30% 𝐐𝐌𝐊 Tripple‑Modes 𝐂𝐍𝐂 𝘈𝘭𝘶𝘮𝘪𝘯𝘶𝘮 𝘔𝘦𝘤𝘩𝘢𝘯𝘪𝘤𝘢𝘭 𝘕𝘶𝘮𝘦𝘳𝘪𝘤 𝘒𝘦𝘺𝘣𝘰𝘢𝘳𝘥

◌	ƒn	𝐓𝐀𝐁	← 𝗕𝗞𝗦𝗣	𝗣𝗥𝗧𝗦𝗖	𝗦𝗖𝗥𝗢𝗟𝗟	⏸️ 𝗣𝗔𝗨𝗦𝗘
𝐍𝐔𝐌 🔒	／	∗	－	𝐈𝐍𝐒	🏠 𝗛𝗢𝗠𝗘	𝐏𝐆𝐔𝐏
7	8	9	＋	𝐃𝐄𝐋	𝐄𝐍𝐃	𝐏𝐆𝐃𝐍
4	5	6	＋
1	2	3	𝗘𝗡𝗧𝗘𝗥		⬆️
0	0	𝐃𝐄𝐋	𝗘𝗡𝗧𝗘𝗥	⬅️	⬇️	➡️

◌	ƒn	^ 𝐂𝐓𝐑𝐋	⌥ 𝗼𝗽𝘁𝗶𝗼𝗻	⌘ 𝐂𝐌𝐃	❔	𝐄𝐒𝐂
𝐓𝐀𝐁	∗	F	← 𝗕𝗞𝗦𝗣	𝐈𝐍𝐒	🏠 𝗛𝗢𝗠𝗘	𝐏𝐆𝐔𝐏
Q	W	E	𝗘𝗡𝗧𝗘𝗥	𝐃𝐄𝐋	𝐄𝐍𝐃	𝐏𝐆𝐃𝐍
A	S	D	𝗘𝗡𝗧𝗘𝗥
Z	X	C	𝐒𝐏𝐀𝐂𝐄𝗕𝗔𝗥		⬆️
𝙎𝙝𝙞𝙛𝙩	𝙎𝙝𝙞𝙛𝙩	V	𝐒𝐏𝐀𝐂𝐄𝗕𝗔𝗥	⬅️	⬇️	➡️

• ƒn﹢⬆️＝𝗟𝗘𝗗 backlight brightness increase
• ƒn﹢⬇️＝𝗟𝗘𝗗 backlight brightness decrease
• ƒn﹢⬅️＝𝗟𝗘𝗗 backlight hue increase
• ƒn﹢➡️＝𝗟𝗘𝗗 backlight hue decrease
• ƒn﹢／＝𝗟𝗘𝗗 backlight speed decrease
• ƒn﹢∗＝𝗟𝗘𝗗 backlight speed increase
• ƒn﹢← 𝗕𝗞𝗦𝗣＝Turn OFF／ON the 𝘣𝘢𝘤𝘬𝘭𝘪𝘨𝘩𝘵
• ƒn﹢𝗘𝗡𝗧𝗘𝗥＝Toggle 𝘣𝘢𝘤𝘬𝘭𝘪𝘨𝘩𝘵 mode
• ƒn﹢＋＝𝗟𝗘𝗗 𝘣𝘢𝘤𝘬𝘭𝘪𝘨𝘩𝘵 saturation increase
• ƒn﹢－＝𝗟𝗘𝗗 𝘣𝘢𝘤𝘬𝘭𝘪𝘨𝘩𝘵 saturation decrease
• ƒn﹢𝐏𝐆𝐔𝐏＝Toggle strip light mode
• ƒn﹢𝐏𝐆𝐃𝐍＝Toggle strip light color
• ƒn﹢0＝Long‑press ƒn﹢0 for 3 seconds to reset the keyboard to its factory setting❗♻️

