U-Boot SPL 2023.10-31850-g84c6b5dd14-dirty (Jul 01 2024 - 06:50:34 -0400)
Reset state: Cold
MPU 875000 kHz
L4 Main 400000 kHz
L4 sys free 100000 kHz
L4 MP 200000 kHz
L4 SP 100000 kHz
SDMMC 50000 kHz
init_mem_cal: Initial DDR calibration IO96B_0 succeed
io96b_mb_init: num_instance 1
io96b_mb_init: get memory interface IO96B 0
io96b_mb_req: Write 0x10001 to IOSSM_CMD_REQ_OFFSET 0x1840043c
io96b_mb_req: CMD_RESPONSE_STATUS 0x1840045c: 0x10001
io96b_mb_req: IOSSM_CMD_RESPONSE_DATA_0_OFFSET 0x18400458: 0x20000000
io96b_mb_req: IOSSM_CMD_RESPONSE_DATA_1_OFFSET 0x18400454: 0x0
io96b_mb_req: CMD_RESPONSE_STATUS 0x1840045c: 0x10001
io96b_mb_req: CMD_RESPONSE_READY 0x1840045c: 0x10000
io96b_mb_init: get response from memory interface IO96B 0
io96b_mb_init: IO96B 0: num_mem_interface: 0x1
io96b_mb_init: IO96B 0 mem_interface 0: ip_type_ret: 0x1
io96b_mb_init: IO96B 0 mem_interface 0: instance_id_ret: 0x0
DDR: Calibration success
io96b_mb_req: Write 0x20020002 to IOSSM_CMD_REQ_OFFSET 0x1840043c
io96b_mb_req: CMD_RESPONSE_STATUS 0x1840045c: 0x30001
io96b_mb_req: CMD_RESPONSE_STATUS 0x1840045c: 0x30001
io96b_mb_req: CMD_RESPONSE_READY 0x1840045c: 0x30000
io96b_mb_req: Write 0x20020004 to IOSSM_CMD_REQ_OFFSET 0x1840043c
io96b_mb_req: CMD_RESPONSE_STATUS 0x1840045c: 0x1
io96b_mb_req: IOSSM_CMD_RESPONSE_DATA_0_OFFSET 0x18400458: 0x120
io96b_mb_req: IOSSM_CMD_RESPONSE_DATA_1_OFFSET 0x18400454: 0x8
io96b_mb_req: CMD_RESPONSE_STATUS 0x1840045c: 0x1
io96b_mb_req: CMD_RESPONSE_READY 0x1840045c: 0x0
LPDDR4: 1024 MiB
io96b_mb_req: Write 0x20040102 to IOSSM_CMD_REQ_OFFSET 0x1840043c
io96b_mb_req: CMD_RESPONSE_STATUS 0x1840045c: 0x1
io96b_mb_req: CMD_RESPONSE_STATUS 0x1840045c: 0x1
io96b_mb_req: CMD_RESPONSE_READY 0x1840045c: 0x0
ecc_enable_status: ECC enable status: 0
DDR: size check success
DDR: firewall init success
DDR: init success
QSPI: Reference clock at 400000 kHz
Trying to boot from MMC1
## Checking hash(es) for config board-0 ... OK
## Checking hash(es) for Image atf ... crc32+ OK
## Checking hash(es) for Image uboot ... crc32+ OK
## Checking hash(es) for Image fdt-0 ... crc32+ OK
WARNING: Data cache not enabled
NOTICE: BL31: Boot Core = 0
NOTICE: BL31: CPU ID = 81000000
NOTICE: BL31: v2.10.0 (release):QPDS24.1_REL_AGILEX5_GSRD_PR
NOTICE: BL31: Built : 09:32:51, Jun 19 2024
U-Boot 2023.10-31850-g84c6b5dd14-dirty (Jul 01 2024 - 06:50:34 -0400)socfpga_agilex5
CPU: Intel FPGA SoCFPGA Platform (ARMv8 64bit Cortex-A55/A76)
Model: SoCFPGA Agilex5 AXE5-Eagle
DRAM: 1 GiB
Core: 43 devices, 24 uclasses, devicetree: separate
WDT: Not starting watchdog@10d00200
WDT: Not starting watchdog@10d00300
WDT: Not starting watchdog@10d00400
WDT: Not starting watchdog@10d00500
WDT: Not starting watchdog@10d00600
NAND: 0 MiB
MMC: mmc0@10808000: 0
Loading Environment from FAT... Unable to read "uboot.env" from mmc0:1...
