U-Boot SPL 2025.07-ge5f40a8ed1ec-dirty (Oct 19 2025 - 11:33:49 -0400)
Reset state: Cold
MPU 1250000 kHz
L4 Main 400000 kHz
L4 sys free 100000 kHz
L4 MP 200000 kHz
L4 SP 100000 kHz
SDMMC 50000 kHz
init_mem_cal: Initial DDR calibration IO96B_0 succeed
DDR: Calibration success
is_mailbox_spec_compatible: IOSSM mailbox version: 1
LPDDR4: 1024 MiB
DDR: size check success
DDR: firewall init success
DDR: init success
Bloblist at 72000 not found (err=-2)
WDT: Not starting watchdog@10d00200
Trying to boot from MMC1
## Checking hash(es) for config board-0 ... OK
## Checking hash(es) for Image atf ... crc32+ OK
## Checking hash(es) for Image uboot ... crc32+ OK
## Checking hash(es) for Image fdt-0 ... crc32+ OK
NOTICE: SOCFPGA: Boot Core = 0
NOTICE: SOCFPGA: CPU ID = 0
NOTICE: SOCFPGA: Setting CLUSTERECTRL_EL1
NOTICE: BL31: v2.13.0(release):QPDS25.3_REL_GSRD_PR
NOTICE: BL31: Built : 11:22:42, Oct 19 2025
U-Boot 2025.07-ge5f40a8ed1ec-dirty (Nov 13 2025 - 07:53:54 -0500)axe5_eagle
CPU: Altera FPGA SoCFPGA Platform (ARMv8 64bit Cortex-A55/A76)
Model: SoCFPGA Agilex5 AXE5-Eagle
DRAM: 1 GiB
Core: 49 devices, 23 uclasses, devicetree: separate
WDT: Not starting watchdog@10d00200
WDT: Not starting watchdog@10d00300
WDT: Not starting watchdog@10d00400
WDT: Not starting watchdog@10d00500
WDT: Not starting watchdog@10d00600
MMC: mmc0@10808000: 0
Loading Environment from FAT... failed to set vqmmc-voltage to 3.3V
failed to set vqmmc-voltage to 3.3V
Unable to read "uboot.env" from mmc0:1...
In: serial0@10c02000
Out: serial0@10c02000
Err: serial0@10c02000
Starting HPS SMMU test for SDM.
sdm_tbu_stream_ctrl_reg_1_sdm : 0x3
smmuSetBaseAddr()
smmu1_S_IDR1.secure : 0x0
smmuInitStreamTable()
main(): Installing Event Queue
main(): Installing Command Queue
Issue commands to invalidate TLBs
main(): Enabling SMMU (Non-secure only)
smmuEnableCommandProcessing
smmuEnableEventQueue
smmuEnableTranslation()
main(): Intializing a context descriptor
smmuInitBasicCD:: Created CD:
0x0001e20a c0a00018
0x00000000 00075002
0x00000000 00000002
0x00000000 00ff4400
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
main(): Initializing Stream Table entry as S1, referencing the context descriptor.
smmuInitBasicSTE:: Created STE:
0x00000000 00074a09
0x0001b1c0 980000cc
0x00283500 000f0000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
smmuInitBasicSTE:: Created STE:
0x00000000 00074a09
0x0001b1c0 980000cc
0x00283500 000f0000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
smmuInitBasicSTE:: Created STE:
0x00000000 00074a09
0x0001b1c0 980000cc
0x00283500 000f0000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
smmuInitBasicSTE:: Created STE:
0x00000000 00074a09
0x0001b1c0 980000cc
0x00283500 000f0000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
smmuInitBasicSTE:: Created STE:
0x00000000 00074a09
0x0001b1c0 980000cc
0x00283500 000f0000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
smmuInitBasicSTE:: Created STE:
0x00000000 00074a09
0x0001b1c0 980000cc
0x00283500 000f0000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
smmuInitBasicSTE:: Created STE:
0x00000000 00074a09
0x0001b1c0 980000cc
0x00283500 000f0000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
smmuInitBasicSTE:: Created STE:
0x00000000 00074a09
0x0001b1c0 980000cc
0x00283500 000f0000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
smmuInitBasicSTE:: Created STE:
0x00000000 00074a09
0x0001b1c0 980000cc
0x00283500 000f0000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
smmuInitBasicSTE:: Created STE:
0x00000000 00074a09
0x0001b1c0 980000cc
0x00283500 000f0000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
smmuInitBasicSTE:: Created STE:
0x00000000 00074a09
0x0001b1c0 980000cc
0x00283500 000f0000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
smmuInitBasicSTE:: Created STE:
0x00000000 00074a0b
0x0001b1c0 980000cc
0x00283500 000f0000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
main(): Finish Streme table setup
smmuAddCommand:: Command is:
0x00000003
0x0000000a
0x00000000
0x00000000
smmuAddCommand:: START: PROD = 0x0 COND = 0x0
after smmuQueueFull
after entry
after for_command
smmuAddCommand:: Command is:
0x00000003
0x0000000a
0x00000000
0x00000000
after flushing 0x74800 - 0x74810
smmu1_S_IDR1.secure : 0x0
after increase queue counter
after waiting command to process
smmuAddCommand:: END: PROD = 0x1 COND = 0x1
main(): Finish invalidate STE
smmuAddCommand:: Command is:
0x00000046
0x00000000
0x00000000
0x00000000
smmuAddCommand:: START: PROD = 0x1 COND = 0x1
after smmuQueueFull
after entry
after for_command
smmuAddCommand:: Command is:
0x00000046
0x00000000
0x00000000
0x00000000
after flushing 0x74810 - 0x74820
smmu1_S_IDR1.secure : 0x0
after increase queue counter
after waiting command to process
smmuAddCommand:: END: PROD = 0x2 COND = 0x2
main(): Finish SMMU setup
start to set up translation table
Successfully set up translation table
This is HPS test.
