AD7606B Platform Board Architecture - ArrowElectronics/data-storm-daq GitHub Wiki

DataStorm DAQ (Trenz Cyclone-V SoC Development Kit (TEI0022))

Analog Devices EVAL-AD7606B-FMCZ Development Board

The AD7606B Platform uses 2 boards. The Cyclone-V SoC Development Kit, and the EVAL-AD7606B-FMCZ board connects via an FMC interface.

DataStorm DAQ (Trenz Cyclone-V SoC Development Kit (P/N: TEI0022))

The DataStorm DAQ is based on the Intel Cyclone V SoC FPGA. It features, 1GB DDR3 each for the HPS and FPGA, 32MB QSPI memory each for the HPS and FPGA, Ethernet, and Power. For details, visit the Trenz Electronics Technical Reference Manual Wiki page.

The major components of the DataStorm DAQ (Trenz Cyclone-V SoC Development Kit) are identified by numbers:

Intel Cyclone-V SoC

SE Processor:
- Single or Dual ARM Cortex® A9 MPU
- Up to 925 MHz max clock speed
- 32KB L1 Program Cache (per core)
- 32KB L1 Data Cache (per core)
- 512 KB L2 Cache (shared)
- 181 HPS I/O pins
- 1 Hard Memory Controller (LPDDR2, DDR2, DDR3)
FPGA Fabric:
- Up to 110K Logic Elements (LE)
- Up to 5.5Mb M10K Memory
- Up to 621Kb MLAB Memory
- Up To 112 Variable Precision DSP blocks
- Up to 224 18x18 multipliers
- Up to 288 User FPGA I/O pins
- 1 Hard Memory Controller (LPDDR2, DDR2, DDR3)

FPGA DDR3
HPS DDR3
FMC LPC Connector
PMOD x4
microSD Card Connector
Ethernet PHY
RJ-45 Ethernet Connector
USB PHY
USB HUB
dual USB-A Connector
HDMI Transmitter
HDMI Connector
Intel MAX10
micro-USB to UART Connector for HPS Console
USB to JTAG and UART FTDI Bridge
micro-USB to JTAG and UART Connector for FPGA
SMA Connector
Push Button
LED
4-bit DIP Switch
12 VDC Power Jack
Clock Generator
Programmable Clock Generator
QSPI for HPS
QSPI for FPGA
Temperature Sensor
EEPROM

Analog Devices AD7606B Development Board

The EVAL-AD7606B-FMCZ evaluation kit features the AD7606B 16-bit, 800 kSPS, 8 channel analog-to-digital converter (ADC). A 7V to 12V external bench top supply is regulated to 5V and 3.3V to supply the AD7606B and support components.

The EVAL-AD7606B-FMCZ is an evaluation board that allows the user to evaluate the features of the ADC.

Full specifications on the AD7606B are available in the product data sheet, which should be consulted in conjunction with this user guide when working with the evaluation board.

Full descriptions of these products are available in their respective data sheets, which must be consulted when using the corresponding evaluation board.

AD7606B® - Precision eight channel 16-bit SAR ADC
ADP7118 - CMOS, Low Dropout Linear LDO for +3.3V, +5V Voltage supply.
ADR4525 - high precision, low power, low noise voltage references for external reference.
EEPROM

Analog Devices AD7606B Block Diagram

The block diagram of the EVAL-AD7606B-FMCZ® Eval board (below) shows the major components.Each analog input is bipolar input with CHx- channel connected to AGND. Conversion results from the AD7606B are communicated to the FPGA via the FMC-LPC connector using 4-channel SDO pin via SPI in serial interface mode or using 16bit parallel interface DB. both SPI and parallel interface along with BUSY and CNVST can be used as control function in ad7606B.

The EVAL-AD7606B-FMCZ evaluation kit features the AD7606B 16-bit,8 channel with 800 kSPS each, analog-to-digital converter (ADC). The AD7606B expects the input signals to swing between +AVCC and -AVCC. Analog input is bipolar with CHx- pin connected to AGND. Reference voltage can be given through both internal and external option through JP6, default at position B. interface type can be selected through PAR_N/SER_SEL pin through JP5 , default connected at position A.