Loading Environment from UBI... SF: Detected mt25qu01g with page size 256 Bytes, erase size 64 KiB, total 128 MiB
Could not find a valid device for 10b80000.nand.0
mtd: partition "root" extends beyond the end of device "nor0" -- size truncated to 0x3e00000
Volume env not found!
** Unable to read env from root:env **
In: serial0@10c02000
Out: serial0@10c02000
Err: serial0@10c02000
Starting HPS SMMU test for SDM.
sdm_tbu_stream_ctrl_reg_1_sdm : 0x3
smmuSetBaseAddr()
smmu1_S_IDR1.secure : 0x0
smmuInitStreamTable()
main(): Installing Event Queue
main(): Installing Command Queue
Issue commands to invalidate TLBs
main(): Enabling SMMU (Non-secure only)
smmuEnableCommandProcessing
smmuEnableEventQueue
smmuEnableTranslation()
main(): Intializing a context descriptor
smmuInitBasicCD:: Created CD:
0x0001e20a c0a00018
0x00000000 00075002
0x00000000 00000002
0x00000000 00ff4400
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
main(): Initializing Stream Table entry as S1, referencing the context descriptor.
smmuInitBasicSTE:: Created STE:
0x00000000 00074a09
0x0001b1c0 980000cc
0x00283500 000f0000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
smmuInitBasicSTE:: Created STE:
0x00000000 00074a09
0x0001b1c0 980000cc
0x00283500 000f0000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
smmuInitBasicSTE:: Created STE:
0x00000000 00074a09
0x0001b1c0 980000cc
0x00283500 000f0000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
smmuInitBasicSTE:: Created STE:
0x00000000 00074a09
0x0001b1c0 980000cc
0x00283500 000f0000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
smmuInitBasicSTE:: Created STE:
0x00000000 00074a09
0x0001b1c0 980000cc
0x00283500 000f0000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
smmuInitBasicSTE:: Created STE:
0x00000000 00074a09
0x0001b1c0 980000cc
0x00283500 000f0000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
smmuInitBasicSTE:: Created STE:
0x00000000 00074a09
0x0001b1c0 980000cc
0x00283500 000f0000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
smmuInitBasicSTE:: Created STE:
0x00000000 00074a09
0x0001b1c0 980000cc
0x00283500 000f0000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
smmuInitBasicSTE:: Created STE:
0x00000000 00074a09
0x0001b1c0 980000cc
0x00283500 000f0000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
smmuInitBasicSTE:: Created STE:
0x00000000 00074a09
0x0001b1c0 980000cc
0x00283500 000f0000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
smmuInitBasicSTE:: Created STE:
0x00000000 00074a09
0x0001b1c0 980000cc
0x00283500 000f0000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
smmuInitBasicSTE:: Created STE:
0x00000000 00074a0b
0x0001b1c0 980000cc
0x00283500 000f0000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
0x00000000 00000000
main(): Finish Streme table setup
smmuAddCommand:: Command is:
0x00000003
0x0000000a
0x00000000
0x00000000
smmuAddCommand:: START: PROD = 0x0 COND = 0x0
after smmuQueueFull
after entry
after for_command
smmuAddCommand:: Command is:
0x00000003
0x0000000a
0x00000000
0x00000000
after flushing 0x74800 - 0x74810
smmu1_S_IDR1.secure : 0x0
after increase queue counter
after waiting command to process
smmuAddCommand:: END: PROD = 0x1 COND = 0x1
main(): Finish invalidate STE
smmuAddCommand:: Command is:
0x00000046
0x00000000
0x00000000
0x00000000
smmuAddCommand:: START: PROD = 0x1 COND = 0x1
after smmuQueueFull
after entry
after for_command
smmuAddCommand:: Command is:
0x00000046
0x00000000
0x00000000
0x00000000
after flushing 0x74810 - 0x74820
smmu1_S_IDR1.secure : 0x0
after increase queue counter
after waiting command to process
smmuAddCommand:: END: PROD = 0x2 COND = 0x2
main(): Finish SMMU setup
start to set up translation table
Successfully set up translation table
This is HPS test.
