Dragino LSN50 Node - IoTThinks/EasyLoRaWAN GitHub Wiki
Dragino LSN50
To use Dragino LSN50 as LoRaWAN node
- Manual: Dragio LSN50 UserManual 1.6.2 and LSN50_LoRa_Sensor_Node_UserManual_v1.6.2.pdf
- Hardware is Dragino LSN50 v1.0: https://wiki.dragino.com/index.php?title=Lora_Sensor_Node-LSN50
- Internal LoRaST module: https://wiki.dragino.com/index.php?title=LoRa_ST
- All firmware and manuals for LoRaST: http://www.dragino.com/downloads/index.php?dir=LSN50-LoRaST/
1. Hardware
1.1 Pin locations
1.2 Pin mapping for STM32L072CZT6 (used by LSN50)
Original at https://github.com/dragino/Lora/blob/master/LoRaST/v1.0/LoRa%20ST%20v1.0_Sch.pdf
2. Connect to hardware
2.1 Use STLink v2 to upload code / firmware
STLink v2 USB
Driver is at https://www.st.com/en/development-tools/st-link-v2.html#tools-software
Pin mapping
- LSN50 -> STLink v2
- PA14 -> SWCLK
- PA13 -> SWDIO. NOTE: NEXT TO PA13 is PB14. WE NEED PA14!!!
- VCC -> 3.3+
- GND -> GND
Switch of LSN50 is ISP to upload code. It's recommended to remove UART TTL USB before uploading code via STLink
STLink v2 will show up in USB Device, not Ports (COM & LPT)
2.2 Use UART to debug
- LSN50 -> CP1202 USB TTL
- GND -> GND
- PA2 -> RX
- PA3 -> TX
3. Update LoRaWAN firmware
- STM32 Flasher: https://www.st.com/en/development-tools/flasher-stm32.html
- Use USB UART TTL to upload: Plug in battery, switch to ISP and reset board
- After finish uploading, swith to Flash and reset board to run.
Select the first one.
4. Programming guides
3.1 AT Commands
References:
- All LoRaST references: http://www.dragino.com/downloads/index.php?dir=LSN50-LoRaST/
- LSN50 AT Commands v1.6.3: http://www.dragino.com/downloads/downloads/LSN50-LoRaST/DRAGINO_LSN50_AT_Commands_v1.6.3.pdf and DRAGINO_LSN50_AT_Commands_v1.6.3.pdf
Use UART TTL
- Speed 9600
- Data 8 bit, Parity none, Stop bits 1, Flow control none.
To join ABP into Single channel gateway
- AT+FDR Reset Parameters to Factory Default, Keys Reserve
- AT+NJM=0 Set to ABP mode
- AT+ADR=0 Set the Adaptive Data Rate Off
- AT+DR=3 Set Data Rate (SF9, 125Khz)
- AT+TDC=300000 Set transmit interval to 5 minutes
- AT+CHS=433175000 Single channel mode
- AT+RX2FQ=433175000 Frequency for RX2
- AT+DADDR=? Get Device Address to 26 01 1A F1
- AT+CFM=1 ConfirmedDataUp
- ATZ Reset MCU
LoRaWAN Frequency - Use Channel 0
- { 433175000, 125, 7, 12, 433175000, 125, 7, 12}, // Channel 0, 433.175 MHz/125 primary
- { 433375000, 125, 7, 12, 433375000, 125, 7, 12}, // Channel 1, 433.375 MHz primary
- { 433575000, 125, 7, 12, 433575000, 125, 7, 12}, // Channel 2, 433.575 MHz primary
- { 433775000, 125, 7, 12, 433775000, 125, 7, 12}, // Channel 3, 433.775 MHz primary
- { 433975000, 125, 7, 12, 433975000, 125, 7, 12}, // Channel 4, 433.975 MHz primary
- { 434175000, 125, 7, 12, 434175000, 125, 7, 12}, // Channel 5, 434.175 MHz primary
- { 434375000, 125, 7, 12, 434375000, 125, 7, 12}, // Channel 6, 434.375 MHz primary
- { 434575000, 125, 7, 12, 434575000, 125, 7, 12}, // Channel 7, 434.575 MHz primary
- { 434775000, 125, 7, 12, 434775000, 125, 7, 12} // Channel 8, 434.775 MHz primary
Data rate - Use DR3