---

• 𝘋𝘦𝘷𝘪𝘤𝘦 𝘍𝘪𝘳𝘮𝘸𝘢𝘳𝘦 𝘜𝘱𝘨𝘳𝘢𝘥𝘦 𝘔𝘰𝘥𝘦: Press＆hold 𝘥𝘪𝘢𝘭‑knob and plug in 𝐔𝐒𝐁 cable…

---

1. 𝑾𝒊𝒓𝒆𝒅 Mode:

• toggle the mode switch to the middle wired mode, and then insert 𝐔𝐒𝐁 cable into your computer, the keyboard 𝘣𝘢𝘤𝘬𝘭𝘪𝘨𝘩𝘵 lights on and turns to the default of 𝐑𝐆𝐁 𝘣𝘢𝘤𝘬𝘭𝘪𝘨𝘩𝘵 effect, it means connection successful.

2. 𝑩𝒍𝒖𝒆𝒕𝒐𝒐𝒕𝒉® 𝘗𝘢𝘪𝘳𝘪𝘯𝘨 Instructions:

• Perform the following steps to pair this keyboard with your device(s):
  1. 𝐂𝐈𝐃𝐎𝐎 𝚅𝟯𝟯 ⌨️ mechanical numpad can connect by 𝐁𝐓 up to 3 devices at the same time; toggle the mode switch to the Bluetooth mode on the back of the keyboard and long press ƒn﹢1 or ƒn﹢2 or ƒn﹢3 for 3~5 seconds to enter pairing mode. At this time, the 1／2／3 key flashes blue quickly to indicate that it’s ready to connect.
  2. Open the Bluetooth settings on your device and scan for available devices… Locate＆select any device name of the three groups: “CIDOO V33‑1” or “CIDOO V33‑2” or “CIDOO V33‑3”…
  3. Once the keyboard has connected to your device, the 1／2／3 key will cease flashing, and indicating that Bluetooth pairing was successful. Short press ƒn﹢1 or ƒn﹢2 or ƒn﹢3 to switch between paired Bluetooth devices.

The Bluetooth connection has memory. It will disconnect when the keyboard is powered off, and the keyboard will re‑connect to the last device when the keyboard is powered on again.

3. 2.4 𝘎𝘩𝘻 Wireless Connection:

• Toggle the mode switch to 2.4 𝘎𝘩𝘻 mode. Plug the receiver dongle into your device. The “4” key led will light on green for 3 seconds and then the whole keyboard 𝘣𝘢𝘤𝘬𝘭𝘪𝘨𝘩𝘵 light on indicates that 2.4 𝘎𝘩𝘻 connected successfully.
• 2.4 𝘎𝘩𝘻 pairing instructions: the keyboard 2.4 𝘎𝘩𝘻 mode is by default paired. If you need to re‑pair 2.4 𝘎𝘩𝘻 mode, perform the following operations:

Long‑press ƒn﹢4 to enter 2.4 𝘎𝘩𝘻 pairing mode… At this time, the “4” key flashes green color quickly. Insert 2.4 𝘎𝘩𝘻 dongle into the computer’s 𝐔𝐒𝐁 port. After the connection is successful, the “4” key stops blinking.✅

---

𝑨𝒖𝒕𝒐 𝑺𝒍𝒆𝒆𝒑 𝑴𝒐𝒅𝒆:

• After 5 minutes without a keypress, the backlighting will turn off to conserve battery. Any keypress will relight the backlight. After 30 minutes without a keypress, the keyboard will enter deep sleep under Bluetooth mode and disconnect, but any keypress will exit deep sleep mode, turn 𝐑𝐆𝐁 lights on, and initiate the Bluetooth re-connect to the keyboard. 𝑩𝒂𝒕𝒕𝒆𝒓𝒚‑𝑪𝒉𝒂𝒓𝒈𝒆 𝑰𝒏𝒅𝒊𝒄𝒂𝒕𝒐𝒓:

When the battery power of the keyboard is low (battery power less than 3.5 𝘃𝗼𝗹𝘁𝘀), the ƒn key will keep flashing red as a reminder of low battery. 𝑩𝒂𝒕𝒕𝒆𝒓𝒚‑𝑳𝒆𝒗𝒆𝒍 𝑪𝒉𝒆𝒄𝒌: ƒn﹢𝐏𝐀𝐔𝐒𝐄 Press＆hold ƒn﹢𝐏𝐀𝐔𝐒𝐄 can check the battery and charging status, with Battery‑Level indicator from 1 to 0 keys standing for 10%~100% (approximately); simply un‑hold those keys to exit this diagnostic mode.