Net:
Warning: ethernet@10830000 (eth2) using random MAC address - ee:87:f7:e3:d5:68
eth2: ethernet@10830000
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found U-Boot script /boot.scr.uimg
2951 bytes read in 13 ms (221.7 KiB/s)
## Executing script at 81000000
crc32+ Trying to boot Linux from device mmc0
Found kernel in mmc0
Change the pullup values on EMAC2 HPS mii signals
Release Ethernet and USB PHYs from reset
9799650 bytes read in 438 ms (21.3 MiB/s)
## Loading kernel from FIT Image at 82000000 ...
Using 'board-0' configuration
Verifying Hash Integrity ... OK
Trying 'kernel' kernel subimage
Description: Linux Kernel
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x820000dc
Data Size: 9769848 Bytes = 9.3 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x86000000
Entry Point: 0x86000000
Hash algo: crc32
Hash value: 4dbd5dd0
Verifying Hash Integrity ... crc32+ OK
## Loading fdt from FIT Image at 82000000 ...
Using 'board-0' configuration
Verifying Hash Integrity ... OK
Trying 'fdt-0' fdt subimage
Description: socfpga_socdk
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x82951530
Data Size: 27933 Bytes = 27.3 KiB
Architecture: AArch64
Hash algo: crc32
Hash value: 1a7b67c9
Verifying Hash Integrity ... crc32+ OK
Booting using the fdt blob at 0x82951530
Working FDT set to 82951530
Uncompressing Kernel Image
Loading Device Tree to 00000000bf8d8000, end 00000000bf8e1d1c ... OK
Working FDT set to bf8d8000
Removing MTD device #2 (root) with use count 1
Error when deleting partition "root" (-16)
SF: Detected mt25qu01g with page size 256 Bytes, erase size 64 KiB, total 128 MiB
Enabling QSPI at Linux DTB...
Working FDT set to bf8d8000
QSPI clock frequency updated
RSU: Firmware or flash content not supporting RSU
RSU: Firmware or flash content not supporting RSU
RSU: Firmware or flash content not supporting RSU
RSU: Firmware or flash content not supporting RSU
Starting kernel ...
Deasserting all peripheral resets
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[ 0.000000] Linux version 6.1.68+ (soceds@ubuntu) (aarch64-none-linux-gnu-gcc (GNU Toolchain for the Arm Architecture 11.2-2022.02 (arm-11.14)) 11.2.1 20220111, GNU ld (GNU Toolchain for the Arm Architecture 11.2-2022.02 (arm-11.14)) 2.37.20220122) #1 SMP PREEMPT Mon Jul 1 08:03:32 EDT 2024
[ 0.000000] Machine model: SoCFPGA Agilex5 Arrow AXE5-Eagle
[ 0.000000] efi: UEFI not found.
