Test Report (5.0.0) - analogdevicesinc/lnxdsp-adi-meta GitHub Wiki
| 📝 | This test report applies to version 5.0.x. Any regressions specific to a .x release will be explicitly noted |
|---|
| Testing Component | SC598-SOM-EZKIT | SC594-SOM-EZKIT | SC589-MINI | SC573-EZKIT |
|---|---|---|---|---|
| ADAU1962 Audio Out Driver | ✅ | ✅ | ✅ | ✅ |
| USB Gadget Audio | ✅ | ✅ | ✅ | ✅ |
| SHARC ALSA | ✅ | N/A | N/A | N/A |
| remoteproc | ✅ | ✅ | ✅ | ✅ |
| virtio rpmsg | ✅ | ✅ | ✅ | ✅ |
| Common Clock Framework | ✅ | ✅ | ✅ | ✅ |
| Crypto Framework | ➖ | ➖ | N/A | N/A |
| DMA Peripheral Implicitly tested as it's used by SPI, OSPI, and UART drivers | ✅ | ✅ | ✅ | ✅ |
| MDMA Implicitly tested as it's used only by remoteproc to load data to SHARC shared memory | ✅ | ✅ | ✅ | ✅ |
| EMAC0 (eth0) | ✅ | ✅ | ✅ | ✅ |
| EMAC11 | ➖ | ➖ | ➖ | ➖ |
| GPTimers | ✅ | ✅ | ✅ | ✅ |
| I2C | ✅ | ✅ | ✅ | ✅ |
| SRAM/L2 alloc | ✅ | ✅ | ✅ | ✅ |
| SPI | ✅ | ✅ | ✅ | ✅ |
| QSPI Boot | ✅ | ✅ | ✅ | ✅ |
| eMMC dev/mmcblk0 | ➖ | N/A | N/A | N/A |
| eMMC Boot2 | ➖ | N/A | N/A | N/A |
| SD dev/mmcblk0 | ✅ | N/A | ✅ | ✅ |
| SD Boot | ✅ | N/A | ✅ | ✅ |
| OSPI3 | N/A | ✅ | N/A | N/A |
| uart0 | ✅ | ✅ | ✅ | ✅ |
| USB: Host | ✅ | ✅ | ✅ | ✅ |
| USB: Device | ✅ | ✅ | ✅ | ✅ |
| Watchdog | ✅ | ✅ | ✅ | ✅ |
✅: PASS
❗: PASS with warning(s), see note
❌: FAIL, see note
N/A: Not Applicable
➖: Not Tested
1Currently, the driver can enumerate the IP and identify what is present, but the PHY is not configured/reset yet and so ethernet communications do not work.
2Currently, booting with the kernel and RFS on SD/eMMC is the only supported configuration, primarily due to hardware limitations on the SOM-CRR-EZKIT (so U-Boot must still be stored on the SPI flash)
3OSPI is not currently working for MX66 chip under 5.x and 6.x kernel versions. OSPI (1S-8S-8S mode) does work for SC594 & IS25LX256