severity
    • /components/component/state/temperature/instant
  • Tx output power
    • /components/component/transceiver/thresholds/threshold/state/output-power-lower
    • /components/component/transceiver/thresholds/threshold/state/output-power-upper
    • /components/component/transceiver/thresholds/threshold/state/severity
    • /components/component/transceiver/physical-channels/channel/state/output-power/instant
  • Rx input power
    • /components/component/transceiver/thresholds/threshold/state/input-power-lower
    • /components/component/transceiver/thresholds/threshold/state/input-power-upper
    • /components/component/transceiver/thresholds/threshold/state/severity
    • /components/component/transceiver/physical-channels/channel/state/input-power/instant
  • Laser bias-current
    • /components/component/transceiver/thresholds/threshold/state/laser-bias-current-lower
    • /components/component/transceiver/thresholds/threshold/state/laser-bias-current-upper
    • /components/component/transceiver/thresholds/threshold/state/severity
    • /components/component/transceiver/physical-channels/channel/state/laser-bias-current/instant

• Step 3:

  • Verify the telemetry is updated after the optics power cycle.
  • Disable the DUT transceiver (power off module 3.3V supply).
  • Verify /interfaces/interface/state/oper-status is DOWN.
  • Enable the DUT transceiver (power on module 3.3V supply)
  • Verify /interfaces/interface/state/oper-status is UP.
  • Repeat Step1 and Step2.

• Step 4: Verify the telemetry is updated after the interface is flapped.

  • Disable/shutdown the interface of the DUT.
  • Verify the optics input power and output power are updated to below the corresponding low alarm threshold.
  • Verify /interfaces/interface/state/oper-status is DOWN
  • Re-enable the interface of the DUT
  • Verify /interfaces/interface/state/oper-status is UP.
  • Repeat Step1 and Step2.

• /interfaces/interface/config/enabled
• /components/component/transceiver/state/enabled (transceiver 3.3V power supply on/off)

• /components/component/transceiver/physical-channels/channel/state/input-power/instant
• /components/component/transceiver/physical-channels/channel/state/output-power/instant
• /components/component/transceiver/physical-channels/channel/state/laser-bias-current/instant
• /components/component/state/temperature/instant
• /components/component/state/mfg-name
• /components/component/transceiver/state/form-factor
• /components/component/state/serial-no
• /components/component/state/part-no
• /components/component/state/firmware-version
• /components/component/transceiver/thresholds/threshold/state/output-power-lower
• /components/component/transceiver/thresholds/threshold/state/output-power-upper
• /components/component/transceiver/thresholds/threshold/state/input-power-lower
• /components/component/transceiver/thresholds/threshold/state/input-power-upper
• /components/component/transceiver/thresholds/threshold/state/module-temperature-lower
• /components/component/transceiver/thresholds/threshold/state/module-temperature-upper
• /components/component/transceiver/thresholds/threshold/state/laser-bias-current-lower
• /components/component/transceiver/thresholds/threshold/state/laser-bias-current-upper
• /components/component/transceiver/thresholds/threshold/state/severity