[ 0.000000] Reserved memory: created DMA memory pool at 0x0000000080000000, size 32 MiB
[ 0.000000] OF: reserved mem: initialized node svcbuffer@0, compatible id shared-dma-pool
[ 0.000000] earlycon: uart0 at MMIO32 0x0000000010c02000 (options '115200n8')
[ 0.000000] printk: bootconsole [uart0] enabled
[ 0.000000] NUMA: No NUMA configuration found
[ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000000bfffffff]
[ 0.000000] NUMA: NODE_DATA [mem 0xbfde5a00-0xbfde7fff]
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000080000000-0x00000000bfffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080000000-0x0000000081ffffff]
[ 0.000000] node 0: [mem 0x0000000082000000-0x00000000bfffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000bfffffff]
[ 0.000000] cma: Reserved 128 MiB at 0x00000000b6800000
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.4
[ 0.000000] percpu: Embedded 21 pages/cpu s45224 r8192 d32600 u86016
[ 0.000000] pcpu-alloc: s45224 r8192 d32600 u86016 alloc=21*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: SYS_ID_AA64MMFR1_EL1[11:8]: forced to 0
[ 0.000000] CPU features: detected: GIC system register CPU interface
[ 0.000000] CPU features: detected: Qualcomm erratum 1009, or ARM erratum 1286807, 2441009
[ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[ 0.000000] alternatives: applying boot alternatives
[ 0.000000] Fallback order for Node 0: 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258048
[ 0.000000] Policy zone: DMA
[ 0.000000] Kernel command line: console=uart1,115200 root=/dev/mmcblk0p2 rw init=/sbin/init rootwait earlycon panic=-1 nosmp kvm-arm.mode=nvhe loglevel=8\r
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.000000] mem auto-init: stack:byref_all(zero), heap alloc:off, heap free:off
[ 0.000000] Memory: 824748K/1048576K available (17216K kernel code, 3776K rwdata, 9772K rodata, 8000K init, 613K bss, 92756K reserved, 131072K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4.
[ 0.000000] Trampoline variant of Tasks RCU enabled.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: 544 SPIs implemented
[ 0.000000] GICv3: 0 Extended SPIs implemented
[ 0.000000] Root IRQ handler: gic_handle_irq
[ 0.000000] GICv3: GICv3 features: 16 PPIs
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000001d060000
[ 0.000000] ITS [mem 0x1d040000-0x1d05ffff]
[ 0.000000] ITS@0x000000001d040000: allocated 8192 Devices @82040000 (indirect, esz 8, psz 64K, shr 1)
[ 0.000000] ITS@0x000000001d040000: allocated 32768 Interrupt Collections @82050000 (flat, esz 2, psz 64K, shr 1)
[ 0.000000] GICv3: using LPI property table @0x0000000082060000
[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000000082070000
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] arch_timer: cp15 timer(s) running at 400.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0x7ffffffffffffff max_cycles: 0x5c4093a7d1, max_idle_ns: 440795210635 ns
[ 0.000003] sched_clock: 59 bits at 400MHz, resolution 2ns, wraps every 4398046511103ns
[ 0.009581] Console: colour dummy device 80x25
[ 0.014198] Calibrating delay loop (skipped), value calculated using timer frequency.. 800.00 BogoMIPS (lpj=1600000)
[ 0.024703] pid_max: default: 32768 minimum: 301
[ 0.029403] LSM: Security Framework initializing
[ 0.034202] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.041596] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.052750] cblist_init_generic: Setting adjustable number of callback queues.
[ 0.060006] cblist_init_generic: Setting shift to 2 and lim to 1.
[ 0.066198] cblist_init_generic: Setting adjustable number of callback queues.
[ 0.073420] cblist_init_generic: Setting shift to 2 and lim to 1.
[ 0.079813] rcu: Hierarchical SRCU implementation.
[ 0.084612] rcu: Max phase no-delay instances is 1000.
[ 0.090203] Platform MSI: msi-controller@1d040000 domain created
[ 0.096365] PCI/MSI: /interrupt-controller@1d000000/msi-controller@1d040000 domain created
[ 0.104705] fsl-mc MSI: msi-controller@1d040000 domain created
[ 0.112344] EFI services will not be available.
[ 0.117280] smp: Bringing up secondary CPUs ...
[ 0.121821] smp: Brought up 1 node, 1 CPU
[ 0.125824] SMP: Total of 1 processors activated.
