SwitchConfigs - Deathraymind/StemLabMK2 GitHub Wiki

Documentation

Trunked and Access Ports Configuration Guide

This documentation provides step-by-step instructions for configuring trunked and access ports on a trunk switch (top switch) and a cyber switch (bottom Brocade switch) using Cisco and Brocade commands. It includes the setup of VLANs, tagging, and port configurations.

1. Terminology

Untagged: Denotes access ports. Traffic on these ports is not encapsulated with VLAN tags.
Tagged: Refers to trunked ports. Traffic on these ports is encapsulated with VLAN tags.
VLAN 10: Represents a virtual interface configured for VLAN 10.

2. Configuration on Trunk Switch (Top Switch)

Red Ports (Multi-VLAN Ports for Switches and Routers):

enable
conf t
vlan 10
tagg e 1/1/1 to 1/1/6
interface e 1/1/1 to 1/1/6
dual-mode 1
exit
exit
write mem

Green Ports (Multi-VLAN Ports with POE for APs):

enable
conf t
vlan 10
tagg e 1/1/7 to 1/1/12
exit
interface e 1/1/7 to 1/1/12
inline power
dual-mode 1
exit
exit
write mem

3. Configuration on Cyber Switch (Bottom Brocade Switch)

Red Ports:

enable
conf t
vlan 10
tagg 1/1/1 to 1/1/6
exit
interface e 1/1/1 to 1/1/6
dual-mode 1
exit
exit
write mem

Blue Ports (Untagged Interfaces for VLAN 10 Devices):

vlan 10
untagg e 1/1/13 to 1/1/24
exit
exit
write mem

4. Additional Terminology and Tips for brocade

Inline Power: Enables Power over Ethernet (POE) on the specified ports.
Dual-Mode 1: Sets the native VLANs on ports to VLAN 1 or the basic LAN configuration.
Module Configuration: Modules must be configured one at a time, specifying 1/x/x format for port identification.
To view available interfaces:
```
enable
show interfaces brief
```

Cisco Switch Configuration

Blue Ports (Configuring VLAN 10):

enable
configure terminal
vlan 10
name Cyber
exit
exit
wr mem

Blue Ports (Configuring Untagged/Access Interface for VLAN 10):

enable
configure terminal
interface range g1/0/1 - g1/0/22
switchport mode access
switchport access vlan 10
exit
exit
wr mem

Red Port (Configuring Tagged/Trunk Interface):

show ip interfaces brief

enable
configure terminal
interface gigabitethernet1/0/23
switchport trunk encapsulation dot1q
switchport mode trunk 
switchport trunk allowed vlan none
switchport trunk allowed vlan add 1
switchport trunk allowed vlan add 10
no shutdown
exit
exit
wr mem

Side Note: The "switchport trunk encapsulation dot1q" command may not be needed, though if this error message shows:

Command rejected: an interface whose trunk encapsulation is "auto" can not be configure

then type in the command.

Cisco Switch WS-C3560X-24U-L Configuration

Blue Ports (Configuring VLAN 10):

enable
configure terminal
vlan 10
name Cyber
exit

Red Ports (Multi-VLAN Ports for Switches and Routers):

enable
configure terminal
interface range g0/1 - 6
switchport trunk encapsulation dot1q
switchport mode trunk
switchport trunk allowed vlan none
switchport trunk allowed vlan add 1
switchport trunk allowed vlan add 10
exit
exit
wr mem

Green Ports (Multi-VLAN Ports with POE for APs):

enable 
configure terminal
interface range g0/7 - 12
power inline auto
switchport trunk encapsulation dot1q
switchport mode trunk
switchport trunk allowed vlan none
switchport trunk allowed vlan add 1
switchport trunk allowed vlan add 10
exit
exit
wr mem

Configuring Management Interface:

enable
configure terminal
interface vlan 10
ip address 172.16.254.11 255.255.0.0
no shut
exit
ip default-gateway 172.16.1.1
exit
wr mem

Configuring SSH

enable
configure terminal
enable secret 1234qwer!@#$QWER
username admin secret amongus
access-list 1 permit 172.16.0.0 0.0.255.255
ip domain name silly.net
hostname DistributionSW
crypto key generate rsa
2048
ip ssh version 2
line vty 0 15
login local
exec-timeout 5 0
transport input ssh
access-class 1 in
exit
exit
wr mem