Net: No ethernet found.
Hit any key to stop autoboot: 0
3248128 bytes read in 564 ms (5.5 MiB/s)
....FPGA reconfiguration OK!
failed to set vqmmc-voltage to 3.3V
failed to set vqmmc-voltage to 3.3V
failed to set vqmmc-voltage to 3.3V
failed to set vqmmc-voltage to 3.3V
failed to set vqmmc-voltage to 3.3V
47098368 bytes read in 7978 ms (5.6 MiB/s)
25391 bytes read in 22 ms (1.1 MiB/s)
## Flattened Device Tree blob at 86000000
Booting using the fdt blob at 0x86000000
Working FDT set to 86000000
Loading Device Tree to 00000000beb13000, end 00000000beb1c32e ... OK
Working FDT set to beb13000
Starting kernel ...
Deasserting all peripheral resets
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[ 0.000000] Linux version 6.12.33-g3234b1ed8956-dirty (soceds@soceds) (aarch64-none-linux-gnu-gcc (GNU Toolchain for the Arm Architecture 11.2-2022.02 (arm-11.14)) 11.2.1 20220111, GNU ld (GNU Toolchain for the Arm Architecture 11.2-2022.02 (arm-11.14)) 2.37.20220122) #1 SMP PREEMPT Sun Nov 16 12:12:54 EST 2025
[ 0.000000] KASLR disabled due to lack of seed
[ 0.000000] Machine model: SoCFPGA Agilex5 Arrow AXE5-Eagle
[ 0.000000] efi: UEFI not found.
[ 0.000000] Reserved memory: created DMA memory pool at 0x0000000080000000, size 32 MiB
[ 0.000000] OF: reserved mem: initialized node svcbuffer@0, compatible id shared-dma-pool
[ 0.000000] OF: reserved mem: 0x0000000080000000..0x0000000081ffffff (32768 KiB) nomap non-reusable svcbuffer@0
[ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000000bfffffff]
[ 0.000000] NODE_DATA(0) allocated [mem 0xbfdf3140-0xbfdf577f]
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000080000000-0x00000000bfffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080000000-0x0000000081ffffff]
[ 0.000000] node 0: [mem 0x0000000082000000-0x00000000bfffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000bfffffff]
[ 0.000000] cma: Reserved 32 MiB at 0x00000000bca00000 on node -1
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.5
[ 0.000000] percpu: Embedded 25 pages/cpu s61720 r8192 d32488 u102400
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: GIC system register CPU interface
[ 0.000000] CPU features: detected: Virtualization Host Extensions
[ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[ 0.000000] alternatives: applying boot alternatives
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootwait
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.000000] Fallback order for Node 0: 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 262144
[ 0.000000] Policy zone: DMA
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] software IO TLB: SWIOTLB bounce buffer size adjusted to 1MB
[ 0.000000] software IO TLB: area num 4.
[ 0.000000] software IO TLB: mapped [mem 0x00000000bea13000-0x00000000beb13000] (1MB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=4.