[ 0.130527] CPU features: detected: 32-bit EL0 Support
[ 0.135649] CPU features: detected: 32-bit EL1 Support
[ 0.140778] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[ 0.149357] CPU features: detected: Common not Private translations
[ 0.155604] CPU features: detected: CRC32 instructions
[ 0.160734] CPU features: detected: RCpc load-acquire (LDAPR)
[ 0.166461] CPU features: detected: LSE atomic instructions
[ 0.172014] CPU features: detected: Privileged Access Never
[ 0.177568] CPU features: detected: RAS Extension Support
[ 0.182958] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[ 0.190018] CPU: All CPU(s) started at EL2
[ 0.194174] alternatives: applying system-wide alternatives
[ 0.210215] devtmpfs: initialized
[ 0.222697] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.232487] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.254354] pinctrl core: initialized pinctrl subsystem
[ 0.262226] DMI not present or invalid.
[ 0.267135] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.274858] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[ 0.282044] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.289898] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.297900] audit: initializing netlink subsys (disabled)
[ 0.305012] thermal_sys: Registered thermal governor 'step_wise'
[ 0.305025] thermal_sys: Registered thermal governor 'power_allocator'
[ 0.311051] audit: type=2000 audit(0.192:1): state=initialized audit_enabled=0 res=1
[ 0.325357] cpuidle: using governor menu
[ 0.329596] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.336429] ASID allocator initialised with 65536 entries
[ 0.343983] Serial: AMBA PL011 UART driver
[ 0.369013] KASLR disabled due to lack of seed
[ 0.385443] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages
[ 0.392377] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page
[ 0.398660] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages
[ 0.405426] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page
[ 0.411673] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.418435] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page
[ 0.424681] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages
[ 0.431443] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page
[ 0.440046] gpio gpiochip0: (/soc/bridge@20000000/button-pio@108000010): not an immutable chip, please consider fixing it!
[ 0.451568] gpio gpiochip1: (/soc/bridge@20000000/button-pio@108000020): not an immutable chip, please consider fixing it!
[ 0.464350] ACPI: Interpreter disabled.
[ 0.470975] debugfs: Directory 'fixed-supply' with parent 'regulator' already present!
[ 0.479548] iommu: Default domain type: Translated
[ 0.484439] iommu: DMA domain TLB invalidation policy: strict mode
[ 0.491100] SCSI subsystem initialized
[ 0.495059] libata version 3.00 loaded.
[ 0.499226] usbcore: registered new interface driver usbfs
[ 0.504764] usbcore: registered new interface driver hub
[ 0.510106] usbcore: registered new device driver usb
[ 0.515294] usb_phy_generic usbphy: supply vcc not found, using dummy regulator
[ 0.522771] usb_phy_generic usbphy: dummy supplies not allowed for exclusive requests
[ 0.531788] pps_core: LinuxPPS API ver. 1 registered
[ 0.536753] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
[ 0.545868] PTP clock support registered
[ 0.549960] EDAC MC: Ver: 3.0.0
[ 0.556889] FPGA manager framework
[ 0.560424] Advanced Linux Sound Architecture Driver Initialized.
[ 0.567689] vgaarb: loaded
[ 0.570951] clocksource: Switched to clocksource arch_sys_counter
[ 0.577503] VFS: Disk quotas dquot_6.6.0
[ 0.581496] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.588655] pnp: PnP ACPI: disabled
[ 0.600743] NET: Registered PF_INET protocol family
[ 0.606120] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.615109] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[ 0.623587] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.631338] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.639136] TCP bind hash table entries: 8192 (order: 6, 262144 bytes, linear)
[ 0.647380] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.653914] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.660549] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.667806] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.674028] RPC: Registered named UNIX socket transport module.
[ 0.679986] RPC: Registered udp transport module.
[ 0.684680] RPC: Registered tcp transport module.