• Press ƒn﹢𝐓𝐀𝐁 to check charging status: the 𝐓𝐀𝐁 key will light on red to indicate that the keyboard is charging, and the 𝐓𝐀𝐁 key will return to green 𝐋𝐄𝐃 once the keyboard is fully charged.

---

𝐂𝐈𝐃𝐎𝐎 𝚅𝟯𝟯 ⌨️ supports remapping keys via 𝐐𝐌𝐊／𝐕𝐈𝐀 firmware!

• 𝗡𝗢𝗧𝗘: Make sure the keyboard is properly plugged into the computer device, then 𝐕𝐈𝐀 installation steps are as follows:

1. Visit https://github.com/WestBerryVIA/via-releases/releases to download the latest 𝐕𝐈𝐀…
2. Download 𝐂𝐈𝐃𝐎𝐎 V33.JSON files from 𝐂𝐈𝐃𝐎𝐎 official website: 𝘄𝘄𝘄.𝐂𝐈𝐃𝐎𝐎.𝗰𝗼𝗺 and open 𝐕𝐈𝐀 Software, Click "File" and click "Import Keymap"…

• Installation is completed and 𝐕𝐈𝐀 software connected successfully if the correct keymap for the keyboard appears in 𝐕𝐈𝐀 configurator.
  • If 𝐕𝐈𝐀 software does not recognize the keyboard, 𝐂𝐈𝐃𝐎𝐎 does offer customer service assistance!
• 𝐕𝐈𝐀 should automatically detect your keyboard compatibility if it’s plugged in.

The keyboard memory is persistent, which means that wherever you plug in the keyboard, it should remember its settings.

• On the top half of 𝐕𝐈𝐀 software, choose one key which you want to change by your mouse, and then select the key on the bottom half of 𝐕𝐈𝐀 software to effect the remap.

• 𝐂𝐈𝐃𝐎𝐎 𝚅𝟯𝟯 ⌨️ does not have physical multimedia keys, but you can remap some keys through the 𝐕𝐈𝐀 software to achieve that functionality…
• 𝐂𝐈𝐃𝐎𝐎 𝚅𝟯𝟯 ⌨️ is configured with 4 layers from 0 to 3 by default, and each individual key can have multiple functions.

This is important for smaller keyboards, where there aren’t enough physical keys to handle all the functionalities you need.

• You can remap the key to replace the special key to the key you want, to achieve the quick operation of this layering functionality.
• 𝐂𝐈𝐃𝐎𝐎 𝚅𝟯𝟯 ⌨️ Layers allow you to configure your keyboard with more behaviors than its number of physical keys!

𝐂𝐈𝐃𝐎𝐎 𝚅𝟯𝟯 ⌨️ default＋customized 0-3 layers keyboard layouts as follows:

• 𝙇𝙖𝙮𝙚𝙧 0：This layer will be activated by default when the keyboard is connected to a device.
• 𝙇𝙖𝙮𝙚𝙧 1：When the keyboard is connected with the device, long‑press MO(1) to use.
• 𝙇𝙖𝙮𝙚𝙧 2：When the keyboard is connected with the device, remap any key to MO(2) by 𝐕𝐈𝐀 firmware and apply. This layer will be activated by long‑pressing MO(2) to use.
• 𝙇𝙖𝙮𝙚𝙧 3：When the keyboard is connected with the device, remap any key to MO(3) by 𝐕𝐈𝐀 firmware and apply. This layer will be activated by long‑pressing MO(3) to use.