[ 0.000000] Trampoline variant of Tasks RCU enabled.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.000000] RCU Tasks: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
[ 0.000000] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: 544 SPIs implemented
[ 0.000000] GICv3: 0 Extended SPIs implemented
[ 0.000000] Root IRQ handler: gic_handle_irq
[ 0.000000] GICv3: GICv3 features: 16 PPIs
[ 0.000000] GICv3: GICD_CTRL.DS=0, SCR_EL3.FIQ=0
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000001d060000
[ 0.000000] ITS [mem 0x1d040000-0x1d05ffff]
[ 0.000000] ITS@0x000000001d040000: allocated 8192 Devices @85050000 (indirect, esz 8, psz 64K, shr 1)
[ 0.000000] ITS@0x000000001d040000: allocated 32768 Interrupt Collections @85060000 (flat, esz 2, psz 64K, shr 1)
[ 0.000000] GICv3: using LPI property table @0x0000000085070000
[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000000085080000
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] arch_timer: cp15 timer(s) running at 400.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0x7ffffffffffffff max_cycles: 0x5c4093a7d1, max_idle_ns: 440795210635 ns
[ 0.000001] sched_clock: 59 bits at 400MHz, resolution 2ns, wraps every 4398046511103ns
[ 0.000547] clocksource: timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604467 ns
[ 0.001154] Console: colour dummy device 80x25
[ 0.001316] Calibrating delay loop (skipped), value calculated using timer frequency.. 800.00 BogoMIPS (lpj=1600000)
[ 0.001331] pid_max: default: 32768 minimum: 301
[ 0.001430] LSM: initializing lsm=capability
[ 0.001611] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.001628] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.016844] rcu: Hierarchical SRCU implementation.
[ 0.016850] rcu: Max phase no-delay instances is 1000.
[ 0.017111] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level
[ 0.017327] fsl-mc MSI: msi-controller@1d040000 domain created
[ 0.018511] EFI services will not be available.
[ 0.020085] smp: Bringing up secondary CPUs ...
[ 0.024499] Detected VIPT I-cache on CPU1
[ 0.024614] GICv3: CPU1: found redistributor 100 region 0:0x000000001d080000
[ 0.024630] GICv3: CPU1: using allocated LPI pending table @0x0000000085090000
[ 0.024686] CPU1: Booted secondary processor 0x0000000100 [0x412fd050]
[ 0.028654] CPU features: detected: Spectre-v4
[ 0.028663] CPU features: detected: Spectre-BHB
[ 0.028669] CPU features: detected: SSBS not fully self-synchronizing
[ 0.028672] Detected PIPT I-cache on CPU2
[ 0.028716] GICv3: CPU2: found redistributor 200 region 0:0x000000001d0a0000
[ 0.028725] GICv3: CPU2: using allocated LPI pending table @0x00000000850a0000
[ 0.028756] CPU2: Booted secondary processor 0x0000000200 [0x414fd0b1]
[ 0.036589] Detected PIPT I-cache on CPU3
[ 0.036625] GICv3: CPU3: found redistributor 300 region 0:0x000000001d0c0000
[ 0.036635] GICv3: CPU3: using allocated LPI pending table @0x00000000850b0000
[ 0.036659] CPU3: Booted secondary processor 0x0000000300 [0x414fd0b1]
[ 0.036811] smp: Brought up 1 node, 4 CPUs
[ 0.036819] SMP: Total of 4 processors activated.
[ 0.036822] CPU: All CPU(s) started at EL2
[ 0.036828] CPU features: detected: 32-bit EL0 Support
[ 0.036831] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[ 0.036836] CPU features: detected: Common not Private translations
[ 0.036840] CPU features: detected: CRC32 instructions
[ 0.036848] CPU features: detected: RCpc load-acquire (LDAPR)
[ 0.036851] CPU features: detected: LSE atomic instructions
[ 0.036854] CPU features: detected: Privileged Access Never
[ 0.036856] CPU features: detected: RAS Extension Support
[ 0.036861] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[ 0.036928] alternatives: applying system-wide alternatives
[ 0.043763] CPU features: detected: Hardware dirty bit management on CPU2-3
[ 0.044193] Memory: 909780K/1048576K available (18304K kernel code, 4906K rwdata, 12104K rodata, 10496K init, 746K bss, 101120K reserved, 32768K cma-reserved)
[ 0.045404] devtmpfs: initialized
[ 0.051655] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.051686] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.054427] 21056 pages in range for non-PLT usage
[ 0.054439] 512576 pages in range for PLT usage
[ 0.054717] pinctrl core: initialized pinctrl subsystem
[ 0.056705] DMI not present or invalid.
[ 0.059742] NET: Registered PF_NETLINK/PF_ROUTE protoco
udhcpc: broadcasting discover
udhcpc: broadcasting select for 192.168.68.106, server 192.168.68.1
udhcpc: lease of 192.168.68.106 obtained from 192.168.68.1, lease time 7200
/etc/udhcpc.d/50default: Adding DNS 192.168.1.254
/etc/udhcpc.d/50default: Adding DNS 192.168.68.1
done.
Starting OpenBSD Secure Shell server: sshd
done.
Starting syslogd/klogd: done
Poky (Yocto Project Reference Distro) 4.3.3 agilex5 /dev/ttyS0
agilex5 login: root
root@agilex5:~#