[ 0.689371] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.695802] PCI: CLS 0 bytes, default 64
[ 0.700915] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[ 0.709374] kvm [1]: IPA Size Limit: 40 bits
[ 0.718167] kvm [1]: Hyp mode initialized successfully
[ 0.725210] Initialise system trusted keyrings
[ 0.729918] workingset: timestamp_bits=42 max_order=18 bucket_order=0
[ 0.745378] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.752095] NFS: Registering the id_resolver key type
[ 0.757232] Key type id_resolver registered
[ 0.761410] Key type id_legacy registered
[ 0.765524] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.772212] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 0.779798] 9p: Installing v9fs 9p2000 file system support
[ 0.834592] Key type asymmetric registered
[ 0.838686] Asymmetric key parser 'x509' registered
[ 0.843682] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
[ 0.851066] io scheduler mq-deadline registered
[ 0.855589] io scheduler kyber registered
[ 0.878403] EINJ: ACPI disabled.
[ 0.914528] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.924298] 10c02000.serial: ttyS0 at MMIO 0x10c02000 (irq = 21, base_baud = 6250000) is a 16550A
[ 0.935316] SuperH (H)SCI(F) driver initialized
[ 0.940612] msm_serial: driver initialized
[ 0.946783] arm-smmu-v3 16000000.iommu: ias 48-bit, oas 48-bit (features 0x00081fef)
[ 0.955157] arm-smmu-v3 16000000.iommu: allocated 65536 entries for cmdq
[ 0.962506] arm-smmu-v3 16000000.iommu: allocated 32768 entries for evtq
[ 0.976684] arm-smmu-v3 16000000.iommu: SMMU currently enabled! Resetting...
[ 0.983888] arm-smmu-v3 16000000.iommu: msi_domain absent - falling back to wired irqs
[ 1.002582] loop: module loaded
[ 1.007961] megasas: 07.719.03.00-rc1
[ 1.016636] spi-nor spi0.0: found n25q00a, expected mt25qu02g
[ 1.022672] spi-nor spi0.0: n25q00a (131072 Kbytes)
[ 1.028587] 2 fixed-partitions partitions found on MTD device 108d2000.spi.0
[ 1.035709] Creating 2 MTD partitions on "108d2000.spi.0":
[ 1.041262] 0x000000000000-0x000004200000 : "u-boot"
[ 1.047915] 0x000004200000-0x000010000000 : "root"
[ 1.052737] mtd: partition "root" extends beyond the end of device "108d2000.spi.0" -- size truncated to 0x3e00000
[ 1.071260] tun: Universal TUN/TAP device driver, 1.6
[ 1.077705] thunder_xcv, ver 1.0
[ 1.081026] thunder_bgx, ver 1.0
[ 1.084317] nicpf, ver 1.0
[ 1.089094] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version
[ 1.096310] hns3: Copyright (c) 2017 Huawei Corporation.
[ 1.101679] hclge is initializing
[ 1.105031] e1000: Intel(R) PRO/1000 Network Driver
[ 1.109896] e1000: Copyright (c) 1999-2006 Intel Corporation.
[ 1.115685] e1000e: Intel(R) PRO/1000 Network Driver
[ 1.120641] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 1.126598] igb: Intel(R) Gigabit Ethernet Network Driver
[ 1.131985] igb: Copyright (c) 2007-2014 Intel Corporation.
