Info: key combinations - Stephan-S/FS25_AutoDrive GitHub Wiki

Many key combinations can be looked up in the FS25 key assignments and/or can be freely assigned there.

Show/hide mouse pointer: middle mouse button
open/close AD HUD: LALT + Numpad-0
openAD settings: LALT + LCTRL + Numpad-0

Fruit Multiselect

to select various fruits or loads:

  • multiple selection = press and hold LCTRL + LMB on desired list entries
  • delete entry from multiple selection = press and hold LCTRL + LMB on list entry to be deselected
  • deselection = LMB on any unselected/marked list entry
  • select or unselect everything = press and hold LALT + LMB on any list entry

The icon in front of the list selection shows the status, which can be changed by left-clicking (only when multiselect is active):

  • single fruit (white): only one fruit is selected
  • one small and one large fruit (blue): several fruits are selected and the fruit with the most fruit, e.g. in a silo, is always selected first
  • 3 large fruits (blue): several fruits are selected and the fruits are rotated during each loading process

PDA and helper map

if activated in the personal settings:

  • set upper target point: LMB on an AD target point
  • set lower target point: RMB on an AD target point

Parking

  • assign parking lot (in edit mode): LCTRL + RMB on P in the HUD
  • delete parking lot (in edit mode): LALT + RMB on P in the HUD
  • send to parking lot: LMB on P in the HUD

Lines

in edit mode (while driving)

  • record green line: LMB on REC
  • record light blue line (backward): LMB on REC, then drive backward
  • record blue line: RMB on REC
  • record orange line: LShift + LMB on REC
  • record brown line: LShift + RMB on REC
  • NOTE: as soon as you reverse during recording, a reverse line (light blue) will be recorded!

record two lines simultaneously (Dual Recording):

  • only possible if the offset between the lines is not 0
  • LCTRL + LMB on record button = 2 directions of travel normal (green line)
  • LCTRL + RMB on record button = 2 lines that can be traveled on both sides (blue)
  • LCTRL + LShift + LMB on Recordbutton = 2 directions of travel, secondary route normal (orange line)
  • LCTRL + LShift + RMB on record button = 2 double-sided lines as secondary route (brown)

Waypoints

in edit mode

  • show/hide waypoints: press RCTRL
  • create one waypoint: LCTRL + LMB
  • create oneway line: hold down LCTRL and press then LMB to create the waypoints
  • create twoway line: hold down LCTRL + LALT and press then LMB to create the waypoints
  • create oneway secondary< route line: hold down LCTRL + LShift and press then LMB to create the waypoints
  • connect green line: LMB on 1st waypoint, LMB on 2nd waypoint
  • connect blue line: LMB on 2nd waypoint, LMB on 1st waypoint
  • connect orange line: LMB on 1st waypoint, LShift + LMB on 2nd waypoint
  • connect brown line: LMB on 2nd waypoint, LShift + LMB on 1st waypoint
  • connect light blue line (backward): LMB on 1st waypoint, RShift + LMB on 2nd waypoint
  • change waypoint priority: LShift + LMB on waypoint
  • delete waypoint: LALT + LMB on waypoint
  • move waypoint: grab with RMB and move it
  • move waypoint on same altitude: grab with RMB, press and hold LShift, then move the waypoint
  • change waypoints between 2 intersections / behind 1 intersection -> change priority: 1. LMB on crossing waypoint, 2. LShift + LMB on 1st waypoint behind the crossing
  • change waypoints between 2 intersections / behind 1 intersection -> change direction: 1. LMB on crossing waypoint, 2. LCTRL + LMB on 1st waypoint behind the crossing
  • delete waypoints between 2 intersections / behind 1 intersection: 1. LMB on crossing waypoint, 2. LShift + LCTRL + LALT + LMB on 1st waypoint behind the crossing
  • Curve between 2 waypoints: LMB to waypoint, point mouse cursor to the other waypoint, turn mouse wheel until the desired curve is reached and then LMB to the waypoint
  • Delete waypoints in a scalable area:
  • select a waypoint (marked waypoint turns green)
  • press LALT an dhold
  • use the mouse wheel to enlarge or reduce the area to be selected (circle)
  • pressing LMB deletes the selected waypoints
  • release LALT to exit the mode
  • when reactivated, the same area (circle) is set, but can be adjusted

Abbreviations

  • LMB = left mouse button
  • RMB = right mouse button
  • LCTRL = left CTRL key
  • RCTRL = right CTRL key
  • LALT = left ALT key
  • LShift = left Shift key
  • RShift = right Shift key
⚠️ **GitHub.com Fallback** ⚠️