[ 1.137578] igbvf: Intel(R) Gigabit Virtual Function Network Driver
[ 1.143839] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
[ 1.150298] sky2: driver version 1.30
[ 1.156679] socfpga-dwmac 10830000.ethernet: Adding to iommu group 0
[ 1.164036] socfpga-dwmac 10830000.ethernet: IRQ eth_wake_irq not found
[ 1.170651] socfpga-dwmac 10830000.ethernet: IRQ eth_lpi not found
[ 1.176931] socfpga-dwmac 10830000.ethernet: RX VLAN HW Stripping
[ 1.183186] socfpga-dwmac 10830000.ethernet: SMTG Hub Cross Timestamp supported
[ 1.190832] socfpga-dwmac 10830000.ethernet: User ID: 0x76, Synopsys ID: 0x31
[ 1.197984] socfpga-dwmac 10830000.ethernet: XGMAC2
[ 1.202944] socfpga-dwmac 10830000.ethernet: DMA HW capability register supported
[ 1.210407] socfpga-dwmac 10830000.ethernet: RX Checksum Offload Engine supported
[ 1.217863] socfpga-dwmac 10830000.ethernet: COE Type 1
[ 1.223075] socfpga-dwmac 10830000.ethernet: TX Checksum insertion supported
[ 1.230099] socfpga-dwmac 10830000.ethernet: TSO supported
[ 1.235567] socfpga-dwmac 10830000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 1.243556] socfpga-dwmac 10830000.ethernet: Enabled L3L4 Flow TC (entries=16)
[ 1.250769] socfpga-dwmac 10830000.ethernet: Enabled RFS Flow TC (entries=10)
[ 1.257885] socfpga-dwmac 10830000.ethernet: TSO feature enabled
[ 1.263872] socfpga-dwmac 10830000.ethernet: SPH feature enabled
[ 1.269859] socfpga-dwmac 10830000.ethernet: TX COE limited to 2 tx queues
[ 1.276715] socfpga-dwmac 10830000.ethernet: Using 40/40 bits DMA host/device width
[ 1.295572] dwc3 11000000.usb: Adding to iommu group 1
[ 1.367900] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 1.373423] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 1.383597] xhci-hcd xhci-hcd.0.auto: hcc params 0x0110ffcc hci version 0x110 quirks 0x0000000000010010
[ 1.393058] xhci-hcd xhci-hcd.0.auto: irq 43, io mem 0x11000000
[ 1.399231] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 1.404726] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 1.412370] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.1 Enhanced SuperSpeed
[ 1.420569] hub 1-0:1.0: USB hub found
[ 1.424385] hub 1-0:1.0: 1 port detected
[ 1.428801] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 1.437459] hub 2-0:1.0: USB hub found
[ 1.441255] hub 2-0:1.0: 1 port detected
[ 1.446119] usbcore: registered new interface driver usb-storage
[ 1.457044] i2c_dev: i2c /dev entries driver
[ 1.472835] sdhci: Secure Digital Host Controller Interface driver
[ 1.479019] sdhci: Copyright(c) Pierre Ossman
[ 1.484568] Synopsys Designware Multimedia Card Interface Driver
[ 1.492290] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.498201] sdhci-cdns 10808000.mmc0: Adding to iommu group 2
[ 1.508759] ledtrig-cpu: registered to indicate activity on CPUs
[ 1.518084] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
[ 1.525945] usbcore: registered new interface driver usbhid
[ 1.531519] usbhid: USB HID core driver
[ 1.546676] NET: Registered PF_PACKET protocol family
[ 1.551809] mmc0: SDHCI controller on 10808000.mmc0 [10808000.mmc0] using ADMA 64-bit
[ 1.560136] 9pnet: Installing 9P2000 support
[ 1.565217] Key type dns_resolver registered
[ 1.570419] registered taskstats version 1
[ 1.574600] Loading compiled-in X.509 certificates
[ 1.602598] i2c i2c-1: Added multiplexed i2c bus 2
[ 1.608032] i2c 3-0039: Fixed dependency cycle(s) with /soc/bridge@20000000/axi-hdmi@110000000/port/endpoint
[ 1.621838] mmc0: new high speed SDHC card at address 0007
[ 1.627401] i2c i2c-1: Added multiplexed i2c bus 3
[ 1.633323] mmcblk0: mmc0:0007 SS08G 7.21 GiB
[ 1.638158] i2c i2c-1: Added multiplexed i2c bus 4
[ 1.645578] i2c i2c-1: Added multiplexed i2c bus 5
[ 1.650550] mmcblk0: p1 p2
[ 1.653732] pca954x 1-0070: registered 4 multiplexed busses for I2C mux pca9544
[ 1.662689] stratix10-svc soc:firmware:svc: Adding to iommu group 3
[ 1.672175] Intel Service Layer Driver Initialized
[ 1.690874] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 1.697693] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 1.707688] ALSA device list:
[ 1.710690] No soundcards found.
[ 1.714756] Warning: unable to open an initial console.
[ 1.723725] EXT4-fs (mmcblk0p2): mounting ext3 file system using the ext4 subsystem
[ 1.751442] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Quota mode: none.
[ 1.760233] VFS: Mounted root (ext3 filesystem) on device 179:2.
[ 1.767195] devtmpfs: mounted
[ 1.777335] Freeing unused kernel memory: 8000K
[ 1.782446] Run /sbin/init as init process
[ 1.786563] with arguments:
[ 1.789527] /sbin/init
[ 1.792228] with environment:
[ 1.795362] HOME=/
[ 1.797711] TERM=linux
[ 1.859911] hub 1-1:1.0: USB hub found
[ 1.864317] hub 1-1:1.0: 5 ports detected
[ 2.350555] udevd[140]: starting version 3.2.12
[ 2.598961] usb 1-1.4: new high-speed USB device number 3 using xhci-hcd
[ 2.708849] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[ 2.724332] scsi host0: usb-storage 1-1.4:1.0
[ 2.814954] usb 1-1.5: new high-speed USB device number 4 using xhci-hcd
[ 3.342953] random: crng init done
[ 3.392006] udevd[144]: starting eudev-3.2.12
[ 3.760323] scsi 0:0:0:0: Direct-Access SanDisk Cruzer Glide 1.27 PQ: 0 ANSI: 6
[ 3.779871] sd 0:0:0:0: [sda] 31266816 512-byte logical blocks: (16.0 GB/14.9 GiB)
[ 3.791335] sd 0:0:0:0: [sda] Write Protect is off
[ 3.800218] sd 0:0:0:0: [sda] Mode Sense: 43 00 00 00
[ 3.811332] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 3.833839] sda: sda1
[ 3.839824] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 4.071618] EXT4-fs (mmcblk0p2): re-mounted. Quota mode: none.
[ 4.494234] socfpga-dwmac 10830000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 4.506336] socfpga-dwmac 10830000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-1
[ 4.518192] socfpga-dwmac 10830000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-2
[ 4.530077] socfpga-dwmac 10830000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-3
[ 4.541918] socfpga-dwmac 10830000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-4
[ 4.553879] socfpga-dwmac 10830000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-5
[ 4.565893] socfpga-dwmac 10830000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-6
[ 4.577911] socfpga-dwmac 10830000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-7
[ 4.621299] socfpga-dwmac 10830000.ethernet eth0: PHY [stmmac-2:01] driver [ADIN1300] (irq=POLL)
[ 4.637091] socfpga-dwmac 10830000.ethernet eth0: No Safety Features support found
[ 4.644681] socfpga-dwmac 10830000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[ 4.655833] socfpga-dwmac 10830000.ethernet eth0: registered PTP clock
[ 4.662751] socfpga-dwmac 10830000.ethernet eth0: FPE workqueue start
[ 4.669241] socfpga-dwmac 10830000.ethernet eth0: configuring for phy/rgmii-id link mode
[ 11.961716] [drm] Initialized axi_hdmi_drm 1.0.0 20120930 for 30000000.axi-hdmi on minor 0
[ 12.163056] Console: switching to colour frame buffer device 240x67
[ 12.185132] axi-hdmi 30000000.axi-hdmi: [drm] fb0: axi_hdmi_drmdrm frame buffer device
[ 14.312568] dw-apb-uart 10c02000.serial: failed to request DMA
Poky (Yocto Project Reference Distro) 4.3.3 agilex5 /dev/ttyS0
agilex5 login: